They make a tool to get them tight you know? $7.99 American.

If Ethan Hunt worked for MI6.

Could have been a 5 second short, but ok thx.

Hey, just wondering if theres a mark to show where the auxiliary shaft should be? And if its a different belt for 1.6 or 2.0L Thanks

Groans in borg!

Thank you .very useful. I will save for my time I finally put back the engine

I got it.💫

zacofany jestes koles, jest specjalny przyrzad do zaciskania tych opasek.

Where's a link for a new cam kit or a mild cam where I can still use the stock timing belt top gear?

I am converting my mx5 with a M45 charger and I found your videos very informative. My car reg. is YF51 JKO !

I caught up to you! I did my full m45 build, similar to yours. According to virtual dyno I'm making about 160 horsepower. I wonder if yours is pretty similar

Great, straight Forward explanation. Will find out if I‘m ready now for my First tune on a triple carb Datsun 🥴😇

Thanks for this video as I don't know what im doing. I'm trying to fix motorbike electrics, as changed loads parts and bike still dead. Is there a test also that makes a beep sound if a break in the loom or just this test more simple for beginners?

Thanks bro. Finally a solution. Works perfectly!

Thank you

Thank you

Just buy the tool mate

Where I can find this shapeways throttle adapter you are using. I have searched the web without any results..😢

Great helpful video, thank you 👍

Vielen Dank, thank you for the TecTip. Helped A LOT

What bad is a stud that is somewhat bent? Thank you

Pickel forks stink and you’re totally right they kill the rubber boots

Thanks a million!

Thank you

Great video, thank you. Good luck cutting that hedge behind you!

How long was the car sitting till you were able to start it after this install

Thanks so much, I just bought a Lotus 7 Replica with twin weber 45 DCOE and have been looking to educate myself on these.

Get to the damn point

Saved me from buying the steel tie tool for a single job. Thank you!

Unfortunately this did not work on my 85 F250 non power steering truck. I turned mine so much the screw wouldn't go back on 😔

What about putting a magnet on the back of the clamp to hold the ball in the back

sorry to spam your comments but my build is finally done! your series here was a huge inspiration even though I used almost none of the same parts. Thanks for walking us through the entire process and making it feel achievable

great series. do you think the power gains from this would extend to a 1.6 nb? i do notice on mine when the engine gets warm that the power seems to drop off slightly

Thanks. Really useful!

Great video, and thanks for sharing. In balancing my 40 DCOE webers, the front 3 are at 5 on the air-flo meter but 4 is at 7. What would contribute to this carb being higher? Thank you!

Perfect timing!

or buy the correct tool

I very much enjoyed and learned from your clear picture of steering box screw, and your clear speaking, and uncomplicated video. As my enthusiastic thanks, buy and try thin inexpensive blue "surgical "latex gloves, their cheap and you will not hurt or cut your hands and fingers, as much, and you will be very surprised. As an added plus, buy white thin cotton " insert gloves " that go on your hands " first ", then on top of the white cotton gloves, go the blue latex gloves. You now will not sweat hardly as much, and it feels much better with them on, and worth the small expense, and you can wash and dry, and reuse. thank you. I especially liked your paint marks of original position.

Cheers for the video, the number of videos showing how to change a driveshaft with a double wishbone is rather limited. Also its far better watching the work being done on an older vehicle with a touch of rust as well.

are the wire colours the same on a mk2 1999 or are they different

Great tip! Thank you.

Just attempted and succeeded on my 2000 SC Miata Finally a factory idle !working that closed loop idle ! Megasquirt pnp

Thank you

Glad you got to enjoy it in the end Your videos are absolutely top tier content. Extremely helpful and easy to watch and follow Hopefully ill get there in the coming months. Trying to keep the budget down in 2024 isnt the easiest Ive also got a faulty me221 ecu 😅

Thank you

My man, needed this

Thanks for posting this. It will be a huge help for me.

Awesome video I was just going to attempt to do my down pipe wrap tomorrow

You legitimately saved me HOURS today, AND my car is running better than she has in a LONG time. Thank you so much!!

fantastic