Any Driving vids?

thats a big knife for the job

Awsome.

Thank you for this video. I really need help! I have this pump that had 10 gauge 3 hot wires and a ground coming from my panel . 2 hots and the ground were directly contacted to the pump while the 3rd hot was wire nutted off to the side. I have since added a sun panel with( 2) 15 amp double pole breakers in hopes to split the power of one double pole breaker to add a 110amp outlet. Only thing is there is no neutral wire. I got the pump working off the 2 double 15 amps but the gfci only the green light came on but had no power to light the heat lamp. Could I add a metal stake into the ground , run a ground to the bus bar then run a wire to the bus bar to the gfci as my neutral wire. The ground is connected to ground screw of sub panel and also the ground wire that was originally connect to pump is also connect to ground screw. Thank you for your help.

Clint. Thank you for your videos. I envy you by all the tools you have. I used to have a complete workshop in my garage when I lived in Maryland, then moved to Florida and gave everything to my son. I just finished replacing the engine mounts. I went with RENN. Maybe later I will will go to semi solid. Total time to replace was about 1 Hr, however, I could have done it quicker if I was a bit more organized. I have a big project list to do and I will be using your videos as a guide. Note: I am also talking to Markski and there is no way I will tackle the FPR. Man, that is a bear. Next is upgrading the coolers to Wagner EVO2. Car is already tune with GIAC and is supposed to put out 545hp. Markski laughed. It is a 2004 X50. My target is 600-650 hp. Looking for a local Dyno. Merry Christmas

hows the felt holding up after a 3 year beating? im wondering if the felt has started to become fuzzy. im debating whether to use felt or car audio sound deadning mats

Did you buy tire changer from harbor freight and you bought that attachment from Lucid ?

2017 Dodge Caravan, check engine light on, traction control light on, P0571 code. The husband replaced the brake light switch (no instructions in the box) but still having the same issues. The husband insisted we take it to the dealer. After much digging, I found your video and it was all in the adjustment. Saved us so much money! Thank you so much! You are the MAN!

What do you think about putting a small dollop of clear epoxy resin over both SMD LEDs so that they only burn the epoxy if they fail? Weatherproof LED strips are fully covered in epoxy or silicone so I don't see an issue with it.

New key added to my X3 M40i 2022, thank you!

Great videos Clint, but sometimes painful to watch. Man, you are old-school in using the tools like me. Since I have purchased electric rachets, etc that makes the job easier. 🙂 Also, there is a video that I was given as I am contemplating replacing the exhaust, where the guy removed the exhaust w/o removing bumper, engine mounts, etc. Here is the link: kzbin.info/www/bejne/fqqwhYGoipuZrassi=qXbOECrl4AxXWGlS I am also talking to Markski about that FPR. Watched your video. I need smaller hands ;-) Great videos and I am subscribed to your channel. Mine is a 2004 X50 Cab with a GIAC tune and about to change Coolers

Clinton you are a National Treasure to this X3M community man. I had to replace my RGB LED and I was dreading having to remove the bumper again. Stumbled on your video this time around. Thank you bro!! Cut my work by a couple hours for sure.

Just met this issue on my 2020 x3m. Just curious will my warranty covers fixing or not? I have CPO on it. Thank you guys so much!

Agreed Clint. I finally came around to having Deejay helping me install the tune on my 2002 996tt. It was great before. It is phenomenal now! Why did I wait so long? It is like I have a different car! 😉👍🏼

Good video man, just finished up my sub panel in the air compressor room. Thanks for the help!

U made a number of horrendous mistakes

Isnt it 450 ml for front differential i have read in ISTA?

Front Diff max. 450 ml in BMW informations ...?

Thank you kind sir for that informative video just got my platform in today can't wait to hang it

K-Seal, AT-205, engine restore, seafoam.

Is there a how to install video somewhere?

I’m getting the drive shaft clunk noise I replaced my bolt to make sure it wasn’t bent but now I’m thinking I have to do the drive shaft bushing like in your other video thanks for all this very useful information you have the most informative videos on the x3m/x4m thank you so much for these vids!

Super helpful, thinking about using these ramps. This helps

one part that had me thinking, did you just contaminate the new oil filter with old oil? away from that your very clear & explicit.

let's go, clint! this is exactly what i came here to find. grant me your wisdom!

Hi, very informative video! May i ask what radiator is that?

From time to time my passenger side window switch was not working. After seeing your video I opend the switch and there where the broken pins. Removed them and everything works fine now. Many thanks and greetings from Belgium. Roger

Money pit!

A Quad triangle socket will also work on these half shafts

just 5 minutes.........?!?!????? come on.......!!!!🤐

Thank you. Thank you.

hi, do you still have a digital copy of the service manual? im planning to rebuild my engine in the near future

your excitement excited me

Very good video. You’re a great teacher.

Why is connector 4 (yellow) on my 99 Beetle filled with pasty oil, what connector is that?

Thanks For Posting the Video

Hey Clint, dealing with this on my '20 X3M as well - any regrets laying the new element over the old? Saves a ton of money doing it this way.

Great Video I would suggest taking the distributor cap of so you can move the shaft to locate the offset slot to locate it in the end of the cam.

always always , remove the top fill screw first, because if you drain it and can't remove the fill plug for whatever reason....well your Screwed, no pun intended.....

Ur amazing

Hi Clint, I have a South African spec 7afe (1995 model) , 180i GSE corolla . The video is a great help, any idea how to check valve guides on this motor ? Please help.

Do you just remove the engine mount bolts from the bottom through the access hole and leave the upper bolts in place?

Great job! How much disassembly did you have to do to drop the oil pan? does not look to inenvoled it seems like a pretty easy straight forward job.

I just purchased a 1996 celica with the 1.8 liter, your videos have been very helpful. Subscribed.

I have the same problem on my 5afe the whole car starts vibrating when ac is on when on operating temp

4afe 2nd generation to be exact

probably didn’t fix your clunking problem either 😅 considering that but was practically glued on there

wow didn’t realize the torque sequence when replacing my differential flange 😬I think I might’ve ruined my diff since it’s acts weird going up and down hills now

I'm not so certain about this repair. Is the correct one for a wood burning box. why cut corners on something that could potentially burn your house down? penny wise and dollar foolish.

Yall really ran flex for 40’ and consider that a proper installation?