Are there many truck drivers that do this? Not sure if I'll even have the time

I can’t get my clutch basket out idk why

Thank you sir, can't believe some e bike or motorbike owners visiting mechanics to get these kind of things done.. like changing brake pads, tires, etc.. save money and time. Self. Repair

As others have stated, use the hex end of 13/16 sparkplug socket. Remove the rubber plug holder from the socket and insert an extension back into the open end (where a sparkplug would go). Removed my wheel today to send off for new rubber. Ordered a 22mm hex socket off the jungle website for install.

Did you have any o2 issues after removing the cat?

I just replaced my pump and everything is working well but I just can’t seem to fit the cover back on. Any tip?

Doesn't know the difference between a "gasket" and a "seal".

Thanks it worked on mine great advice

Will pushing the dirty fluid to the reservoir cause any problems. I know it's not recommended for cars due to possible contamination of master cylinder....

Awesomeness

How where the breaks did they hold up to your standards? Because i'm about to be doing my breaks and thinking of ordering them on amazon just like you did.Or do you think I should go with JP parts for 35 a pop

Set your blocks ON the bead breaker then set the tire/rim on the blocks. Wrap a strap around the tire and the up right to keep it from pushing out. Theres a little angle iron nub welded to the base that would hook the rim on a car tire to keep it from pushing out, it can’t engage with your rim because of the sprocket and brake rotor. They make a rack and pinion style bead breaker that resembles a massive c clamp with a ratcheting handle. Though this style lacks the capacity to do larger car tires it takes up very little space and is a treat for motorcycles tires and small car tires. The rack and pinion style can actually break the bead while the tire is still on the bike.

Great video

So generally you have to drill a hole into the center of the screw first, then tap the extractor into the hole with a hammer or mallet. From there, put a tap handle on and twist it out counter clockwise or throw your drill on the extractor in reverse. I didn't see you predrill a hole for the extractor first. Maybe that was why it didn't work the first time? 🤷‍♂️ this method almost always works.

That looks like an inside outside tire? The tread is asymmetrical, Which way would you mount it?

so great

Where on the right side does the spacer go? Wheel then brake or brake then frame?

its a no brainer clean it put back in the finned aluminun case also cools down the oil temp by 10 degrees and it looks cool and magnet also good idea just replaced the valve train in my 2015 cvo at 33000 km becouse the roller bearings in the lifters failed $ 6500.oo to have it fixed

It looks GREAT........ Can you unplug the old fuel gauge? it look like it does not belong anymore

What no extra wiring for the rpm gauge ?

Ass dumb video

Mine has split shot sinkers crimped on, they work 👍

You put the 2nd rim protector on and then proceeded to use the tire spoon on the wrong side, damaging the rim. That's amateur.

The Yokohama is asymmetrical; I wouldn't want that on my bike.

Americans are weird.

I just installed the 14in but I agree they suck with install, the throttle by wire should be zip tied to the outside

Tem como desativar "arrancar fora" esse sistema que não serve para nada?

Just had the temp light come on my 2015 Harley Ultra Limited, the coolant reservoir overflowed can that be the water pump or the thermostat? These are both stock on my bike

I’d use a snow tire, softer compound.

How can I change the terminals from the cage type to just screw in? My battery is completely dead and the connectors just screw in. Any new battery i can find are all standard cage type and don't fit.

Which tire brand is good on vaquero.

Would the replacement bolts you used work for a touring M8 durby cover ?

Best way to kill the cruise is to use the roll off switch. Twist throttle in opposite direction and it kills cruise.

Be like hitting Mike Tyson with a vacuum cleaner hose. What can go wrong?

Is that main swing arm bolt reverse thread?cant get mine broke loose

Much appreciated keep it up man! 💯

Nice video! Do you feel like you are sitting lower? Like are you legs more bent? I have short legs and on my tippy toes on my fat boy and need something to lower me.

What car tire would replace a 130/80-18 tire? Thank you all :)

plz find another outlet, this isn't it. We want to find solutions to our problem. Not listen to a person that has no one to talk to at their home.

Please supply the link to amazon specialty socket tool for the sprocket nut .

What bars do you recommend?

I RUN 25 PSI TO KEEP MORE RUBBER ON THE PAVEMENT

It's mandatory for hog chapters, probably sell them at the stealership. Lmao

I run Red White and Blue just to stand out in the parking lot.

Terrible video. Let us see what you are doing😮

Did no one notice that he put the old spring in the new piston?

I used Heavy Duty Hoof Nipper to cut the crimped on clamps off- they worked great. The replacement pump kit from Harley is now $518.

Yee Haw You will never go Back. I love it

The plastic piece you took off is slightly oval for adjustment. No need for all this work.

Excellent