Hi, the paints used in this video were Water based! Thanks, Anest Iwata Refinish!

Hello. The WS-400 would work with most materials. It depends on the material viscosity, for materials of higher viscosity we would recommend you explore the pressure range of spray equipment. Thanks, Anest Iwata Refinish!

This could be the nozzle make sure it is tightened correctly. If issues continue you may need a new nozzle/needle set. it may also be worth checking there is no residue and give everything a thorough clean. Thanks Anest Iwata Refinish!

Hi, We used E4!

@@AnestIwataRefinish Awesome, Thanks.

26.1 PSI, Thanks Anest Iwata Refinish

What nozzle/needle size did you use? And what system? We mix everything by scales in our videos and follow the TDS of the system we are using. We always use both fluid and fan wide open and 2.0 Bar on clearcoats. Thanks, Anest Iwata Refinish.

@@AnestIwataRefinish TY for the reply. Using the LS and WS Supernova Original guns. with a 1.3 . Tamco Paint systems.1st time with these guns compared to my Sata 5000 this has sharp edges and cannot seem to stop running the clear on the corners of the panels. Shop temp at 70 degrees F. Temp of products in the 60`s i suppose in NY. Does the clear need to be heated to 100 f ? I did close up the fan a touch seemed to help but tough to build confidence in this yet. The LS i tried both Base and clear and worked fine just took a little longer for the clear but did not run 75% ovlerlap. TY for the help cheers.

There is a big difference. LS-400 is HVLP so naturally has a slightly larger droplet and is used at a lower pressure. WS-400 Base is compliant, has finer atomisation and a smaller droplet and is used at a slightly higher pressure. So depending on the material you are spraying there is an option for all systems. Thanks, Anest Iwata Refinish

@@AnestIwataRefinish is possible to make ls400 ws400 base gun ? What parts is need to buy?

Great thanks for supporting the brand! We don't have a cleaning video (yet). We would recommend just doing your standard cleaning process. However, Pay close attention to the air cap, atomisation holes, split nozzle and the needle. Use small brushes to make sure there is no residue left in the small hard-to-reach areas. We have maintenance kits for this purpose with a mixture of different size brushes these are what we use! Thanks, Anest Iwata Refinish!

Thank you for the positive comment, we're glad you enjoyed the video!

OBS stands for optimised base coat settings. WS-400 Base (blue air cap), has different configurations for different brands of paint. WS-400 is predominantly used for one-visit base coat applications/ wet on wet! Thanks Anest Iwata Refinish.

All mixed by scale and to manufacturer TDS. Base coat = 20-30 seconds DIN cup no. 4 at 20°C. Clear coat = 15-17 seconds DIN Cup 4 at 20°C Thanks Anest Iwata Refinish

Thanks for the reply - we're glad you found value in this video. Check out the rest of the channel for different topics!

No news on any limited editions yet. Thanks, Anest Iwata Refinish.

We used Autowave 2.0 because we filmed this at AkzoNobel. The Series 2 features multiple recommendations for multiple brands.

Have you checked the pressure? Correct set-up for the material you are spraying? TDS Sheets? If problems persist contact your local sales branch and they will be able to help fix the issue. We hope you get it sorted. Thanks

Also having the Split Nozzle aligned helps with tolerance and consistency. It will not completely change spraying characteristics as some people say 🙂

@@AnestIwataRefinish I'm painting over 30 years...guns were set up as per spec .back using my gti pro lites ...thanks for the reply but selling the 2 guns I bought ...not for me

In this video, we are spraying waterborne. We typically recommend LS-400 for solvent base coats. We have a video explaining LS-400 Series 2 on our channel 👍

Hi @David-rv2fs, you might be getting confused with how many turns out on the fan? The fluid delivery correlates to the nozzle size in use and would naturally change with each nozzle size!

Thank you for your response, what I don't understand in the video is that you make the fluid flow setting 40 50 and on the gun there are the numbers on the adjustment screw 1 2 3 4, so I don't understand how to make the setting 40 50

@@David-rv2fs He's just stating what the fluid output of the gun is roughly, it's not a setting(it is, if you have multiple nozzles). In other words, he's not talking about the fluid adjustment setting or the screw at the back your gun.

@@AnestIwataRefinish Yes, I understood that well

By entech do you mean LS-400? Thanks

More coming soon! Thanks

Hi, @tlhogan1 - We're sorry to hear that, you shouldn't have to spin your air cap to get adequate performance. We would suggest cleaning thoroughly including the splits on the nozzle and air cap holes. Also, make sure that your nozzle and air cap are fitted correctly. If problems persist we'd recommend contacting your local sales branch!

Hi @timpaulstarks136, Yes at some point we will definitely be visiting the W-300 range.

Very good for clear coat. The LPH-80 is one of those spray guns that can handle pretty much anything you throw at it! Thanks

@@AnestIwataRefinish wow that’s great, I was looking for a mini spray gun. I have a Sata x5500 and an Iwata ws400, the Iwata is a night and day difference when compared to my Sata. The clear coat lays like glass and it covers a lot better than the Sata. Now I use the Sata for base and ws400 for clear but I’m thinking I’ll sell the Sata and get a Ls400. I’m looking for a mini gun that I can use on headlights so this will work great.

@@Viewer899 The LPH-80 would be perfect for that, all small intricate work is where it shines! Definitely watch the LS-400 Series 2 video on our channel!

In this video, we were using E4! Thanks!

@@AnestIwataRefinish I have ordered 2 of these beauties 😊

@@glbn6832 That's great thank you for choosing our products! Let us know how you get on!

Hi, thank you for commenting - Series 2 parts are interchangeable. Series 1 and Series 2 are not compatible. Series 2 all have tailored setups, we suggest looking at our recommendation charts to find the best match for the paint system you are using. (There shouldn't be a need to swap nozzles between spray guns) Thanks Anest Iwata Refinish

Clear coat would be WS-400 CLEAR and Base coats would be LS-400 BASE/ WS-400 BASE depending on the product. Thanks

The LPH-80 can maintain atomisation at lower pressures because it was specifically designed for that purpose. All of the different nozzle configurations offer great atomisation. We'd suggest trying different pressure and fan settings and then if needed switch to a smaller nozzle if required! Thanks!

@AnestIwataRefinish thank you! I absolutely love the fine quality of the Iwata brand. Also have your HP-CS airbrush as well.

They are quite different. AZ4 Is a very good all-rounder, It will be good for a range of uses including large and smaller smart repairs. (It is probably one of the most underrated spray guns in our range). If you carry out a bigger range of applications this might be the best choice. The LPH-80 as shown in this video is a master of spot repair, for small and fine work the LPH-80 is the better choice, purely for its atomisation and ability to make the fan sizes smaller. However, as shown the fan patterns up to around 14cm are very good. So it really depends on what you need - Both spray guns are excellent when used for the correct application. Thanks!

It all depends on the repair. The LPH-80 will atomise consistently throughout multiple pressures. You can't go wrong between 1.5 and 1.0 BAR. On this repair, we used 1.0 BAR.

@@AnestIwataRefinish Merci pour votre réponse, je fait de la petite réparation carrosserie smart ou spot repair donc 1 à 1.5 bar est très pratique surtout si le vernis se pose correctement avec des niveaux de pression d'air si bas.

What is a bar ? how much cfm required ? ( US) @@AnestIwataRefinish

@@nixaeagle141 a bar is a metric unit of measurement. 1 BAR = 14.5 PSI. The LPH-80 requires around 2.2 cfm, to operate correctly!

@@AnestIwataRefinish ok thanks , not much then .

You can spray Glasurit with Series 2 - you can check our recommendation charts here: www.anest-iwata-coating.com/en/microsite/

I've heard it's already in the country but waiting for EPA approval and another thing is the digital versions are having issues with the chrome plating coming apart

The 1.2 is a great all round choice. Maybe add a 1.0mm as a different option, potentially just for smaller work.

Thanks for the positive comment!

Is this good for clear?

Absolutely. I’ve got a 1.2 set up in mine and I’ve sprayed 2K high build primer with it, base, clear and also enamels no problem. I adjust viscosity to suit but it handles everything I throw at it. For all small jobs I use this and my Dv1s. I used to have the Walcom ego but didn’t keep that long. It sprayed nice but couldn’t keep it clean enough for my liking. All metallic particles got engrained in carbon despite thorough cleaning.