Great video!!

Nice video. Perfect KZbin content

How is it that out of 7.3K views, you received just 6 comments (now 7)...

Brilliant!

This was so helpful. Got everything fixed up. Thank you!

Got it! Thank you!

From what I've read, "Crescent" made the originals between 1908 and 1916. A cast of other makers followed. They came in 12 and 20 gage with 36 and 40 inch barrels. The "Long Tom" on the frame for Crescents appears to be in fancier script like yours, the rest are blocked script.

Thanks for pointing out the red section of chain goes in front on the RIGHT side of the car/truck. The instructions didn't explain that.

Great video, thanks!

I noticed that you Phil Crockett, that you cranked down on the rings and tighten very tight. Rings are to be finger tip tight. and @Dreemwever made a question comment; "No need to vent Canner for 10 mins prior to placing weight on petcock?" Yes most definitely the pressure canner needs a 10 minute venting before puting weight on petcock. (See canner manual) Phil your video was very good, I liked your idea of blanching the green beans.

Directions unclear, I made a banjo out of grommets😅

Perfect! Lovers 🥰👏🏻👏🏻👏🏻

Super video, instructions are clear and very well explained. I did bearing replacement on my washer following your video and my Maytag Bravos works now like a new one ! Thank you very much !

I’ve always been told to remove the positive terminal first. Is there a reason you removed the negative terminal first? Otherwise great video.

Excellent job. The pauses, lack of music, clear explanation. Great work

Best of the four instructional videos I've watched, no need to watch another, this one was pretty explicit and clear. Thanks.

Thank you from Brazil 🇧🇷

Great teacher!! Thanks

Why didn't they just design it to reach from inside the engine compartment to change it?!!!!

I'm so thankful for videos like this

Is it a good idea to sand the edges after the cut?

This video made so much sense!! It helped me tremendously! I’m way less anxious when it comes to putting chains on. It’s been probably 20 years since I’ve put chains on and I haven’t tried this new kind yet. I just purchased these. Thanks for making this video!

Thank you for explaining this so clearly. I fixed it!

thanks for the help!

Dealing with the exact problem. Flange was in need of replacing. I was trying to figure out how i was supposed to get the pvc out of the pipe. I'm fixing to have a go at it. Thanks!

Lolon a 5 o

Much more of a camping cooker then any thing else. But at that I give it a zero. The old, tried and true Coleman stove is much better. And cheaper.

Way too much work just peel back the wheel well liners

I have used the House on the Hill recipe and video. Yours and theirs are essentially the same with some slight differences. Now that I've seen this, I'll experiment with it next time. I do like the precise way you give instructions, and the tips about moistening the bottoms of the dried cookies, etc. Very easy to follow. Thanks.

Thx for this video, in your case it is a double union. Is there a trick for removing the top portion that is threaded into the PRV?

I work as a janitor. Last night I found that soneone had thrown away a tiny Christmas tree that had a little music box inside. Thanks to your video I managed to get it going again. Thank you so much!

How is your disarmed mode backlit

Thank you, I’m not a handyman but was able to replace my grandparents old toilet handle with a new one with the help of this video.

Thanks getting ready to do it

I am using both plumber's tape and PVC glue for the PVC pipe that goes into the sink wash basin. The old glue sealant wore out after 8 years. I was plunging the sink of hair and stuff and it must have jerked something loose.

JUST PUT THEM IN THE FRIDGE FOR 30 MIN BEFORE BAKING, NO NEED TO STAY FOR 18 H

Having an issue with those plugs I feel… I have an 1/8” gap or so on each tail light on the bed side. Don’t quite understand how they quite adjust but it’s even on both sides - could be the lights but with it being both I’m doubting that. Just a little confused and your video mentioned the “plugs” specifically so thought I’d ask.

Amazing! Thank you, helped a lot

I would recommend avoiding the use of Teflon tape (Plumber's tape) on PVC joins. Because, the water tight seal is between the washer and the attached pipe. If the joint is leaking, inspect the washer and replace if necessary. The reason I say this is because Teflon tape contains PFAS (PTFE/PFOA) - "forever chemicals" known to be toxic to humans. Great job on the video! Not a criticism of your work in any way. This is just new scientific information that has come out since this video was made.

How about is there not ground wire? (Wire that goes in the green screw)

Awesome video! Thank you for sharing your “handyman”expertise!

Very smart 😊

Great video! Thank you. I want to use 8 oz canning jars. Is there a water fill line fir that?

Thank you so much for such a very easy visual to change and replace my Equinox wiper blades

This video is God sent and I've been looking for it off and on for years

That chair is NOT leather, another stupid youtube video.

Thank you fir this video. Do you have a video on cutting round objects like wine bottles? Wanting to cut the tops off. Thank you! 😊

I’m glad I found this. Thank you for showing this. Not ready to give up on my recliner. Still works well just has a big hole in the armrest. Just ordered this product.

Awesome! Thank you, thank you!!! 😊

What size drill bit did you use?