6 жыл бұрын
7 жыл бұрын
Пікірлер
@xaviercastilino2848 6 күн бұрын
I have a cooling pad A keyboard and a mouse both with 1000hz polling rate and a keyboard connected piano 🎹🎶
@inkyy829 12 күн бұрын
hello im trying to bridge my keys but the one im trying to activate isnt working like 2pin that activates the key is not acrivating it even if i put power to it is there anyway it can be fixed?
@skiwithpete 11 күн бұрын
@@inkyy829 the keyboard is essentially a grid. If a whole row or column is dead you may need to bridge to the chip. Otherwise if adjacent keys are working there is a way to get your key working again
@kelvinthenedy 14 күн бұрын
Whoa thank you so much, i'll try this! But does the F1 key work afterwards?
@skiwithpete 14 күн бұрын
@@kelvinthenedy if you do it correctly, everything should work.
@kelvinthenedy 14 күн бұрын
@@skiwithpeteThank you very much, oh and does the cable awg matter for the bridge? I have this unused old hdd sata extension cable and i thought maybe it can be use as a bridge? Or should i only use 24 awg cable for keyboard's pcb bridge? thank you again in advance!
@skiwithpete 14 күн бұрын
@@kelvinthenedy whatever you've got I'm sure will be fine. It's very low voltage.
@kelvinthenedy 14 күн бұрын
@@skiwithpetethank you very much
@kelvinthenedy 14 күн бұрын
@@skiwithpetehey there, just want to let you know that my keyboard now worked normally again and funnily enough, it's also the escape key that didn't work and i followed you by welding the left pad with a small cable to the left pad of F1 key and all keys are now fully functional. Big thanks to you!
@Zenavesta 15 күн бұрын
Very cool man!
@HenryOwens-py3ur 29 күн бұрын
Hey Pete, i have the 16 relay and only a Samsung tablet, could i controll each relay on a designated voltage for a 48v lithium battery, nothing to do with the battery it self only to control the relays to close and open on a desired volt, whats the bits i would need, thank you
@skiwithpete 29 күн бұрын
@@HenryOwens-py3ur start with a basic pi and power supply and build your way up. If you look at my garage relay project, I share code in there too that would work to operate from your tablet too. But you gotta get a pi and figure that part out too.
@lunatunny7594 Ай бұрын
hey! you got the key order for mapping backwards. other than that thank you so much!
@thegamechanger3793 Ай бұрын
Where does 8 channel relay come in handy? I’m just trying to understand relay part and where can you apply this in project? Where to? Can someone provide some scenerios?
@skiwithpete Ай бұрын
So a "relay" is just basically an electronically controlled switch. You know, like a light switch, but instead of controlling it with your finger you control it through electronics. So, basically anywhere you have a switch - like lights, or circuits, or devices - you can control it with this. Some examples? I control my furnace with a relay. Lots of home lights, and christmas lights. And check this video out: Garage Door: kzbin.info/www/bejne/pmPEk41vZZKYi5I&ab_channel=skiwithpete
@antzipw2319 Ай бұрын
My space is green and i can’t get it off, help me guyss. Pn + 4 doesn’t work
@타마-w3j Ай бұрын
Watching and loving this in 2024
@Taggames99 Ай бұрын
How do you turn off the keyboard from programming mode?
@skiwithpete Ай бұрын
PN+F9 - which isn't intuitive is it?
@Taggames99 Ай бұрын
@@skiwithpete what do you mean?
@Taggames99 Ай бұрын
@@skiwithpete it doesnt change anything
@skiwithpete Ай бұрын
@@Taggames99 them you should reach out to manufacturer
@deisonic Ай бұрын
Coming here in 2024, still useful 🔥🔥
@skiwithpete Ай бұрын
Thanks!
@kristieson8162 Ай бұрын
Thank you!!!
@PingpongPoof-c3r Ай бұрын
Time ⏲️
@RayeAerinae 3 ай бұрын
i know this is a very old video, but i've had this keyboard for roughly 7 years with the brown switches, and it's the best keyboard i've ever had the privilege of owning. wonderful piece of hardware, it's taken heavy use daily for the entire 7 years with zero issues.
@skiwithpete 3 ай бұрын
@@RayeAerinae I wish they still made them.
@JesusIsTheWay59 3 ай бұрын
My Pok3r Vortex RGB just goes black when I select vortex mode. Any idea why? Every other mode works.
@intelcorei0364 3 ай бұрын
fixed my letter L i jumper it to the letter K thanks also use multimeter guys to be sure
@T_Terablade 4 ай бұрын
the link dosen't seem to be working for me
@valentinrafael9201 4 ай бұрын
If you type on the left side, you should use the right shift, and if you type on the right side, you should use the left shift. That ctrl charged to shift looks painful to the hand. Otherwise, awesome video.
@slugger777 5 ай бұрын
Are these still being made? I would love a case like this
@skiwithpete 5 ай бұрын
@@slugger777 [email protected]
@slugger777 5 ай бұрын
@@skiwithpete I tried to find it on there but could not find this version, only the LCE and metal version. The link in this video just redirects to the root of the site. Do you maybe have a direct link to the product?
@skiwithpete 5 ай бұрын
@@slugger777 email the team see if they've got any left over.
@AsianBoy918 5 ай бұрын
My switch hole has 2 lifted pcb solder holes, any tips or am I doomed?
@VictorDonoso-dz7pw 5 ай бұрын
Bro, help please. In My case when do this, go to inverte, like f5 dont work, and I sold f6 (work) with f5 (dont work), so, when I click f5, go to f6
@skiwithpete 5 ай бұрын
then you made the wrong bridge.
@VictorDonoso-dz7pw 5 ай бұрын
@@skiwithpete So, I do same u made, bro. But, I my keyboard is BlackWidow Chroma. Can I see u a picture to u see?
@skiwithpete 5 ай бұрын
@@VictorDonoso-dz7pw Don't do what I did. Keep trying until you get a combination that works... Mine and yours probably didn't fail in the same way. You could show me, and I'd still tell you to try out all the different possibilities...
@VictorDonoso-dz7pw 5 ай бұрын
@@skiwithpete So, I try with others combinations, I think my circuit board is shorted, u have a tip?
@alexsartorio 6 ай бұрын
Obrigado amigo, do Brasil
@skiwithpete 6 ай бұрын
@@alexsartorio de nada
@adalar42 6 ай бұрын
What a nice review there, so informative. Thanks!
@rianbelgica5990 6 ай бұрын
The key i needed to work worked, but the other keys like alt keys both (L,R) is now nit working ang the windows key turned into alt key help pls
@skiwithpete 6 ай бұрын
@@rianbelgica5990 you've made the wrong bridge if keys stopped working
@xELIMINATORx 6 ай бұрын
I was trying to open the back of my keyboard without realizing that there are 10 screws holding the back in place. I was forcing my way in and damaged the board near LCTRL key. LCTRL key was not responding and I thought I needed to buy a new keyboard but I took a wire and bridged the pin from LCTRL all the way to F12 (had to look for it assuming it's different on every keyboard) and just like that it worked. Thank you sir.
@skiwithpete 6 ай бұрын
thanks for taking the time to let me know 👍
@BeatMachine9000 6 ай бұрын
my pi3+ barely runs 480p
@andrewpr9030 7 ай бұрын
Just fixed my cougar using your video, man thanks so much! PD: if it helps for someone, be sure you are attaching the switch to GND of a switch with the same GND working
@jerich08 7 ай бұрын
my row of left shift to /?key is not working where do i start the bridge?
@skiwithpete 7 ай бұрын
I don't know. Lots of experimentation ahead.
@Noble-BenChukwuma-oz4xt 7 ай бұрын
Can I get the configuration command for the relay switch. The configuration link you drooped was that of alarm setting.
@skiwithpete 7 ай бұрын
I have a couple of relay videos with that code in it. Do a search for skiwithpete relay or I'll try to post links later.
@Noble-BenChukwuma-oz4xt 7 ай бұрын
@@skiwithpete kindly post it. Many thanks.
@skiwithpete 7 ай бұрын
@@Noble-BenChukwuma-oz4xt kzbin.info/www/bejne/hYLcn6eHgcatg7c&ab_channel=skiwithpete
@Asian1Rice 7 ай бұрын
after connecting them together does the f1 key still work?
@skiwithpete 7 ай бұрын
Yes both work as intended
@Asian1Rice 7 ай бұрын
@@skiwithpete thank you mate
@JustFluxz 8 ай бұрын
how well does it get stuck on grime off? the keycaps that I am using haven't been cleaned in years and want to make them clean before getting a new keyboard.
@skiwithpete 8 ай бұрын
this is the way
@JustFluxz 8 ай бұрын
@@skiwithpete hopefully will get the job done. my keys significantly worse than in the video lol.
@skiwithpete 7 ай бұрын
@@JustFluxz I did a video I think called "the dirtiest keyboard in the world"
@AdaMichelleYoo 8 ай бұрын
Thank you so much! I am a total amateur and I was lost, but thanks to you, I know how to install stabilisers now. I like how you make everything simple and easy to understand..the hotel and ground floor analogy is brilliant =)
@skiwithpete 8 ай бұрын
:) thanks for commenting. Warms my heart that my time was useful.
@danialothman 8 ай бұрын
Just fried my Pi. dont ever connect the 5V on the relay board to your Pi. I now use the 5V and GND pin on the relay board to power my arduino, which is receiving serial commands from another Pi I have laying around. The downside is you gotta code twice - use AI to generate that 😅 It was my own fault, I should've tested the power pins on the relay board.
@croaton07 8 ай бұрын
Great video. It doesn't help me as I'm using a B+, but it's still good to learn from.
@skiwithpete 8 ай бұрын
Why don't you think it will help you? Aren't pins the same?
@salskan3121 9 ай бұрын
Ive soldered my spacebar key to my B key and all its doing is just firing spacebar and do you know how to fix this because ive been struggling to understand why its doing this. If you have any suggestions please lmk bc ive been trying to fix my keyboard for months.
@skiwithpete 9 ай бұрын
You've connected the wrong pins. Try different ones.
@salskan3121 9 ай бұрын
@@skiwithpete thank you I appreciate it
@nbacX85 9 ай бұрын
When I use the socket left or right from my broken switch the switch is working again but it triggers the action from where the bridge is coming… what I am doing wrong here? Nice Video by the way!
@skiwithpete 9 ай бұрын
You're connecting the wrong ones. Keep trying.
@nbacX85 9 ай бұрын
@skiwithpete so you mean try more switches to the left or right till it triggers the right action?
@skiwithpete 9 ай бұрын
@@nbacX85 all of it. Try different switches to bridge to and different pins until it works correctly.
@nbacX85 9 ай бұрын
@@skiwithpete interesting ... found the first bridge! Since I have 4 defective ports on the PCB I guess I must fix this one to find the next. thanks for your help so far.
@SHANNU_26 10 ай бұрын
Brother, when i bridge the pin, its picking up the key which i have bridged from. And that key doesn't work. What should I do?
@skiwithpete 10 ай бұрын
change the pins you're bridging.
@SHANNU_26 10 ай бұрын
@@skiwithpete nope i have changed the pins didn't work
@skiwithpete 10 ай бұрын
@@SHANNU_26 I don't know what to tell you. It's a grid. You need to replicate the grid with wires. If you are getting a different letter firing, then you have incorrectly made the grid.
@SHANNU_26 10 ай бұрын
@@skiwithpete ohhhhh yeahhh...so could you tell me now what to do?
@skiwithpete 10 ай бұрын
@@SHANNU_26 try different combinations until it works
@johnwhitehouse3539 10 ай бұрын
Thank you, I needed to know if this thing was configurable befor ei purchased one.
@rancescomaturo5238 10 ай бұрын
Thank you man, you were the only one on the whole internet that helped me with my keyboard, you are a legend
@AmazzzingZEUS 11 ай бұрын
Thanks. I'm watching this in 2024 and it's kind of content I wish I could see more (soldering camera kicks ass!)
@skiwithpete 11 ай бұрын
Thanks friend. Plenty of content with the solder cam for you to check out. And who knows, I might make a come back.
@letmargotcook 11 ай бұрын
Can I ask 2 questions? can I use copper wire without rubber coating? in this case is it better to position it behind the PCB like you did, or in the other side or does it not matter? (to avoid counter-circuits)
@skiwithpete 11 ай бұрын
I mean, if it touches anything - you're not going to have a good day... but if it doesn't, then doesn't matter.
@letmargotcook 11 ай бұрын
it would only touch the pcb, but maybe I'll buy the rubber one to be safer then@@skiwithpete
@Raspberrypi_CNC_Controller 11 ай бұрын
youtube.com/@Raspberrypi_CNC_Controller?si=Mxbt5ZNTwRL6ovxx
@juanmf 11 ай бұрын
Nice, how did you manage to run all of them simultaneously with python? I had to use multiprocess, check this out if you still work with steppers. kzbin.info/www/bejne/jaHVd2Z6rpx1mKc
@ggpall2177 Жыл бұрын
I tried this on my left arrow to my down arrow, but now it triggers the down arrow. How should I fix this?
@skiwithpete Жыл бұрын
You've made an incorrect bridge. Take it apart and try other ones
@ggpall2177 Жыл бұрын
@@skiwithpete Thank you for the help. By the way, I pulled both out both of the pads. Does that make a difference?
@Skateanddestroy99 Жыл бұрын
Could you tell me what material this cable should be made of? Thank you!
@skiwithpete Жыл бұрын
Awg14
@garryhartlin2504 Жыл бұрын
In order for the relay board to work for a Raspberry Pi 4 you must ensure the inputs are active HIGH. Most boards out there are active or trigger LOW. If you have a active LOW board you will need to place a Darlington sink drive ahead of the relay board inputs. Use something like a ULN2803. You will need two of them, cost about $1.25 each.
@bruhnah4life Жыл бұрын
Man how can i fix my column pin its attached to the transistor i think maybe on the top for column, it is kinda broken how can i fix it
@HubertTheMad Жыл бұрын
Thanks for this video! Referred to this because I lifted a pad when desoldering, and I'm more of a visual person. Much love, and happy New Year!
@skiwithpete Жыл бұрын
You too! Congrats on the fix
@RAILGUNSHOOT Жыл бұрын
My F rows of mechanical keyboards don't work, can I connect a cable from the numbers row to F row and it'd work?
@skiwithpete Жыл бұрын
I don't know what you need to connect to where, but yes you can make it work again.
@Andre-qx6bl Жыл бұрын
the bridge work but some time my keyboard key is glitching, amy suggestion?
@skiwithpete Жыл бұрын
You didn't make the right bridge
@Andre-qx6bl Жыл бұрын
@@skiwithpete alright thanks for the reply