North Carolina

Just watched the video looks super good man! What year and trim is that front clip?

You dont have cup holder, come on man.

I have a 02 f350 with the v10 going to do the swap. What year of 5.9 Cummins did you use? What do I have to do to make the transmission shift correctly? I would like to keep mine like you did. Thanks

How did it hold up in time?

Did you have to swap anything in the fuel system, obviously you did but i mean like the tank pump and filters

Nice job bro. Is it possible to get a really smooth/fine texture out of the truck bed application? I have a 16 tundra and I want to respray my running boards because they’re discolored.

Watching from Fl, like the video I'm looking to get into that project.

I know im a lil late on this vid but this thing is comin together so well in these vids. That red really pops and it all looks stock with how well that engine fits in there. Great job man

Very nice build, love the front end. The only recommendation I have is don’t stack rear lift blocks, it’s not a safe practice. Get a lift block the size you need and install it.

Just came across your post, are you still doing these builds? if possible, please send me an email address I can reply to. Thx

Do u still have the motor available?

I would not trust that prop rod .

❤❤❤

Yea mine dont come apart like that wish they did. My f350 part is all one piece and where it says superduty is inlaid in the chrome

So the stock 7.3 torque converter works for the conversion? Also did you update the valve body in the 4r100 to the john wood valve body?

2002 Excursion

Can I have the link to buy the parts for a ford excursion 2000. Is the conversion from a ford 250 to an excursion.😊

Hey man, thank you for your videos. They have helped me tremendously. I have a question, where did you hook the IGN START and START RELAY wires too? Almost done with this thing!! Thank you for any advice.

24v is invalid . Using the “5.9” to generalize Cummins engines is heterophobic . Interstate batteries are the joe Biden of batteries . I thought I was going to learn something other than what channel to block . Sorry for being a hater but a 12 valve is the only engine that deserves the title 5.9!!! After 1997 the Cummins engine died . Vp trash common rail trash . Make Mexico great again 12v swap the world . I have a ve 12 valve excursion with Duralast battery singular battery . No need for 2 batteries . We need to quit with misinformation and the tomfoolery . Sickening

Cummins swapped?

How well did the raptor bond/hold up without sanding?

How has this held up for you?

What is the price for this kit?

What did you do for the air pump? Mine is v10 as well and i need to add pump for my brakes and lockers

Love the build. I am working on my 01 7.3 converting to 06 common rail. I am having trouble connecting lower water hose. What hose did you use to connect to the lower radiator connections? Also just out of curiosity. How did you control the turbo waste gate on your 24v? Thanks

I'm doing a 73 tomorrow. So this helped a bit.

Did you use the factory V10 4R100, or did you use a 7.3 4r100?

2001 f250 Fummins build 1. 120HP injectors 2. New 65.5 mm predator unlimited turbo by turbo time good for 750-800HP 3. New Fleece HD head with 105# springs and larger hardened valves 4. New Fleece Stage 2 push rods 5. New Fleece billet rocker arms 6. New Fleece coolant bypass kit 7. New .20 over Industrial injection coated pistons and rods 8. New Stage 4 colt cam big stick 9. New High flow water pump 10. New Hamilton tappets 11. New aftermarket crank shaft 12. new H bearings throughout engine 13. New oil pump 14. BD intake horn 15. New BD high flow intake heater 16. grid heater delete 17. ARP 2000 head studs- 220,000psi rating 18. New 180 degree dual front and rear thermostat’s 19. New 4 row radiator with electric fans 20. New aluminum coolant reservoir 21. New cam shaft sensor 22. New coolant temp sensor 23. New High flow crank case filter breather kit 24. New vacuum pump 25. New XDP oil squirters 26. Edge juice with attitude cts2 7 levels 27. 2006 Allison 6spd sun cost built to handle over 800hp 28. King ranch interior 29. 4 inch suspension lift 30. 5 inch exhaust 31. TSO 7” exhaust tip 32. Fuel lab. 200 lift pump

What’s your entire build I’m super curious because we have essentially the same setup

You ever figure it out I’m doing mine now and they have a yellowish green tint as well I don’t get it

I know it’s a little late now, but spray you a coat of primer sealer over the bulldog to keep it from bleeding through and reacting to the basecoat

🤍 cool build I live just north of Detroit.. it's a 12 hr Excursion from me to the most Northern tip of the Upper Peninsula Perfect truck for the wife and 4 kids going up north camping or Cherokee NC down your way

hey where did u buy the mounts i couldnt find them thanks

I dunno just askin' crazy or just stupid to yank out v10 in rv to replace w/ Cummins

I'm exploring a 12 Valve P-pimp swap in an Excursion for my wife. Good information about the HE351 making the intercooler piping easier. Thanks. What's the original application for the intercooler?

Kool build love the red accents From Texas

You guys still doing these builds?

Do you still have the 302 motor for sale?

I've watched many of these videos doing a swap and Still have questions ! Here's a List 1. Was the P/S pump from a Hydro boost system, and if not did you have to get a new upgraded one. 2. A detailed visual of how and where the lines run especially to and from the P/S pump. 3. What year model Reservoir did you use and were you able to use the same rod going from the booster to the reservoir ? Thank's for a great video !

This is sick man

I am mouse clicks away from doing this. If you could please answer a couple questions. Looks like you used the stock master cylinder? What year/make hydraboost did you use? Are the lines custom made? Thanks for the videos! 12v in a 2000 Excursion on this end.

Thank you for your video! I tried same coat for my 4runner's side step with splay ver of raptor liner with this video🙋‍♀️ Appreciate from Japan!

Can you tell me where you got those rear rubber spring spacer blocks? Having a hard time finding them for my 2000 excursion.

I’m having these done to my running boards. I have aluminum ones and the paint has gotten flakey

Hi how can I contact you?? I want to convert my excursion and I really like your project thank you

great job las vegas nv i am looking doing a swap also i also have a 2000 excursion v10

Hey man, how do you control the transmission? I didn't see it in the series

Great idea on the drive shaft.

Nice truck! Good job