@@ronzrolly8723 yeh it’s great I’ve been using it for a few months now and it’s been very reliable, and doesn’t add any noise

@@nashoxley-jenner6599 don’t know much about the new models sorry

@@gercarey3261 Sometimes the switch won’t pull out from the front , I should have checked first

@@Thestripper1 Sometimes the switch won’t pull out from the front , I should have checked first

@@brettdavid6491 Hey mate , no modifications to the frame , but had to much around with the bearing stem a bit. You can see the full mods here www.tapatalk.com/groups/hondatrailcts/ct110-enduro-dirt-bike-project-t11734.html And we call them postie bikes in Australia as that’s what the postal workers used to ride to deliver the mail.

@@VadimAnatolich LBM-10

@@Brennosguitarsandgear thanks a lot! Them so hard to identify

@@georgeboomsmamusic I don’t find it noisy at all Dispatch master is the GOAT

@@hirangabijoychakraborty6639 correct

@@TheOutdoorLifeTOL yes default

@@gsusheist tinyurl.com/6595638b

@@Brennosguitarsandgear thank you,

@@gearoiddom you can put it into different modes , for direct to interface , or into front of amp , into effects return etc. It can adapt to whatever your situation. This example is the direct mode

@@gearoiddom it has different modes depending on your use. Direct to interface or into an amp etc

@@Brennosguitarsandgear OK Thanks. I'm still confused though as to what is being achieved and why the 'into an amp' option is there at all. So - say we select a simulation of a Marshall stack on this pedal but we run that a small Peavey combo. We end up with some sort of hybrid tone. The ultimate colouration of the Peavey circuit and its inbuilt speaker cone can't be removed. That is the origin of the sound coming to our ears. Makes no sense. Only makes sense in a pedal direct to audio interface setup.

as per the title it was the crunch mode on both channels , just with different settings

@@Brennosguitarsandgear Thought so - but the difference in noise seemed so great! … Thanks for confirming 😎👍🏼

@@kierenmoore3236 just a bit more noise floor from the extra gain dialed in

@@Brennosguitarsandgear Sure. Cheers, bro

@@rowanvanwilligen8973 yep

@@rowanvanwilligen8973 And 11 nice amp simulations, plus an FX loop to place time based FX (like delay and reverb). Makes sense since you're using the amp's distortion circuit.

Mooer radar no tiene amplificadores, solo simula cabinas 🤭

There is no speaker simulator built in , so no

Boost pedal in the FX loop brings up the overall volume without adding gain. Boost in front of the pedal adds gain and compresses the sound , but won’t significantly raise the volume, especially on an already gained up tone. Hope that makes sense

Gotoh GTGB707-403

Yes it overrides the original, But you can reset it back to stock in the software

30 inch

Glad it helped

I chose that one because it is well balanced (not too trebly, not too bassy) I’ve found that once you find a good, well balanced IR , it tends to work with most amplifier sims

@@Brennosguitarsandgear Cool thank you. I will just use that specific one and see how it goes. Its a little overwhelming and time consuming trying to figure out what the best ir's are for each amp.

Great fun to build 👍🏾

Yeh it’s a ripper. Got a Duncan screamin demon in the bridge , and a dimarzio cruiser in the neck. Duncan in the middle, but can’t remember the model

@@Brennosguitarsandgear thanks heaps!

Just got to learn to play like you and I’ll be set 👍🏾🎤🎸

@@Brennosguitarsandgear haha 😝

Engine and electrics are all stock

@@Brennosguitarsandgear what year is it in have an 81 with a hi low but I have points and I was thinking of changing to CDI

@@wayneschembri3754 92 model from memory