Started out as a nice video of a good running outboard. Then you ruined it by doing the high rpm rev. Folks DO NOT do that to your outboard.
@msamour18 күн бұрын
I'm having back pressure issues. The water pump is brand new. It pumps fine if the rubber cover for the gear linkage is off, but it won't pump at all if it's on. An old guy that worked on these motors years ago told me to drill some pressure relief holes. I'm trying to figure out where, and what size. Other than that, the motor is mint. It's an 84, and was used a total of 4 hours in the 80's. I'd be a shame to junk the motor for such a stupid problem.
@jasonbeason478019 күн бұрын
Working the throttle by hand, you're not moving the timing. It won't rev up and run right if the timing isn't moved along with the throttle. They move in sync timing and throttle.
@jmcooney200021 күн бұрын
Fab thanks!
@lonnieblackwelder831026 күн бұрын
Can i put a 10hp carburetor on a 7.5 Honda motor??
@bryanpineda9150Ай бұрын
Do this thing got and air filter or is it just a air vent/port
@whiskeyminer1073Ай бұрын
I’m fixing up one of these myself anyway I could connect with you? My shut off valve is leaking just wondering how you hooked yours up? Parts are not available.
@whiskeyminer1073Ай бұрын
Where can you get pars for these? Looking for fuel valve and gas cap that doesn’t leak (open close vent cap)
@hyundaireviewsАй бұрын
Is the mixture knob the idle pin for the carb? My engine seems to bog out at idle unless I give it throttle. I’m guessing it’s my idle pin
@user-ty6bw6il8wАй бұрын
It did help me , but at the same time you need to know there are two sizes of bushing, I ordered both but the beefier one came first and my brother & I had to pound it from underneath to get it to dislodge fron the frame. I wish it came out the way yours did. We used the one we had but needed to go to Ace hdwe to get a 20 threaded nylok nut to stop from it coming loose while riding because the thicker bushing left fewer threads to fasten to end of shaft and used blue thread lok to help insure. it woul not come loose. All in all Thanks for the video 5 stars buddy.
@zng85562 ай бұрын
do you guys know what engine you used?
@zng8556Ай бұрын
as well as how you attached the tires?
@Ajaxaxxess2 ай бұрын
Impact is your friend
@perrydallas11122 ай бұрын
What ratio should i mix the coolant at? Would only be summer use but dont want to ho straight water.
@WW2JeepandRifle2 ай бұрын
50% coolant to 50% water. For Summer use, ok to increase water amount up to ~75% as long as you don't leave it like that into the colder seasons. More water will cool better
@BryanOblinsky2 ай бұрын
Have to manually unlatch it from underneath
@BryanOblinsky2 ай бұрын
I have one that the trim stays locked
@robertsrbell78113 ай бұрын
Just wondering why not clean the old one sure there's nothing wrong with it .
@jordbjor13 ай бұрын
I got the same exact one I’ve had if for 21yrs and runs really good. The weed less prop chews through everything. Just picked up a 74 for $25 going to try to get that running worst case I’ll have spare parts for the one I already have
@zingo26643 ай бұрын
an absolute beauty, look after her !!!
@HorsepowerHouse3 ай бұрын
I know some people disagree, but, you can use an impact driver to remove the flywheel (on the center bolt of the puller.) Some are easy to remove, some not. Same with most magnetos and flywheels on these engies, motorcycles, atv's, dirtbikes, etc.
@gregoryvangaya89714 ай бұрын
So that's all salt water if you're on the ocean?.. going right into the cylinder?
@twizzler3b4 ай бұрын
Thank you. Off to check mine...
@jaxonsadventuresandgaming43144 ай бұрын
Can you make a video on how to run it after you change your spark plugs
@jalayahjohnson54865 ай бұрын
Thanks guys. This was an easy task that I had no idea on how to do. Now I do!!!
@highlandoutboards5 ай бұрын
Glad it helped!
@DarkStarDireWolf6 ай бұрын
Cool video! I just scored one of these the other day! About to change the oil and replace the lines and clean it out a bit, do you have a video on servicing these?
@user-dy8by7vw1e6 ай бұрын
Where can i buy the carburettor?
@bayfish_91566 ай бұрын
about how much fuel does is use?
@lukeozdigger57306 ай бұрын
Mixture adjustments would be on the needle on the carb slide you can move it up or down a few knotches, that screw in the side is an adjustment for the idal/slide height
@MaybeMyBad01137 ай бұрын
良い色だ
@MrMultiH7 ай бұрын
Probably the mount break damage was the same thing that bent all the prop blades
@JPerry23377 ай бұрын
Thank you for sharing your experience. You may want to work on your technique. Put yourself in the place of your audience. This could help increase your viewership.
@johancarlsson76687 ай бұрын
Thanks for the guidance, nog I feel totally comfortable to service my Dt5! Also supercosy with the chicken sound in the background! / Johan
@billwelch94317 ай бұрын
Great review and nice car!
@muzza74898 ай бұрын
How do you replace the fuel tank
@hungnguyen80658 ай бұрын
U have to sale
@dancassidy74718 ай бұрын
Mine doesnt have tgat scrrw
@joemccabe8308 ай бұрын
Asshole....how about doing another video with better sound. I'm def and can't hear a single word but at the end..... that's what I think. Not many videos on these rare stihls 010 av.
@GF-mf7ml8 ай бұрын
People keep saying this is new technology.
@user-uo2pz4xy1o9 ай бұрын
I have a 1937 Johnson LT37 and needing the same two items you stated, ... the handle and the spark plug cover. Would you please tell me where you purchased these from? I would be most grateful if you did. Thanks
@highlandoutboards5 ай бұрын
Go see Doug and Matt Penn's Outboards @ www.oldoutboard.com/
@user-xi8qc2tt5d9 ай бұрын
Elektronika za 7.5 nabavka
@jchristian84139 ай бұрын
brilliant. fewer moving parts
@tommywilliams14029 ай бұрын
I hope you didn’t charge him extra for that air filter because I watched you squeeze the shit out of that air filter and broke it. I never had an air filter be that hard to come off. This is why I do my mechanic work.
@amerlin38810 ай бұрын
Thought maybe I accidentally clicked ahead in the video. Everything presented was correct but would be better if video showed the actual replacement of the new parts. Tip: After the flanged hex steering bushing was removed, I threaded a length of string trimmer filament up the hole until it cleared the engine bay. Put the new bushing on the line and let it slide down to the hole. A little pinky finagling got it seated properly. My old pinion gear only had wear close to one edge so I was able to flip it over and reuse. Fortunate as the replacement bushing was not bundled with a new pinion gear.
@libyalibya119210 ай бұрын
Please where can I get a complete hand control knob for the same engine Can you point me to a place to sell these things?
@DavidDouglasToth11 ай бұрын
Thanks, bud!
@jasper859811 ай бұрын
Does anyone know the correct fuel mixture for these 2 strokes? 1:50 seems to be smoking quite a bit. Should it be 1:100 or 1:50?
@thomasirvin41598 ай бұрын
50 to 1 according to mer c service manual
@jasper85988 ай бұрын
lol your a bit late but ty for the answer.@@thomasirvin4159
@MrRab196011 ай бұрын
Why won't Honda acknowledge this motor exists? All they talk about is the BF5 not THE BADS HP5
@bobach608311 ай бұрын
But what type of grease? Poly?
@zulhilminajmi856011 ай бұрын
makes it sharp
@sgg897011 ай бұрын
Cripes man trim your house wives fingernails! Looks creepy!