4 piece set cost me 80.00 great video . Found my set at x reload🎉

May I ask what rail that is you have on your GP100?

Try the same rounds & loosen the stock screws , torque the screws to 7&1/2 inch pads , shoot ,10in pads shoot & go up 5 at a time to 35 & see what the best is . We did this with a savage & went from 1&3/4" groups to 3/8" groups at 50

If you want an accurate measurement from Center, to Center, measure one of the bullets you were shooting, then zero the caliper, and measure from edge to edge. Zeroing out the caliper with a bullet in it will give you a measure from center to center of each group.

Thanks for the tutorial. Do you deburr or clean the primer pocket before priming?

Great video and great information

2 worst kinds of ammo

Limb saver makes a cheap barrel tunner.they work.

You want it closer to the end of the barrel. Same as the limbsaver device start about inch and a half back and move until desired outcome.

you don't lube your brass before inserting into the various dies?

Thanks for making the video! I've got the larger 5 station hornady reloader, but I haven't used it in a long time. I just wanted to see the process to remind myself of how to do it!

Get in touch with Ruger your Rifle Needs Work! Chamber is to SHORT

Crimp die is in setting die

I use 20 grains of h110 for my 357 loads. It works great.

I shoot 125s, bullets touch in the group at 25 yards shot off sand bags. On my GP 100, I replaced the block-style front sight and replaced it with a beade-style of front sight and a v notch on the rear sight. This makes for a very fine hold on targets at extended ranges. 17.8g of H110 with any 125g Jacketed bullet with a cci 550 is very, very accurate at 1750-1800 fps. For goodness sakes, if you are shooting for accuracy, sort your brass by brand.

jajajaj💪

I don't have the highest standards, but if a .22 can't put 10 shots into 1 inch at 50 yards with even one kind of bulk ammo, it is not accurate and i am disappointed. Esp bolt actions. Then it's time to move it along. Thanks for sharing your journey though. I have had guns that just wouldn't shoot too.

This is too anal...I shoot for fun lite reloads in 38 sp and 357 in my 686+1 6in steel plates at 25 yards...red dot in revolver just doesn't seem right...but knock yourself out...!! 🙂 As I am certain a villan or threat will not care about your data... in the real world of course.!!

I notice you didn’t have a good cheek weld to the stock. Press your face into the stock so you aren’t orbiting around the ocular of the scope and your eye stays centered. If you don’t you’ll see poor results.

I know this video is old, but I'd like to point out that the max load shown in the Hornady manual is not 15.0. The max load is shown in red, 15.6.

Your didn’t show how to measure the correct length. Plus you didn’t crimp your round. This is very dangerous if you don’t crimp!

Best accracy with .22lr will always come from Subsonic.

I made a load of 18.4 of H 110 it’s a hot load that book is old get a new book it has a max load of 21 gr of H-110 I have a GP 100

I loaded 18.4 grains of H-110 with 125 XTP Hornady bullets pretty strong load but my GP-100 handle it no problem but I think I’m going to back the load to17.9 h 110 also try accurate #9 works well to and don’t need as much

I loaded some with 18.4 gr of H-110 haven’t tried it yet but it’s right out of the manual with 125 XTP bullet how high have you gone ?

Kids need to go thru learning..Barrel harmonics is real BUT NOT ON 22 rimfire... What matters is quality of lot is AND VELOCITY.. Standard vel around 750 fps to 1150 fps 40 gr tip...Barrel length slowing velocity to 1150 est is better than any harmonics With a 22..Stabilizing bullet is key,,assuming action is screwed in with proper moderate to hard tightness..

No data just a lot of BS avoid this clown

You're a serious waste of time

Gotta laugh...just because it says Titegroup does not mean it shoots a tighter group! All marketing!

7.5 grs of titegroup does pretty well its a max load for 357 mag with 125gr xtp in lee manual and hodgen website

Would you happen to know of a holster for that with the rail?

how much crimping did you do on the 38 special 125Grain tightgroup

Have you loaded with magnum primer I just bought a gp100 in 6 inch barrel and I have found some loads with cci 500 using 2400 just wondering if you have tried it

I have the same rifle. Your just over thinking it. Mu group's started the same as yours. But after around 50 rounds the group's started closing up and now all of my group's are under 1". Don't clean it till this happens. I don't clean my 22s till around 250-300 fired. Its a learning process not a quiting process. My ruger likes cci standard. Good luck.

I didn’t know California allowed for someone to reload their own ammo.

One other thing..., pull a bullet from a case, drive it down the barrel and mic it for its diameter (lands-to-lands). Manufacturer bore tolerance on .22LR can vary from .220 to .223. Then omitt any ammo brand that doesn't mic to AT LEAST match bores O.D.. The better the bullet seals the bore (larger O.D.) the more consistent accuracy tends to be. STANDARD velocity ammo is what competitors use also. Even try sub-sonic ammo. Some rifles are sensitive to "trans-sonic transition". After that headspacing for "jump" can /may improve grouping. It all depends on what you're attempting to achieve.....

An 1"+ group at 50 yards is horrifying.

Also need to shoot different brands and weights to see what your pew-pew likes best, THEN go from there.

Check and play with action screw torque first.

Hello sir, ru still in SoCal? I have a rubber tuner from limbsaver I could give it to try. They’re pretty cheap I’m in the Riverside area, lmk and we could meet.

if someone says uh or uummmmm 50 over and over uhhhhhhhhh skip it

Did this model of RAP .223 come with AR mag and mag release from the factory? or is it the older ones with the flush fit rotary? I was wondering how the current AR mag versions works around aftermarket stocks like this.

If you want a bit of weight up front & You don't have threads, go on E-Bay & order a muzzle brake of some type for that rifle. They come in steel & aluminum. Sometime these help with a bit of weight up front to rid of vibrations. I would not be happy with that rifle the way you have it shooting even with cheap ammo.

Eeeeh.., still wouldn't take head shots on squirrels with those groups. Too risky.

😄 Nice! Glad you got it grouping.

Holy smokes! My CZ 457 shoots better groups at 100 yards. Did you get it shooting any better?

Try that same load in a 38 spl revolver for comparison.

One thing this did was to eliminate the flyers.

Check the bedding, put a new crown on it

Back in the mid to late 70 ruger put out some good guns and now they just put out lots of guns and they won't shoot the truth is quantity not quality as is the same thing with for instance some of the other companies like savage it is hard to find us quality anymore and that's a fact and also a shame that you have to go outside the good old usa to get a good rifle this is just my opinion enough said shoot well and have a good day. Beagleman