You should remove this video. I am absolutely astonished that you off all people have the rear bearing plate removed from this machine and could easily demonstrate replacing the power cord properly. Instead you are advocating people cutting the power cord, leaving the remnants of the old power cord wires in place and using butt splice connectors to connect a new power cord. For starters, people often replace their power cords because the cords are damaged. On vintage machines quite often (as you are well aware) the internal shielding is often dry rotted and brittle and often not even safe.. Why would you replace a power cord and leave ANY remnants of the old wiring in place? Secondly, adding butt splice connectors add resistance to the electrical. While the amount of resistance may be negligible depending on the quality of the butt spice connectors it’s still completely avoidable by connecting the replacement power cord properly to the connections at the field coil using the factory wire caps. I realize that some people may not be capable of removing to speed control, governor, rear bearing plate, etc. to get to the factory wiring, but why advocate a half assed repair. It is a perfectly good way to take a UL rated machine and make it unsafe and potentially dangerous. Further, there are mechanical linkages under the machine that could easily compromise those spice connections for somebody that isn’t experienced with this stuff. Another reason to avoid a Mickey Mouse repair and butt splice connections. The correct power cord with ground and a proper strain relief would avoid having to splice in a power cord designed for a solid-state model.

This video helped much more than the original one I commented on, maybe the angle of the video helped but I got it!

Thanks so much for posting these videos. It enabled me to compete the job without too much pain. Without them I'd have had no chance lol

Anyone have an idea when the motors will be back in stock??

How do I get your address to get mine fixed . When it's locked, the head is loose. And the lock mechanism black piece is starting to come off. Probably needs an inside clean

My k5ss shakes a lot will the regreasing eliminate that or are there other procedures I need to follow?

Hey great videos. My wife used her pro600 like 4 times to make butter and now nothing there is power going to the motor when turned on. Can I bench test the motor by putting power and neutral to the motor leads?

This feels like the longest KZbin short I've ever watched 😮

Is that planetary intergalactic?

Thank you very much you are awesome

The springs might not have, but I'm sure that somebody came on the professional 600 Pro 5 Plus Style.

I did it! 🎉

Dude get a tripod so you can use both hands.

Damn, this is excellent!! I'm sending mine just for the upgrades. Thanks!

Oh boy I need your F bomb sticker #snapring

Very very informative. Helped me decide which machine works well for me. However, tell me ,.. do all the machines have batter sprayed into the machine?? then wouldn't we need to clean up every time by opening the head???

20 years ago, the Kitchen Aid was a great stand mixer. Unfortunately it has been consistently "value engineered" to reduce cost and I have come to hate the motor, gearing, and speed control on my new 5 quart unit. I'm giving up, sending it to Goodwill, and will be buying an Ankarsrum.

Beater mixer fixer

How could all of that work be cheaper than any machine? I hate throwing things away I cannot tell you how many things I’ve had people say they did not work and literally it’s like a belt or a bad race not connected

What about the fucking oil?

The other person using your stuff. Is Jeff Bezos and Amazon itself? They have their own department that develops and steal peoples intellectual property. And have China make it. All sels goes to Amazon

What type of grease did you use?

What type of grease did you use?

❤️🩷🙂😊

And how much does something like this cost? I work in a food manufacturing laboratory and have like 10 or more of these mixers and they are not cheap at all lol

This is the best explanation of any rebuild. You are very very good.

You had me “pull this shaft” right out

I wish I had the money to get mine fixed I use my mixer all the time

Thoroughly helpful video, THANKS!!!!! When it came to putting the pin back into the planetary, I found that a large nail set tool worked better than a punch since the head of the nail set tool is recessed.

Mine is stuck on high, i will try and look at it carefully and see if I can adjust it following your instructions.

I can fix air conditioning over the phone 📞!Hi my air conditioner is making a wobble when I turned it on after winter 🥶?theirs a mud wasps nest on your fan blade 😂👌

What grease do you use?

Is the Pro600 deluxe the same as these mixers? Mine just stopped turning yesterday and I'm trying to find out if I can fix it, and if so- what do I need to do so!!

Hey Mr. Mixer, a quick question, but first thanks a lot for your help! Your videos are entertaining and a really helpful resource. My question: is it normal that my KitchenAids speed on 10 is oscillating? It's not 100% consistent and while running sometimes drops noticeably and then comes back to full speed over and over again. Like every few seconds. If not, what is causing this behavior? I couldn't find anything about it online. Thanks in advance for your help!

$30 to ship it, and how much to fix it plus shipping back? Fix it yourself or buy a new one.

Amazing!!

Mine didnt have them bc we in a small town in maine

Omg!!! This video saved my mixer. I got to deep cleaning my machine and turns out that I didn’t put the motor brushes back in properly! Thank you so much.🎉

Sent an email on the website weeks ago, never received a reply🤷‍♀️

This reminds me of AVE's teardown of one of these.

please not scream in the video thank you ❤

You doing this one handed is impressive.....the only thing that would be more impressive would be to do it...left handed. :-)

Love your videos! Always great and clear instructions! I’m in Australia and was wondering if the Inox MX6 NSF H1 grease would work? Just trying to find something I can get locally in Aus. :) thanks heaps

I have a couple of these KitchenAid mixers. The newest one is from 94. But my big one is a Hobart 60 quart, I believe it's a 2.5 hp. It's been mixing dough every day since 1983.

Bought a spring and washer kit for my new Artisan mixer easy to install and holds paddle in place like it should Thanks Mr Mixer

Cool beans!

It took a lot of q tips, paper towels, gloves, and tub o towels but I got it done with your guidance. Thank you! My wife is making cookies tonight to try it out. Now she wants me to maintain her mother’s machine, too! If 13 years looked as bad as ours then I can’t imagine what her machine looks like…

Super informative, shows the design reasoning. Love the fact that you include QR codes with the product to find these videos!

Great video, super easy to follow along

KitchenAid mixer resto-mod is not something I ever would have thought existed, very cool though.