👍🏼

One coshen hav hoto repir termo ajast met

Lisa, I just bought the little plunger part, from your company, of course. I couldn't believe how easy this was to replace. My iron is now working again. Thank you so much!

I lost the some part long ago and thanks to this i know that its a spring ..thankfully i manage to for aome spring and finally repaired mine.

How to put it on KZbin

Үтікті қалай тазалайды

How to make the vapor come out

En Colombia su precio real gracias me gusta

Great video thank you

Thanks for the infor👍

Delivered in Pakistan?

these are looking kinda small we need big bags for clothes we wash

AWESOME .... can you do a video about the laundry bags you sell so we can see how much clothes can fit inside thanks

Why my mini boiler consume a lot of water? I already replaced it with a new valve. I hope that you could help me please. Thanks

I believe you mark one spanner holes to the motor case. You only turn counter clockwise when two spanner holes are equal distance from that mark. You turning too much the way I read it. It's not the two spanner wrench holes from the wrench. It's the two spanner holes near the mark you make.

This is the only instruction that solved my problem! I didnt know the paper had only one "right" side! Thanks!

Why dont you make a video showing how to replace a leaking seal on these pumps? You sell the seal kit.

What are you using to hold the water tank up? What kind of stand is that?

Sorry guys but this isn't Thomas Jennings - kzbin.info/www/bejne/ppaYXpKnnsuSm7M

I have a brand new Sapporo 527. About an hour after I started using it tonight, the iron would not stop steaming, eventually dripping out as a fast leak. Would the plunger be the culprit for this? Any idea what would cause such an issue on a brand new machine?

i want this iron

what is its price

This woman will be found in Pakistan

This was so helpful! Thanks so much for the great walk through

BEST VIDEO FOR GRAVITY IRON ❤❤❤🎉

My work needs to do this!

Thicc asf

Very good day, first of all, congratulations on the videos you upload, they are always very useful and have particularly helped me a lot. Please keep uploading videos like this. Please if you can help me with the following: I have a TM-T20ii that sometimes prints perfectly and other times it stops on the first line, check the motor, sensors, clean the head. When it prints the print is of good quality. I have tried it with the startup test by turning off and holding down the “Feed” button and sometimes it prints the entire report, sometimes only the first lines, sometimes up to half and it throws an error. When I turn it on normally, the error light comes on for a second and then goes off (I don't know if it's normal). I have another similar printer and it was working perfectly, but when I cleaned the head (with a cotton swab and isopropyl alcohol, printer turned off and then I blew to evaporate all the alcohol) the same thing started happening to it (I have seen some people do it). They clean with WD40, I don't know if it is recommended). I don't know if after cleaning you have to reset something. Both printers have less than 4Km of head usage (they last 150KM), when they print the quality is good. However, I don't know if cleaning damages the head, but I followed the steps that the website recommends doing for this purpose. It would help me a lot to know your opinion, if something similar ever happened to you and how you solved it, thank you very much in advance for everything.

wtf? You just replaced it and didn't repair the problem! also how tf did you know that the problem has to be the valve and not something on the pcb like a switch or condensator

Anyone know where the rubber grommet fits into this? I see it on the exploded view in the manual, but I can't figure out where it goes on the actual part.

Thank you. I learned a lot watching this.

Short, sweet, simple, and fixed exactly what I needed. Thank you so so much!!

I have a one like that , plz explain me , Why does the button keep broking

Sadly my Hi Steam MVP 35 quit heatingthe water. I cannot afford a new setup. The iron is still working. I received a list of repairshops all in other states. Florida and Carolina not doing it any more.. What other steam generator irons do you suggest for use in all my families pressing needs.? I don't want to go back to regular irons. I am spoiled.

can you change iron to a different iron?

Where is the contact information for this company? Can distilled water be used instead of using the gravel/filter sand packages? Thank you

Gravity iron is the best thing ever

Sapporo iron black wire in back I see three , one to pump A ground left alone.

Worked perfectly with some alcohol and microfiber cloth. I had sticky buildup on the metal print head. Just cleaned it and printed my labels again and they're perfect. Thanks for the video!

Hi awet use this printing haw Mach the price cani use for plastic?

I think this is the part that I need to replace on my ES85AF iron. The parts losr calls it the handle cap switch. Are we talking about the same part here? I will need to order it and want to order the right part.

When checking the manual for my ES85AF iron the part you call a microswitch seems to be called a handle cap set. Is that the part I need?

Just checked the plunger, which was pretty simple. Spring seemed fine, but the switch does not move the plunger when tested as per instructions. No clicking sound. Is there a replacement for the switch?

What a shit printer having to mess with dip switches

Where I can order steam switch for laundry iron

Your number please

Thanks a lot I’ll try tonight

My question,is ,some water is coming out from the hose nipple ,close to the plunger part when steaming

Boiler is not producing steam. I have replaced the heating element believing that was problem.