Пікірлер
@nicolelane4551 17 сағат бұрын
This is so awesome do they sell big jugs of this silicone rubber resin
@familyacademy360 Күн бұрын
Can food be eaten on resin plates?
@claytonjames4779 Күн бұрын
Using acrylic can reduce the strength and also take longer to cure, right? Why not use pigments meant for the medium?
@angelagordon3102 Күн бұрын
This is happening with my premixed resin the bottoms are still partially wet and the tops are sticky ,I keep putting more time on the curing lamp but it is still giving issues.
@yasminaf3699 2 күн бұрын
Hello! i wanted to ask if cutting white cardstock 300 gsm will leave dark mark on the edges. Please if you can show some demo will kelp me decide if i am going to go for it.
@maryamsaidu7842 4 күн бұрын
Beautiful work,my questions is wont the ink spread by the time you are adding the top coat resin?and if its happens how can one prevent it
@Muhsinah.Nadeem 5 күн бұрын
Thank you
@GaryMcKinnonUFO 5 күн бұрын
I bought 5mm acrylic sheets to replace the metal trays since my trays weren't level, so all i had to do was level the dehydrator and all is good :)
@GaryMcKinnonUFO 5 күн бұрын
Thanks Edna, i went out and bought one after watching your vid, 2 hours at 70C,such a difference in production time ! Thanks very much, liked and subbed :)
@EdnaWargon 5 күн бұрын
@GaryMcKinnonUFO welcome to my channel, Gary. I use mine all the time unless it's hot outside 🙃 thanks for subscribing!
@GaryMcKinnonUFO 5 күн бұрын
@@EdnaWargon :)
@NinaHansen2008 6 күн бұрын
Thank you.
@EdnaWargon 5 күн бұрын
@@NinaHansen2008 my pleasure 🙏
@kathys.3420 7 күн бұрын
If I have the mold and I need to make a replica. Do I fill in with silicone or plaster, clay?
@EdnaWargon 6 күн бұрын
@kathys.3420 this video I did will explain everything kzbin.info/www/bejne/mqOVl6dvqdV7racsi=NyossZEa_O4QbKCw
@trolpgaming7058 8 күн бұрын
Thankss
@sanaimran9792 8 күн бұрын
After how many hours should we de mould it
@EdnaWargon 8 күн бұрын
It depends, of it's hot a few hours but keep checking
@EllieAndrade-s7t 9 күн бұрын
Where do you buy crystal pieces? Also do you put a board under canvas mine tends to dip in middle?
@EdnaWargon 9 күн бұрын
if the canvas is small no need to, it wont dip. for a larger canvas add some thick cardboard to the back before pouring. i make my own crystals :)
@catalenaj1212 10 күн бұрын
Have you engraved chargers?
@EdnaWargon 9 күн бұрын
chargers, do you mean made from metal?
@vichardman61 10 күн бұрын
Get ride of music makes your videos better sorry but high pitch music causes my ears to ringing I have Ménière disease so I can’t listen to hype noises great video though teaches me a lot
@peachjo122 13 күн бұрын
What type of of epoxy resin did you use? Deep pour?
@EdnaWargon 13 күн бұрын
@peachjo122 The links are in the description, but no, you can use a non deep pour for this since it's not deep
@martinebangs6520 16 күн бұрын
Hi Edna, new to channel, enjoyed this video so I joined....Take care...🍁 🍁
@EdnaWargon 9 күн бұрын
Thank you too Martine and welcome to my channel 💕
@mariatobar7937 16 күн бұрын
Soo cool.Thank you
@EdnaWargon 9 күн бұрын
Glad you like it! 🙏
@mariatobar7937 16 күн бұрын
Very nice tutorial lovely
@EdnaWargon 9 күн бұрын
Thank you so much 😊
@maryraquelmarcano9817 16 күн бұрын
Como sabes las medidas del material con respecto al proyecto sea corte o grabado ??
@trudycooke8155 18 күн бұрын
Hello I'm in the UK and loved this and realise an airbrush is a great addition what psi is your airbrush? Do you have any links for your airbrush please. Trudy
@EdnaWargon 18 күн бұрын
@@trudycooke8155 hi. To be honest I don't have a link for it because it's a tool I bought years years and years ago for another purpose and as for the PSI have no idea either.Sorry I can't help on that front but if you look up the brand pixie , you might find it somewhere online. I'm glad you enjoyed the video😊
@trudycooke8155 18 күн бұрын
@@EdnaWargon hi thanks I did look it up but sadly could find nothing on Pixie but thank you for replying.
@EdnaWargon 18 күн бұрын
@trudycooke8155 www.amazon.com/Aeolian-Pixie-Professional-Airbrush-Compressor/dp/B0085Y8L2W/ref=cm_cr_arp_mb_bdcrb_top?ie=UTF8
@trudycooke8155 17 күн бұрын
Thank you that's very kind of you. Unfortunately it's no longer available on that link and I can't get it in the UK. I don't know where else to find it but shall keep looking!
@mathkor89 21 күн бұрын
For others, it’s proffered you pour the silicone in one place so the silicone can rise and push the air out, the thinner the stream of silicone the better , bubbles will pop as the pour, Edit: also pour it close to the bottom to help push the air up and out
@JimCarlson-dg2kw 22 күн бұрын
Awesome Jim wife Gods great
@annjenellesosing2774 23 күн бұрын
is this kind of resin food safe? or you can just only use it for displays? I'd like to use resin to my custom mug and plate but I'm not sure if it can be used as kitchenware?
@EdnaWargon 23 күн бұрын
@annjenellesosing2774 I use mine as a sugar bowl for example. As I've said in many of my tutorials nothing hot.
@wildbluewings 24 күн бұрын
I did the perfect 1:1 ratio but it still didn't cure properly...what the heck?!
@EdnaWargon 24 күн бұрын
@@wildbluewings what brand of resin did you use?
@wildbluewings 23 күн бұрын
@@EdnaWargon Modpodge
@EdnaWargon 23 күн бұрын
@@wildbluewings modpodge resin???
@wildbluewings 23 күн бұрын
@@EdnaWargon Is that bad stuff? 😖
@EdnaWargon 23 күн бұрын
@wildbluewings well in all the years working with almost all resin brands out there, it's the first time I've heard of the modpodge brand! The secret to any good quality brand of resin is the correct ratio, correct mixing, and curing time that's different for each brand and formula. If you have any left, try again 😉
@Sam-ql4ze 24 күн бұрын
Would these hold water?
@EdnaWargon 23 күн бұрын
f you varnish them inside and out with a water resistant varnish it should be good
@WendyBurtenshaw-yl2hs 25 күн бұрын
The mould is so very pretty Edna, love the results from all of the moulds😊❤
@EdnaWargon 25 күн бұрын
@WendyBurtenshaw-yl2hs 🙏 thanks Wendy 💕 always fun to make DIY molds!
@mcgarrett-xw2fm 26 күн бұрын
show you a respirator
@buzzbuzz7365 26 күн бұрын
The mold turned out lovely
@EdnaWargon 26 күн бұрын
@buzzbuzz7365 thanks 😊
@karenmclaughlan9128 29 күн бұрын
A beautiful piece of art to hang proudly on the wall 😍
@EdnaWargon 29 күн бұрын
@karenmclaughlan9128 thank you Karen 😊 🙏
@georginagallagher2807 29 күн бұрын
Wow very beautiful thanks for video😊
@littlemouse1927 Ай бұрын
Can you get different colours with the F1 on black cards? Or will it always engrave silver? Thanks ☺️
@EdnaWargon Ай бұрын
@@littlemouse1927 it depends what colour cards you buy, some have other background colours, check the options on their website using my links 👍🏻
@sanjanajain1149 Ай бұрын
Ma'am y material kaise purchase kr sakte h
@mariatobar7937 Ай бұрын
Muy hermoso
@U2cantrustme Ай бұрын
At the end here did i hear you say if I join I get free resin? I need some resin, i just started learning resin art so I can cast my moms flowers in resin from her funeral service when i get good at it. I bought tons of silicone molds from ebay to learn all about resin art. I am using the middle of this cake molds to make a clock tonight. This will be my biggest pour so far. Thanks for video I am learning a lot..
@JimCarlson-dg2kw Ай бұрын
Love it Gods good awesome Jim wife Tara
@barbridingsTheResinator Ай бұрын
So adorable! That tool is amazing. Maybe Santa will bring me one!
@anneallen3578 Ай бұрын
What a brilliant tool thank you for sharing love Anne 🎉🎉🎉
@jskerritt74 Ай бұрын
I just came across your channel, I will love to learn about Resin jewelry make. Can you tell me what tools are needed to begin
@EdnaWargon Ай бұрын
i did this video a few months ago that might help you :) kzbin.info/www/bejne/gKnYpGOhZq6Fpbc
@vonnie4781 Ай бұрын
This helped me so much with making some decisions on my project! Thank you sooo much!
@EdnaWargon Ай бұрын
@@vonnie4781 🩷 fab, love helping out 🙂
@karenmusa3052 Ай бұрын
The double sided tape is a great idea, thanku very much. Loving the lego idea too 😅 ❤
@karenmusa3052 Ай бұрын
Oh wow the magnetic rulers...brilliant. Thanku
@EdnaWargon Ай бұрын
@@karenmusa3052 💕💕💕
@Anjuchanana2 Ай бұрын
Gorgeous ❤
@EdnaWargon Ай бұрын
@@Anjuchanana2 thank you 😊
@NancySimonds Ай бұрын
Beautiful!❤
@Anjuchanana2 Ай бұрын
Beautiful ❤❤❤
@anneallen3578 Ай бұрын
Just one word STUPENDOUS XXXXXX🎉🎉🎉🎉🎉
@EdnaWargon Ай бұрын
@anneallen3578 💕 thanks Anne
@hazelloving41 Ай бұрын
Excellent work........I do have a question......what I'd the name of the food dehydrator that you used in this video?
@EdnaWargon Ай бұрын
all the details in this video 💕 kzbin.info/www/bejne/gmW1pXuGf96Bo8U
@jaykb6587 Ай бұрын
So far, I have done exactly one mold. It didn't turn out very good. In the five years since, molding materials have improved greatly. I hope. This encourages me to try again. 🤞 It would been nice to see how the sides could been accentuated if you had tried rubbing in another color. ?
@barbridingsTheResinator Ай бұрын
Marvelous save! I want some of that chocolate cake! Looks delicious! Love the bags. Good luck hope you sell out!
@EdnaWargon Ай бұрын
@barbridingsTheResinator 🥰 Well Barb, I wish I could say the chocolate cake lasts long enough to give you a slice! Unfortunately, the minute I make it, it's gone 🤩
@barbridingsTheResinator Ай бұрын
@@EdnaWargon You bake too? what can't you do?! Just love your personality and videos
@EdnaWargon Ай бұрын
@barbridingsTheResinator 😁 I do, I'm actually intolérant to wheat and milk so I made the one you saw, I just replaced the flour for spelt flour and I made a soy cream and chocolate ganache, it's delicious 😋
@barbridingsTheResinator Ай бұрын
@@EdnaWargon 😋😋😋😋
@jaykb6587 Ай бұрын
I've heard that if you put a tiny bit of blue into these resins, it helps keep resin from yellowing. After I found JDiction resin, I haven't had this problem. Last year I did a test for my different resins, both UV and epoxy. Leaving them out in the sun all summer, only the cheaper resins yellowed. My JDiction ones are still doing great.
@EdnaWargon Ай бұрын
@jaykb6587 well, one brand I used was cheap so I'm not surprised but the other wasn't and it still yellowed. 🤔