Top thanks for vídeo

Try some restore and protect valvoline oil. Clean out. Let me know if it helps

Are you high? You c9nfused the shit out if me.

I subscribed for your Honda information. I.e. Visor replacement. However, I happened upon your kayak experience. As a fellow kayaker, good information! I kayaked in the San Juan Islands for three nights and camped on Valdez island. I was surprised at how warm the water was. I wore shorts and Teva sandals the whole time, but of course had layers and jacket rain gear. Thanks for the short video. Super cool.

Thank god these balls joints aren’t pressed in, what a easy job 😎

Amooo gracias

What tool you used to tight the bolt 17 pounds or that

Can U please tell what level should be on a dip stick in transmission?

For some reason, my rubber part of the steam wand is now stuck in the outer part. How do I safely get it out.

Great video made the job so much easier, seeing and knowing the step by step process doing the job. Thank you for making and posting your Videos.

1:20 1:35 1:48

WTF

I can’t install a wheel stud with these

Dude...don't start the video halfway through the repair!!!

Very helpful video

I own this machine and my husband and I both use it daily for the last almost 3 years and it makes a fantastic consistent cup of espresso and or chicory coffee EACH AND EVERY TIME with beautiful creama on top!! I wanted to buy another one and now I can’t find it anywhere I’m so sad!

Pull part off to ensure I could do the job. It should be stiff. Mail ordered part from Rock Auto. Replaced part. One would have to get real luck in order not to have to pull the strut out of the way. The two upper 14 mm bolts were too long for me to get past the spring. The joint was making noise when going over bumps and was like rubber grabbed the joint and moved it around. The joint should be stiff. Good luck replacing yours.

I have Kia Sedona 2009. I smell gas inside the cabin and saw fuel next to the engine. What could be wrong? Thanks

Thanks 😁

Thanks! Had me stumped! 😆

Rust belt tip Use anti seize on all the threads. Thanks for the video.

Honda sunvisors are crappy and so is the engineering of the part to remove it!

Thanks, that slide button is a real pain. This video made things a lot easier.

What code or any will u get with a bad pvc valve?

When this piece is damaged, does it cause a kick in the gear?

The tamper comes out!!

I feel like i'm going crazy. I've watched half a dozen of these videos, and none of them look like mine. There's a big cap that prevents me from accessing the bulb. Seems like i'll have to disassemble the entire front to unscrew it.

Where did you connect the single white wire which was part of the wiring harness in the truck area?

Do you need tp use a coffee grinder

Cooler weather seems to help better, or mowing before sunrise / sundown.

Pad slippers, put on new rotators, clean your contact points, clean your bracket, and take pride in your work. Quality is Knowledge and thar produces understanding. Learn from the ones who have the experience not those looking for clicks. I watched to see how wrong this video is.

I'm doing the same thing, are the two idler pulleys the same part? I bought one but I'm not sure which one, I'll replace one randomly and home it works

Ford: let’s make it as difficult as we can so they can bring it to the car Dealer for any Repair….!!

Great info buddy! I'm in the same situation after changing a corroded brake line. I'll give this a try ASAP. BTW do you still have the car, what do you think of these? Cheers👍

Thank you

Had to do both rear hubs on my crosstrek. I tried at least 5 other techniques and rented equipment. This worked in less than a minute. Instead of welding a bolt, I found a thread adapter(amazon). I couldn't find one long and thin enough so I added a coupling nut (amazon) to that, which also pulled the outer half of the hub off in minute. Then I added in a threaded rod (local hardware store) and used that to do the technique in the video. I only wish I found this sooner 🙏🏽 For the Amazon finds, don't waste your time at Lowe's, Home Depot, and Ace, I did that for you, none of them carry these items in the size needed if at all.

Poor explanation

I think SOA868V9431 works with can intead of plastic bottle

how did you make sure it maintained 2k rpm while the bottle was draining?

After putting new visor my lights are not turning on sir , inside lights

En Espanol: GOOOOOOOOOOOOOOOL (estados unidos).

I was considering subscribing but to help me decide I need to know if this guy is a Kamala Harris supporter

I know this is older. The ECP is just $20-$30 more

I need you in my life!!! Lol

I have a question for anyone that can answer please. I noticed there was not one used in the video. It appears that the hardest part will be near the wiper and getting that area off to access the top part of the strut. I don't need a coil compressor thingy correct?

Thank you for all the details. My instructions walked away, and I can't find them. Somebody they will come back.

Rachet 3'8 or 1'2

Well explained❤

Thanks for this tutorial! Has the replacement mirror light worked?

thank you, now I need to locate the one fuse that's for my dome lights