Good video, can you tell me where did you get the power for the lights?

you have way to many parts on that truck. And the mask is all I needed to see.

How are you making out with that BD 2 part a year later?? This is my 4th manifold (2 stock, 1 dealer aftermarket and now BD)... squealing yet again!!! Thinking gen 2 conversion...

Doesn’t work on 2015…

Luckily I can skip half the video. All that EGR crap is in the garbage 😂

I have the same truck in my shop now right rear tires wont spin locked up tight i thought the brakes can’t see anything wrong with them tried to remove the axle and she’s locked up tight in the rear end you ever run into anything like that? Pulled the cover oil looked decent and no metal chunks can’t see anything visible wrong and still can’t get the axle out

Are both balls the same size? I have a HF Jack clone that has a smaller and larger ball.

Idiots are all I see.

Would Biden be OK?

Can’t watch when you constantly spin the camera around

Didn’t work on mine. 2015 longhorn 3500. I removed both batteries overnight. Message came back on imediately. Even remembered the countdown mile

Lose the Trump sign

Didn't work

You make look so easy and it's not 😢

Always delete your truck…..problem solved…

I've been searching and searching for the torque specs for those damn axle flange bolts, 148ftlbs, thanks!!

What were the signs that it was giving that made u change the actuator? Looked like the problem was the turbo. Just what i seen😊

Got this same jack but I did this & it still won’t go up at all :( any suggestions?

There's a sensor on top of the engine right beside the turbo hose. The black square sensor on the engine pulls it off clean it put it back in, and your problem is solved. Spread this message around because this fix my truck it was a totally free Fix, everyone telling me that I needed to replace the engine or I needed a new Turbo😂

God Bless in Jesus Christ Name Amen.

Had nothing to do with installing throttle cable. 😢

Some people. Wonder if there parents had any children that survived at birth?

So did you replace the turbo or just cleaning it up allow you to move the vanes? Appreciate the video, replacing mine tomorrow with City Diesel actuator.

Thanks for the informative How To video. I'm in CT also and would like to transport an old W900 using a gooseneck and Ford F350. Be grateful if you could answer a few questions about Patrick's truck and trailer. Is Patrick's Big Tex 25GN gooseneck trailer a 25+5 length? I don't have a CDL and have a 2007 F350 dually. Does Patrick have a CDL or is he able to move this privately non-CDL as he is not for hire? Impressive to see this set up used to move a W900. Thanks again.

If you’re wiring those lights to reverse don’t also wire them to a switch. You’ll backfeed power into the reverse circuit on the tow vehicle and can easily cook the computer. You would have to use a diode on the aux feed circuit to eliminate the backfeed

Good shit my boys

I was having the loud squealing noise now I know why thanks a lot. Got my question answered why out asking 🎉

Love the Cummins engine... I wish the 7.3 was still in production... I owned a 98 and 99 E-350 with the 7.3L... best diesel powered engine international had... I wish I never sold those vans...

I always just tighten slack adjusters all the way. then back off 1/4. and about 1/2 on front brakes.

Guys just drain the old def put some expensive $20def jug reset check engine drive out... The message will come back countdown but once it feels that new def everything disappears after few miles driving..

I’m getting an exhaust service required See dealer now .. low power Any advice ?

I just tried it. I didn’t have any luck. Any other recommendations? I’m two hours away from home, so close to enjoy a break

And always carry an extra def injector

Says flood on the box no spot in the middle, the spot beams will say spot beam on the box. It's not dumb that it has side shooters on the outside that's where they need to be.... Thanks for being the Minister of Misinformation... you wanker misinformation wanker ... lighting the side (ditch lights)

Did the message come back up after driving for a while?

Typical cowboy shifting

Major overreving.

I have a 2015 cummins and it will not reset no matter how long you leave them disconnected.

These 2 videos game me the energy to rebuild mine and great helpful tip on clutch removal with bolt and oil

15mph in the left lane on their cellphone? This guy is definitely a Ram guy.

"East bound and down, loaded up and truckin' A-we gonna do what they say can't be done We've got a long way to go, and a short time to get there I'm east bound, just watch ol' "Bandit" run Keep your foot hard on the pedal Son, never mind them brakes Let it all hang out 'cause we got a run to make The boys are thirsty in Atlanta And there's beer in Texarkana And we'll bring it back no matter what it takes"

Man that truck looks good. You should paint it like in smokey and the bandit.

How is it with the new manifold?

12:10🤣🤣🤣

What year is this bad mofo?

I love this truck!!! bad boy right there!

Anyone that uses the jake brake while running bobtail is a rookie! No real trucker would ever do that. EVER!

Love the truck. Forget the haters. They had to learn also. I've been driving 34 years and still learning news things on a daily basis. Keep up the good work. You will get there.

I knew this guy was going to pick up the hot piece at 8:32