Colton's Garage

Пікірлер

@theodoredenissiano4872 6 күн бұрын

Which pins should I connect if I have a different connector? 1988 XJ. Please help!

@marcosrubalcaba9891 6 күн бұрын

Good job

@CreatingExcellence 13 күн бұрын

Just to note. These bikes run like crap with a bad battery.

@ThePoiuytreza1 17 күн бұрын

👍👍👍👍👍

@mylittlepitbull3143 22 күн бұрын

Hey buddy I had a similar problem where the brake fluid was old and had accumulated moisture inside the brake fluid and as the brake heated up then the brake fluid would expand because there was water inside the brake fluid so I just went ahead and bled The brakes replace the old fluid withnew fluid and that solved the problem.

@stilldeadrecords 24 күн бұрын

I coulda told you it’s been messed with. A 1980 bike wouldn’t have a kickstart, the engine also has classic kawasaki logos and that bike would have updated 79+ logos. Good job persevering on it, i’ve had similar problems with my 79 which is also swapped.

@CrazyPalidin57 Ай бұрын

I wish I knew where this wire was on my 07 3.7 Jeep Commander.

@JamesSnider-zw7cq Ай бұрын

Good job

@marisolfalcon6949 Ай бұрын

What model is the dakota in this video ?

@jerry-wl2hk Ай бұрын

Thanks a bunch. Easier than I thought. Great job explaining.

@tooltime9260 Ай бұрын

SO glad there's a MUTE button. Nothing worse than having to listen to retarded "music" to ruin things. Nice thing is that some day you'll grow up and not want to do these dumb things. Silence exists for a reason. Blaster is yuk. Use Knock-R-Loose instead.

@gunzmith29r 2 ай бұрын

will this work on a standard and an automatic trans?

@gunzmith29r 2 ай бұрын

good tip ..thanks for the vid

@MagneticMessengerofOrion 2 ай бұрын

You could’ve at least shined and cleaned it up if you’re gonna do a video showcasing it up close and saying you’re in love with it LoL

@Drimirin 2 ай бұрын

Got me and the wife to work at the last minute with this tip. Thanks for doing the groundwork of chasing out the circuit.

@JakudzaTeam 2 ай бұрын

Audi has different type motor, there are many types 1.9

@trippharris1144 2 ай бұрын

Sweet...... Thanks

@carlosdubon8539 2 ай бұрын

I'm thinking in buying a CFMOTO 450NK in black. But im afraid the paint is too fragile and would show swirls in just a few weeks. How many years/months would you say black paint stays prestine? Also, what would you recommend me? Black, White or Blue?

@ColtonsGarage 2 ай бұрын

I'd say it'd really depends on how you like to maintain your vehicles. Black will show all dirt and swirls more than any other color and will be the highest maintenance. White is the easiest color to maintain. It doesn't show dirt or swirls. Blue is a fairly easy color to maintain as well. My recommendation would be to watch some KZbin videos on proper washing techniques. Pan the organizer or AmmoNYC would be some good youtube resources to watch. By utilizing proper washing techniques, you will minimize your chances or marring and swirls. Personally, I wouldn't own a black vehicle, but a motorcycle doesn't see the same road grime and dirt that a full size vehicle does. So, it's not as big of a deal as you may think. Learn some proper washing techniques regardless and pick whatever color you like most without worry.

@richardmcallister5855 3 ай бұрын

Thank you

@CHEAPROLLIN 3 ай бұрын

Great tips! How's it coming

@ryanhead6924 3 ай бұрын

Great video man! Would the back right window regulator be the same as the front right? I have to replace the one in the back. Could you post the part number?

@oscarvogel2140 3 ай бұрын

They make a cheap plug set for those holes, that lasts longer than the foil tape.

@Mike-re7sq 3 ай бұрын

Thank you man 🙌🏼

@nathanlich9812 3 ай бұрын

Hey so I actually changed the alternator cause it wasn’t charging my battery, charged my battery and changed the starter and no start no crank, realized it was the neutral safety switch, started it in neutral and then turned it off and ever since then (an hr) it’s started in park. But I’m concerned that it’ll cause issues if I don’t fix it, or I’ll be back to starting it in reverse again so my question is is this a permanent fix and will it cause any issues if you do it right? Like any transmission or starter issues at all

@savtracc2116 4 ай бұрын

thank you for this video !

@TACO_SMACks 4 ай бұрын

I purchased a 2003 Yamaha v star 1100. I’m having a hard time with right now I really don’t know what else to check. Carbs are cleaned, new Petcock , new voltage regulator, and new battery. Bike ran good for 1 hour after replacing everything. Then all of sudden I get a backfire and the bike stalled. Now it’s just turns over and won’t start. Any idea what I could do? This my first bike and I haven’t been able to ride but that one time since I got it

@benjamingodinez4602 4 ай бұрын

Is this only a temporary fix would it burn any fuses

@kashmerrill8341 4 ай бұрын

I didn’t have to remove the engine shield, there was a spot for the drain plug and the filter.

@blackhawkbenxd7070 4 ай бұрын

The next time you do a video like this please show where and what we would need to remove. I mean this has helped me dramatically with understanding what's going on but you kind of skip some of these parts where yeah you don't want it to be like a 3-hour long video I fully understand that. But giving us a link to another video I wouldn't mind watching entirely where and what I have to remove.

@ColtonsGarage 4 ай бұрын

If I remember right, this is a really good video to watch that goes more in depth: kzbin.info/www/bejne/pGeqeaCwp5yod6ssi=ssIXLKVlD6phVMkN

@evanbloom2766 4 ай бұрын

I have a question good sir: Why do the blend doors have the foam covered holes in the first place? If you're able to cover them with solid tape, what is the thinking behind the foam? Also, Thank you for this video. I'm currently diagnosing my A/C Problems and i'm about to work on the actuator to the right in the glove box.

@ColtonsGarage 4 ай бұрын

The design was to allow a small amount of air to still pass through to prevent any whistling sounds that may disturb the driver. I can see the thought process, but even after fully taping the doors, I don't experience it. I suppose in theory, across millions of cars it was an issue, and they had a reason for it. This plagues most older VWs, Audis, and even Porsche uses the same design.

@trentonlong1537 5 ай бұрын

My Jeep at 45+ mph on highway jumps from over drive to the next gear down put new shift seloniods new filter still dose it ppl said bad battery or old terminals I had both so replaced those still having the shifting issue the tranny shifts good and strong in all gears no slipping at all no hard shifts just won’t stay in overdrive I got check engine light on for VSS A but I changed t cases and it came I had a shift seloniod code that’s why I changed them and no I just got VSS code ppl also say TPS or NSS Jeep idles and drives and great but I have hade it for 2 ish years now and it’s died 2 or 3 times when changing from R to N to D but it starts right back up plz help and I have a matco scan tool with live feed on it I was lookin at TPS data and the volts stayed at 0.8 0.82 and the precent was 0% it looks fine operates as should idk need help new to xjs.!!!

@maxaddicks1743 5 ай бұрын

shocks not struts

@StopTeoriomSpiskowym 5 ай бұрын

good maybe its possible in Seat Toledo /Audi A3 8L

@designertjp-utube 5 ай бұрын

Luv this Front Brake Demo! And you Boys did it in just under 5 minutes. My *Corona* *Extra* Beer had me excited to possibly hear you blurt out at frames 1:46 _"Once the nuts were cracked she was good to go!"_

@mikedenney1568 5 ай бұрын

what year is your dakota

@ColtonsGarage 5 ай бұрын

It's a 2002

@backinyourcar155 5 ай бұрын

Lazy video :(

@SharpShooter9867 5 ай бұрын

Why were your bags on backwards?

@ColtonsGarage 5 ай бұрын

I am cracking up 😂😂. You're right. I rode that bike for two years like that. No one said anything, and I never even realized it

@thegadphly3275 5 ай бұрын

Crazy stupid amount of extra work for a simple yet COMMON FAILING Harness, Why not design the plug nearer the end point?? Germen engineers should be chained to these cars and made to do the work bent over in the cold or hot sun in the driveway.. Why not just parallel the loom, and tape the new one on as well. Why strip it all , risking nicking and damaging other wiring.. ANother stupid idea by VW engineers. Almost as stupid as the old style lug nuts/Bolts that are almost impossible to line up in the dark by the side of the road... in the rain..

@Wakeupandsniffthecoffee 6 ай бұрын

No jack stands? Cringy!

@thefeistywombat Ай бұрын

Drilled and slotted rotors were cringy too 😂

@matthewcolella984 6 ай бұрын

i spent the past week putting in a new starter, new relays, new ignition switch and a new ignition cylinder and still had the no crank no start problem. before throwing in the towel, i tried your hack and GOD DAMN it worked! idk how you figured this out but it's genius. like they say, not all heroes wear capes. many thanks from Colorado.

@matthewcolella984 2 ай бұрын

quick update for anyone following these comments: while this bypass definitely works, it also makes the check engine light come on. and this only matters when you have to get an emissions test. state regulators will not pass a vehicle with a check engine light on. so eventually, you'll still have to replace the NS switch.

@brandonwinter1050 6 ай бұрын

Thanks a ton man! I have a 2000 Jeep Cherokee Sport, and it was having electrical problems starting, so after messing around with the starter and the wires, i gave up and decided to try youtube😂 I found your video, and the solution worked like a charm👌👌 Thanks!

@thedaveko 6 ай бұрын

what is a fair price to replace the glow plugs and harness on a 2002 golf tdi?

@ColtonsGarage 6 ай бұрын

If you were to take it to a shop, I would guess somewhere around $350-$500?

@thedaveko 6 ай бұрын

@@ColtonsGarage is that mostly labor?

@thedaveko 6 ай бұрын

Just trying to figure out if it's worth trying to do myself.

@ColtonsGarage 6 ай бұрын

@thedaveko If you do it yourself, parts are around $100, and it'll take around an hour of work. At a shop, parts are typically marked up 20-50%, and labor rates usually between $75-$150hr.

@kralljazz 6 ай бұрын

Brilliant!

@radostinanastasov7726 6 ай бұрын

Hey man, thanks a lot for this video I wanted to know if I can apply tape on the vents withouth removing everything on my dad's car and thanks to you now I do! :) Just an advice, please, more videoing on the process.

@martinvanwell10 6 ай бұрын

Problem. 08 dakota 4x4. 2 wheel ABS. Lose coontrol on snow cause rear brakes wontt sttop pushing when trying to stop. No ABS warning light . 2 chrysler dealers cant find the problem

@ColtonsGarage 6 ай бұрын

They won't stop pushing as in the rear brakes are still engaging or are engaging too hard and locking up the wheels?

@martinvanwell10 6 ай бұрын

@ColtonsGarage not engaging. They continue to push the truck as the front disk brakes lock up

@canadianrugby7 6 ай бұрын

Man, this was a no explanation for nothing at all video. Why post it?

@ColtonsGarage 6 ай бұрын

Can you elaborate?

@jobehayes8444 7 ай бұрын

Be careful there was Technical service bulletin from Dodge for caliper pinhole stripping out happened to me how to get knuckles from the junkyard

@williambrown6623 7 ай бұрын

Smart, excellent !!

@michaelboyer9429 7 ай бұрын

As an old person, not wanting to get up underneath it or couldn’t, this is a ass saver. Thanks.

@chrispulham4779 8 ай бұрын

Way too go Man,,, don't give up

Ең жақсы KZbin

Пікірлер