Tape on the barrel isn’t needed, it will friction fit just fine. If not then regular tape can be used to replace the specialist part. The 3d printed dart guider is very annoying and breaks in storage. I have had some success with drilling holes in the shell and threading a paper clip in which the magazine deforms into the correct shape.
@stairway2118 күн бұрын
This was super helpful I purchased the orange one from you guys and I love it so much it’s my favorite blaster thanks for the tips
@stairway2118 күн бұрын
So it’s rock solid
@rickrebouche35411 күн бұрын
Does the blaster have battery undervolt protection?
@lukegoodman58778 күн бұрын
Yes! We only just tested it last Thursday, but the blaster does have a low-voltage cutoff/alarm built-in.
@BubsBunny311 күн бұрын
Who modded it to take talons?
@KingSupreme1258 күн бұрын
BC Foam Flingers
@quasistellar17 күн бұрын
How does the plunger volume on this compare to some popular blasters?
@tomfoolery402417 күн бұрын
do you plan to sell pre modded bk2s's with the talon conversion for those less mod-brained?
@TheRedx64317 күн бұрын
Insert the m lok taps with a little slack and tighten and the taps will turn and fasten as you tighten
@modbust17 күн бұрын
The air brake gasket on top of the hex standoff at the end of the blaster broke on mine. I replaced it just with some fabric as a brake instead, but do you know why it broke?
@CaptainShotgun00718 күн бұрын
Great job Parry! (Hope I got your name right) This was a very helpful overview. What is the stock FPS? Is it low enough for HvZ or can it be modded to hit that 120 mark?
@343a218 күн бұрын
Around 160fps to 180fps dependant on region also if you want to change spring it accepts gel ball blaster springs very well due to its nature of having a gel ball blaster based origins
@lukegoodman587717 күн бұрын
We have not tested every spring we can, However, our Nexus Pro X springs fit when cut down to length. A 1.4 or 1.6 spring and a SCAR might get you to 120 FPS cap
@RookieRogu4 күн бұрын
@lukegoodman5877, you've mentioned that the nexus pro x springs fit, but are there any other compatible springs on your shop? Maybe the Max Stryker or Seagull springs?
@faieruz3 күн бұрын
Trimmed the mag part below, and fits 15 darts now. Thanks!
@frogsbutfrogs18 күн бұрын
are you guys ever gonna sell the bk1s
@lukegoodman587717 күн бұрын
We're considering selling the BK1s, yes. But we're waiting to see how our first batch of BK2s blasters have held up.
@frogsbutfrogs17 күн бұрын
@@lukegoodman5877 for a while, i had seen a bk2 blaster listing, what is that about
@mantic318 күн бұрын
Pretty sure there are already mods for a new mag release that compliments the talon mod so you can use any talons or kodas.
@davecr101218 күн бұрын
The orange cover for the shroud seems like a smart addition, makes me glad I pre-ordered my BK2s from you.
@WordsAreJustNoise24 күн бұрын
Will there ever be a spring upgrade for the return spring so it seals better when you let the prime go.
@andrewh.8363Ай бұрын
I got a unicorn very recently, but it seems as though the screw port for the top rail that’s built into the blaster (not the piece that you snap into place) is too small for the screws that came with it. Am I missing something, using the wrong screws, or is it a blaster error?
@weebwhacker14412 күн бұрын
i had that problem as well, i fixed it by shaving the edges of the holes down with a knife until they fit. hope this helps!
@andrewh.836312 күн бұрын
@@weebwhacker144 I appreciate that! My roommate who’s a lot more of a handyman than myself went in with a drill and drilled out the excess plastic
@koenkooiman1490Ай бұрын
Got my Harrier up to 295fps with the standard 368mm barrel and the 1.6x300 spring, including the sabre internals. But recommend the 450mm barrel as it is much more consistent, way less fps deviation.
@wooohooo103Ай бұрын
I have a question: Previously I had a worker swift which I stored and barely used. I kept the weaker spring in. The plastic deteriorated over time causing cracks which completely destroyed the blaster. Since then I've been wary of increasing any springloads in my blasters including the worker harrier. In your experience, has the Harrier met any structural integrity issues?
@thatgamingprotogen7043Ай бұрын
I’m ordering on of these soon with a crooked cousin as an under barrel launcher
@richardparkes92442 ай бұрын
I wish I could get an orange Seagull from an Australian retailer
@Masterchief-kj2jq2 ай бұрын
Is there a stronger spring i could use in my harrier? I already have the 1.6x300 and metal upgrades with an average of 300fps but wouldnt mind pushing it to the max but seems like no one has really gone farther than that.
@MoreThanBricksАй бұрын
You could, but I definitely don’t recommend it. Your blaster won’t last nearly as long
@badmusicspeakerman2 ай бұрын
how come my slab doesnt shoot? I followed the trigger tuning part but it didn't work
@lucasburrito1012 ай бұрын
I lost my allen key so whats the size of the key?
@TepidLemonadeАй бұрын
It's a 2mm allen key
@bigfootnintendorazr2 ай бұрын
Awesome
@malcolmr83482 ай бұрын
Im not keen on the flared rear design
@OuterCraft2 ай бұрын
Damn, put it together and its not catching...
@skipsnapdoesfish84572 ай бұрын
Does this fit with a retaliator or alpha trooper?
@maybsuperman2 ай бұрын
What would you recommend to do to get it down to 100-110 fps?
@Seththenerfer2 ай бұрын
The weirdest thing I’ve found in my Harrier’s plunger tube after a game was two entire blades of grass
@frozenfade3 ай бұрын
Is this only on the threaded version?
@edgardejesus92553 ай бұрын
This is one of the best blasters available! Weird way to operate, but I love it!
@jakev13413 ай бұрын
One problem I've had in the hobby is measuring O-rings for replacements. Do you have any tips for this?
@trevormallow27883 ай бұрын
Luke in your opinion what is the optimum time for an air seal? I find myself chasing at least 3-5 seconds by 3d printing new plungers until I reach it but I am curious if it's overkill
@anvu272573 ай бұрын
My tips/experience: * I taped several wraps of teflon to the stock rod to prevent it from collapsing, which is a common issue especially after a few weeks of use and abuse. - This also removes the ability to collapse it in to minimize it, but I find that I never use the in between position and if I wanna minimize it for storage I just take the stock off completely. * Do not attach a sling to the stock or hold the blaster by the stock. This wears out the notches (both ways). I was holding my blaster by the stock facing downwards and the stock slipped + blaster fell down barrel first and dented my floor. * Make sure to mark the front of the little priming block that the pump grip picatinny rails attach to (I personally used a silver sharpie). This makes it easier reassemble since you don’t have to test which way is correct (the screws will not attach the lower pic rail if the priming block isn’t in the right direction). * The black nylon/plastic internals tend to leave a black stain on anything they touch (o rings, mags, darts, etc) Regarding upgrade parts: * For whatever reason, the upgrade metal plunger doesn’t allow for slam fire IME. * If you are using the threaded barrel adapter and the upgrade metal pusher make sure to push back the pusher when switching barrels, elsewise when removing the threaded barrel it might take out the metal pusher with it. You’d have to go thru the hassle of opening your blaster to thread back on the metal pusher if this happens. This will also wear down your metal pusher o rings and threads - Unlike the default black nylon internal pusher and rambase being 1 piece, The metal pusher is separate and threaded well into the rambase but can still slip out with enough force (IE if pulled out along with the threaded barrel) * IME the thick black o rings that come with the metal upgrade kit are the best, followed by the upgrade green o rings and then the default o rings. * The upgrade 1.7 and 1.8 springs are slightly longer than the default spring, so don’t store the blaster with them in to avoid compression and wearing down the upgrade springs. The 2.0 spring is the same length as the default spring though.
@brickosaurus22763 ай бұрын
Is it functional without the barrel mechanism?
@FelixstoweFoamForge3 ай бұрын
nope.
@brickosaurus22763 ай бұрын
@@FelixstoweFoamForge okay, thx for the info!
@somethingsomething90813 ай бұрын
Excellent video, thank you!
@desseler3 ай бұрын
These types of springer maintenance videos are really great! I've been needing to open up my Trion and clean it and this is nice to have as a reference for what to check and clean
@stephenjameson30853 ай бұрын
I had sicking problems with all 4 of my seagulls but no big deal i'm a modder and just upgraded the trigger spring had an added bonus of really crisping up the trigger pull with the stiffer spring
@frogsbutfrogs3 ай бұрын
alternatively i just played with the blaster, it wears in over time nd is now perfect
@brianschraner3 ай бұрын
Hey Luke, what's the size of the opening at the front of the barrel shroud (where the barrel exits the blaster). I've read that the 30mm Worker BCAR can fit comfortably in that housing and be slightly recessed in that opening, can you please confirm.
@lukegoodman58773 ай бұрын
Yes, the wider hole at the front of the Harrier is designed to fit around the Worker standard 15-degree BCARs on the 310mm barrel.
@WilhelmScreamer3 ай бұрын
Which battery is this? I got one from the family reunion discoubt way back, would love to replace that oversized battery for one I can actually fit an alarm on
@JamesLeigh283 ай бұрын
I second this! I can't tell which battery it is, is it the one on the listing under the "tighter fit"?
@lukegoodman58773 ай бұрын
This is the Tattu 550mAh XT30 on our site: outofdarts.com/products/tattu-r-line-550mah-95c-3s-lipo
@liangjun243 ай бұрын
No air seal for caliburn?
@Edward-qx9lb3 ай бұрын
😃 *Promosm*
@MikeleKonstantyFiedorowiczIV3 ай бұрын
What is best quality microswitch in this format of size?
@overengineer76913 ай бұрын
There doesnt seem to be anything to hold rail1 and rail2 on. Is this meant to be a press fit?
@TSCPlayzVR3 ай бұрын
Are these permanent or can you detach the adapter?
@othelloperrello66043 ай бұрын
Just got my hardware, working on getting the print together. Wish me luck!
@bigfootnintendorazr4 ай бұрын
Why would I want one style over the other? What's the difference?
@Davethe19794 ай бұрын
Can you explain why you want the different degrees and what do they produce by using them. Thank you
@MrFreefonix4204 ай бұрын
That is a clone of the Sig MCX stock.
@NepDouble074 ай бұрын
A very nice product. Purchased one for my swift. Put a bit of electrical tape on it to help it fit. It was a bit of a pain, but man it's absolutely beautiful. 8° seems to be a sweet spot for a variety of FPS ranges as well.
@user-tp9gh8ec2w4 ай бұрын
where do u get these because i don't see them on the shop