I noticed you disconnected a couple hoses. Do you need to drain the coolant to do this job? That would bite, because I just drained and restored my coolant but I definitely need a new gasket for my vacuum pump on my 07 Beetle.

I was wondering if you guys still do the ride annually? Thanks

I am getting my cat from MagnaFlow Exhaust. It’s $484 but it will meet EPA emissions

Let’s do a RAD 40th ride from the train station to bowness park. I’m a local, totally down

I've performed this procedure three times on my 3.6, and it has saved me a significant amount of time. Here's a step-by-step guide to help streamline the process. Wrench Modification: Take a 14mm wrench and bend the ring end in a vice, ensuring you can look through down the shaft and see the ring sticking out. Then, cut about 5mm off the end of the ring, creating a cut-out hole. This will allow you to pass the wrench through the fuel line and tighten the screw more easily. Cleaning Carbon Deposits: While the manifold is off, it's a good opportunity to clean the carbon deposits. Use a socket and rotate the crankcase to clean cylinders 2-4-6, followed by 1-3-5. Be sure to block the open valve holes with tissue. You can use a drill with cable ties... yes insert about 5 cables ties into the chuck of the drill head and tighten, spray cleaner to effectively remove buildup, or a scraper as needed. Afterward, ensure everything is thoroughly cleaned. Injector Seal Maintenance: The 3.6 is known for injector seal leaks, so it's a good idea to replace them while the manifold is off. The parts are inexpensive ($3-$5 each on Amazon). You’ll need: 3 X 03H198149A (Fuel Injector O-Ring Kit - Upper) 3 X 03H198149 (Fuel Injector O-Ring Kit - Lower) You can change these end seals without removing the injectors, I also use rubber greese on the seals which helps with install and seal. Additionally, I recommend using a new manifold gasket each time. However, if you don't have a replacement and need to reuse the old one, apply Permatex Aviation Form-A-Gasket Sealant (liquid and paste) generously over the gasket. I also use this sealant on new gaskets. The reason for this is that it makes removal much easier when you need to take the manifold off again in the future. I hope this will help alot of people. Regards Dan

Do both sides swivel? How do you know what side goes on top and bottom?

What’s the little piece on the wire for the horn called mine is missing it

Never supposed to use silicone RTV for this application. The OMC manual explicitly mentions this. Silicone RTV will dissolve in the presence of gasoline.

Which bulb is for the low beam, the bottom one or the upper one inside the circle? Thx

why no video on removing it from the boat?

This is amazing. Thank you for taking the time to make this video. It's going to save me sooo much time and gives me the confidence to rip my leg off and get going.

Con You really need to re edit your video! Pro it’s nice to see a job like this done without a vehicle lift.

Does the unit need to be removed from the boat. That shifter cable has me worried.

Hello Are those two different neutral safety switch interchangeable ? Can i use new tyle of transmission in my old neutral switch type transmission ?

Really nice car! You did a lot of research to get it correct, part of the fun of doing one of those cars. I have a 1/24 scale right now, but someday......

truly beautiful mate orange cars matter.

So that's where the ass slide was wow. thanks

Doing this tomorrow. Seems easy. How did you enjoy the coil spring installation?

Was about ready to scrap my ol boat, till i found your channel. We'll see how this goes. Steering cables next.

On my, that pin hole sucks lots of air it sounds like a vacuum! And I have lean codes on both banks! Is it normal to suck so much air? Just wondering if you knew!

Great video! Thanks! Just what I needed to see. The shift cables were what I was worrying about the most. This is magic. Super appreciate it.

Was the exhaust gasket shown in this video the correct one? Walkers diagrams seem to indiciate its not

Thank you for posting, been putting off doing this service myself. Do you have a video of the removal or replacement of the leg itself, or is that pretty self explanatory?

How did you get the shift cable removed from the lower unit

236,159 miles must be some sort of record! Gives me hope.

Hope this helps

Helpful video. And yep often those rear coil springs are broken. For the AWD version there’s no third party ones that I found so had to get from a dealer. (I used an online Toyota parts dealer which was about $150 less per spring than the local dealer)

Thank you for the awesome video! Very helpful! There’s another gasket at the bottom bottom of that oil cooler. If you notice the big nut on the inside of the oil filter canister, that can be removed with a 46 mm socket and just beneath there is another rubber gasket. If you remove that first, it’s a little easier to do this job because you can take the entire thing out.

Man wish you would have made a video removing everything first

Where did you get the replacement part from

The original color of the general Lee is t&t express

Looking forward to Rad 40

Does anyone know definitively which house had the pool where Cru 360's out of? I live on Bow Crescent where it was filmed however that was the one scene I missed the location. Thanks! Love the video btw.

Thanks for posting.

Man i gotta put it back on tommorow smh 2nd one ive done still same struggle i dint even know how i took off or put back the other one i just remember fighting that danm metal line to the fuel rail

Hi Percy. Can you confirm that you did not have to remove the exhaust to get the transmission out? Looks like connectors, shifter, coolant lines and axils but not the exhaust pipe

❤ thank you so much for this! I'm elated my new replacement battery is working after your very helpful and easy to follow video.. I was quoted £150 and did iit myself after watching this. Very grateful 😊😊😊

Great vids! Which house is the pool house? In google earth none of the roof outlines match the film for this neighborhood, was it torn down/new house built on the property?

Thank you. Useful video.

hey Percy i have question here i bought a used transmission to put on my 2007 versa hatchback, but the CVT connector is different and the shiffting wire, so is there any chance to adapt this transmission and make it work on my car, Thank you

Sorry the the comment defaulted to the middle of the screen

How did you get the manifold off of the lower fuel rail? I'm stuck there it won't come off even after loosening that nut that you said you used a 14mm on

This is exactly what I need to do for my sisters old bug. THANK YOU. Trying to seat it just wasn’t working because it would pull away. But putting pressure behind the plug while pressing on the light had them turn on.

Bro my laptop turn on and goes off in seconds

Is the 800 Stringer the same

Thank you for this. I've had this sound for 6 months maybe more! It was jerking as well. I'm changing the coils, plugs and catalytic. I think a bad coil or plug contributed. I do have ~140k on it.

The champher on the clear ring faces up lightly coated with grease. Anyone working on these do yourself a favor and invest in a manual. That orange silicone tells me someone’s been there before. Ring was upside down and sealant required is permatex 2. Not silicone. If not sealed properly it can draw in exhaust gases causing overheating.

❤

I have try opening the laptop twice and hadn't had any luck 😅. I want to make sure I can do it myself so i can order the battery

Stunning ❤