Thanks. After many KZbin videos yours is the only one that has shown me the steps I need to follow and the tools needed. And under realistic conditions. (Wife and kids) great video.
@PowerStrokeTechTalkwARod2 жыл бұрын
Hey I really appreciate you coming back and telling me thanks a milly...
@BlakMartinez-ky6bc3 ай бұрын
Thanks for showing your videos
@Pretzelboymn Жыл бұрын
Best video on KZbin for ICP sensor replacement on 03 and early 04 Ford 6.0l powerstroke diesels
@PowerStrokeTechTalkwARod Жыл бұрын
🤘🤘🤘🤘
@paulrodrigues96034 жыл бұрын
You must not be working fast enough. I can hear the Shop Forman calling you out. LOL
@PowerStrokeTechTalkwARod4 жыл бұрын
Lmaooo
@syexplorarconmigo88534 жыл бұрын
She adds an awesome and adorable flavor to Family Diesel repairs bro... greatness there- family man 🤙
@PowerStrokeTechTalkwARod4 жыл бұрын
😉👌🙌
@kevinschmidt9482 Жыл бұрын
Great video. Just did mine yesterday. It had been done before. Whoever did it before did kind of a half ass job and chewed up the harness pretty good. I went through and soldered/heat shielded everything. Glad I decided to do it from the top and not attack it from the bottom.
@michaelchan89154 жыл бұрын
Wow. Memories!!! Usually set a P2285 when that happens. I can't count high enough how many of these I did. I still have my Snap-On socket specifically for this sensor sitting in my box. I get the sensor from the basement while doing the wiring repair up top. I think someone already mentioned it, but there's supposed to be a shield that goes over the sensor and connector for added heat protection. Those always used to get saturated with oil. Another important 6.0 pigtail part number to remember is 6E7Z-12A690-DA. That's the pigtail for the later model year VGT solenoid connectors that always break the cheesy lock tabs.
@PowerStrokeTechTalkwARod4 жыл бұрын
Hell yea!!!!
@FroggyDaGremlin3 жыл бұрын
Just did mine today on my '03....well my nephew did while I watched. Your vid was a big help. Also watched Diesel Tech Ron do one but he did it from below and that way looked too hard. The hardest part is getting the new sensor started in the hole. He finally put a short piece of rubber hose over the end of the new sensor to give something for his big meathooks to hold on to. Had to position match the new pigtail wires as the colors did not match at all.
@PowerStrokeTechTalkwARod3 жыл бұрын
👍👍👍
@pricechenault26074 жыл бұрын
I did mine about 10 years ago from underneath. Seemed less intrusive at the time, but it was a PITA! Had I seen a PTT video I would have done it from the top.
@PowerStrokeTechTalkwARod4 жыл бұрын
Thanks for watchin pal!
@smokeskull4 жыл бұрын
If the torque converter bolts were not so crazy hard to get in and out it would almost be as fast to drop the tranny
@PowerStrokeTechTalkwARod4 жыл бұрын
Bro that job can be done before you'd even have the trans out 🤭🙌
@adamschmidgall71972 жыл бұрын
Followed your video to fix my truck yesterday. Had a heck of a time removing the electrical connection because the tab was on the back and the space was small. I finally used a coat hanger hook to slip behind it. It came right off. Used then same coat hanger to guide the socket into position with the new part. Putting the new electrical connection on was difficult with the space, but finally lined it up correctly with a long screwdriver through the wires and it popped right on. Thanks for the video.
@PowerStrokeTechTalkwARod2 жыл бұрын
Hell yeah
@joshuakeys4117 ай бұрын
Just dropped a Sub cause you made it look simple with no BS Love my 6.0 but always annoyed at these little things
@donniephares5978 Жыл бұрын
Dude you are the man I love the way you work on The diesels all the way around man I have a 6.7 I started following your channel I also have a 6.0 and a 7.3 and you know I’m all keep up the good work dude
@ricardorodriguez-se7tp4 жыл бұрын
Arod the first time i did one on a 03 i told the guy yeah its fast it should take 5 min boy was i wrong and i told him the price already. It was a Beautiful 2006 King Ranch with a 03 engine couple months later it was stolen and stripped down it was sad. Keep them videos coming
@PowerStrokeTechTalkwARod4 жыл бұрын
Wow! Thanks bud 👍👊💯
@hibrad20054 жыл бұрын
Ooof that coolant hose collapse, there's some intense vacuum in there, bro needs a new degas bottle cap.
@kenhartford39593 жыл бұрын
I'm getting ready to do mine. I was told to unplug it and see if it starts running better, after watching the video there's a lot to take a part and put back together and then replete
@PowerStrokeTechTalkwARod3 жыл бұрын
Yea no bud, just replace it.
@waynepainter3000Ай бұрын
Very helpful. Too bad i dont have the one on passenger side. Looks like my day about to get interesting. Yayyyyyyyy!
@PowerStrokeTechTalkwARodАй бұрын
Gravy buddy
@stevenfuchs25484 жыл бұрын
Ahhhhh A PTT video in the morning, smells like victory!!! Great vid Brotha! made my day.
@PowerStrokeTechTalkwARod4 жыл бұрын
Lolol
@shabobo2215 күн бұрын
Really helpful! Thank you!! I’m new to the diesel truck scene and essentially to owning a truck. Anyway thank you. Definitely helped!! 🤘🤘🤘
@PowerStrokeTechTalkwARod15 күн бұрын
Ayeeee, welcome
@jcobra0911 ай бұрын
Can’t wait 😳 ordering new Motorcraft sensor and pigtail now. Any other advice or things that are good to do while in there don’t hesitate to let me know lol thanks mang
@DaleRobertson-l2qАй бұрын
Awesome did mine while watching you do yours very informative and made it easy thanks man
@niceguy49284 жыл бұрын
They’re my first favorite. I have raised 4 kids on them .
@905Jerrod8 ай бұрын
That coolant hose though !!!
@117tyler3 жыл бұрын
Thanks! I'm going to be doing this on my truck tomorrow
@PowerStrokeTechTalkwARod3 жыл бұрын
Good luck
@chiefin36154 жыл бұрын
Had to work on an 03 6.0 for the first time 6 months ago, same repair except it was my first time seeing an early build 6.0 and it kicked my ass because I didn't have a short enough socket. That night I went home and ordered a socket just for it, real nice skinny shallow socket in 3/8 drive. Of course still havent even seen an early build 6.0 since.`
@PowerStrokeTechTalkwARod4 жыл бұрын
Omg...😔🤭
@68greengoat3 жыл бұрын
Great Video, I am getting ready to do this to my truck, have you you ever seen the remote install kit for the ICP, that re-routes it to the top side of the engine. Read good reviews on them, but wonder what your thoughts were and if you had seen or install one of these kits....... Keep up the good work
@PowerStrokeTechTalkwARod3 жыл бұрын
Never seen it. ICP repairs are childs play...
@gnarlock39273 жыл бұрын
Good video it helps to be able to visualize where that puppy’s at lol. Those Milwaukee Ratchets are the beez kneez
@PowerStrokeTechTalkwARod3 жыл бұрын
I love em!!!
@jacobsilva89784 жыл бұрын
Just went and upvoted every video. Love your stuff man
@PowerStrokeTechTalkwARod4 жыл бұрын
Thanks brotha. Share me around! 👌
@mcool45874 жыл бұрын
six ohhhhhh! My fav. Arent you glad they moved those to the valve covers on the late 04's?
@PowerStrokeTechTalkwARod4 жыл бұрын
Oh yes yes. Dont care too much for the rexroth pumps tho
@nbrowser4 жыл бұрын
Soooo...new Super Duty...part time camera person, A-Rod is movin on up I see!
@PowerStrokeTechTalkwARod4 жыл бұрын
😭😭😭👌
@markmaldonado96142 жыл бұрын
you make it look easy my friend excellent job wish we had a good mechanic out here in el paso tx im going to do it myself thank you for the guidance peace my brother
@thelockoutman Жыл бұрын
He didn’t show up putting it back in. Taking it out as easy..
@PowerStrokeTechTalkwARod Жыл бұрын
Why, you can't just screw it in? I would have figured you all could have connected the dots.....
@bryanosborne3853 Жыл бұрын
@@PowerStrokeTechTalkwARod This helped me get it out but I cannot get it lined up to screw it back in. I cannot get my hand in there to place it. Looking for tricks and tips!
@gaymondavis95814 жыл бұрын
really enjoy your videos other than me you are the one i would want working on my truck lol. good work
@PowerStrokeTechTalkwARod4 жыл бұрын
Thanks brother 👍
@jesusmartinez4675Ай бұрын
Is that the Milwaukee 3/8 ratchet? The red looking tool? That thing is sweetttt! I need one
@PowerStrokeTechTalkwARodАй бұрын
Yes
@gerardobemcomo2706 Жыл бұрын
WHAT I WANT TO KNOW IS WHAT CAMERA YOU USED FOR THIS VIDEO!!! THIS IS ONE OF THE BEST QUALITY I HAVE SEEN!!!
@PowerStrokeTechTalkwARod Жыл бұрын
Cellular device pal
@gerardobemcomo2706 Жыл бұрын
GALAXY S23, I PHONE? WHAT resolution?
@PowerStrokeTechTalkwARod Жыл бұрын
S21 & iPhone Pro max & goPRO 10...4k 30fps🫡🫡
@outdoorsadrenaline2 жыл бұрын
The belly of my 03 looks just like this one in the video and the check engine light came on Sunday shortly after changing out my oil. Hooked up my forscan and it says low icp voltage detected. I’m thinking this repair is in my immediate future. Thanks for giving me a clear understanding of what to expect! Was the connector bad that you replaced or did the new icp just have a different connector? Thanks again for helping all of us out much appreciated!
@PowerStrokeTechTalkwARod2 жыл бұрын
Yes sirrr, you bet. You have 2 replace it because the sensor pigtail is all shorted out with oil & would cause a circuit related issue.
@outdoorsadrenaline2 жыл бұрын
Makes sense thanks!
@outdoorsadrenaline2 жыл бұрын
So I replaced my sensor and my truck is no longer having this problem. Thanks again for you sharing your knowledge it helped out greatly! I did opt not to replaced the connector. Upon inspection it looked okay though was saturated in oil. I sprayed it out with some electrical cleaner then blew it out with my compressor a couple times, added a bit of dielectric grease and didn’t have any trouble with it. The sensor itself was shot. Had cracks on plastic base where the oil was seeping out and with barley any pressure the the sensor plug end snapped right off. Thanks again!!
@PowerStrokeTechTalkwARod2 жыл бұрын
Thanks for coming back & keepin it reall💯💯
@tamaranichols68213 жыл бұрын
about to do this repair. video was helpful
@PowerStrokeTechTalkwARod3 жыл бұрын
Thanks pal!
@nicolenikki96417 ай бұрын
I just put a new wiring harness in my truck and I have that plugged in to the center where is that other plug go
@PowerStrokeTechTalkwARod7 ай бұрын
What
@steves74582 жыл бұрын
You can use either ICP sensor. The only difference is KOEO voltage which is only a few tenths.
@kenhartford39593 жыл бұрын
Should I change the ICP and the the valve next to it at same time just to be safe?
@chrismarichalar79194 жыл бұрын
there is actually supposed to be a heat sleeve that slides over the icp sensor I have been trying to find an oem one for my truck
@PowerStrokeTechTalkwARod4 жыл бұрын
Yea them are hard to find. Prolly an international number
@BarnStangz4 жыл бұрын
"I'm fixin' a truck!!!" damn kids, always ruining the videos, lol, ask me how I know... Nice repair man, tough working on the weekends too, but you do what you do for the good cash paying customers!
@PowerStrokeTechTalkwARod4 жыл бұрын
Gotta keep my fleets on da road TWENTY FOUR SEVEN!!
@ianquinn59163 жыл бұрын
When you discovered oil leak on back of valley after changing icp sensor... what did that end up being??
@PowerStrokeTechTalkwARod3 жыл бұрын
You can go back and watch the video and find ou, that was the whole purpose of making the video to show you where the oil leak was
thanks, for the helpful video about to get into mine.. Wasn't looking forward to going from under the top side looks so much easier
@PowerStrokeTechTalkwARod2 жыл бұрын
Gravy broski!!!
@myleshansel79504 жыл бұрын
Question, could you have just cleaned the pigtail connector instead of replacing??
@PowerStrokeTechTalkwARod4 жыл бұрын
Yea, but the oil makes the insulation so squishy and the thing never winds up sealing correctly again...
@Graveltrucking4 жыл бұрын
I don’t have small hands big meat hooks can be a curse lol. I’ve had to change the icp sensor on my 05 it wasn’t puking oil just stopped working.
@PowerStrokeTechTalkwARod4 жыл бұрын
Thanks 4 sharing
@edgarjacob70203 жыл бұрын
Mine stopped working while running wondering if it can be this it’s cranking but won’t start
@PowerStrokeTechTalkwARod3 жыл бұрын
Naw prolly not
@jeffreyharrelson50442 жыл бұрын
How did you get your ipr plug to face straight up? Mine if fasting towards the heat shield?
@PowerStrokeTechTalkwARod2 жыл бұрын
U can put ur aocket half way on & use it to turn the solenoid np
@98fishingfool Жыл бұрын
I’ve gotta 05 6.0 with 180k, it just started having a strange miss at idle only when warm, doesn’t have issues hesitating or taking off just miss/rough idle. Any idea ?
@PowerStrokeTechTalkwARod Жыл бұрын
Sounds like an injector to me
@DS-TRUCKS4 жыл бұрын
These home videos are great!
@PowerStrokeTechTalkwARod4 жыл бұрын
Thank buddy boi
@dustyklein30263 жыл бұрын
Doing it this afternoon. Looks too easy!
@PowerStrokeTechTalkwARod3 жыл бұрын
Gravy
@GiediPrime1003 жыл бұрын
Excellent vid! Gonna use ur method for my excursion. Thanks
@cleanexwindowsgutters11533 ай бұрын
Did this and i cant find it... Major pain in the ass.. your video was good.
@haleyy684 жыл бұрын
On my 3rd ICP sensor. 03 6.0. 285,000 still going strong
@PowerStrokeTechTalkwARod4 жыл бұрын
Woo woo👊👌
@robertdilullo67652 жыл бұрын
Do you still have the truck?Mine has 326,000.
@haleyy682 жыл бұрын
@@robertdilullo6765 Yes 310,000 still runs great
@robertdilullo67652 жыл бұрын
@@haleyy68 Mine still works great. How long can these 03 last?I'm considering a new bed.Rails and back fender a little rusty. Everything else looks good.
@jonahc418 Жыл бұрын
How much would that cost the customer? I just got a quote from my diesel mechanic and I wanna make sure I ain't getting to screwed.
@smokeskull4 жыл бұрын
You fail to mention the expensive green oring on the vent hose that always grows 2 sizes when u pop it out
@PowerStrokeTechTalkwARod4 жыл бұрын
Duh...i totally did. I have found ac orings work great!!!!
@samwarren71322 жыл бұрын
Thanks for the video, I was able to DIY this and some some money!!!!
@PowerStrokeTechTalkwARod2 жыл бұрын
Yeah baby
@antf0eknee Жыл бұрын
Was there something wrong with the wiring or plug that needed repaired? Or do you replace it anyway?
@PowerStrokeTechTalkwARod Жыл бұрын
Yeah man, it had oil in it.
@hisomething57103 жыл бұрын
i got a f350 04 6.0 and it fires up great. when driving i’ll try to accelerate and it’ll end up stalling at 20 and 60. then i have to take my foot off and push down again, what do you think the problem is?
@PowerStrokeTechTalkwARod3 жыл бұрын
I need 2 put the computer on it....
@gofish23932 жыл бұрын
My 03 did that about a week after I bought it off a guy. Took it to the dealer and they said hfcm and new fuel lines. $3500 I dropped the tank and found the strainer on the pickup line was busted off and pieces in the lines. I replaced the strainer, filters. Blew out the fuel lines and cleaned the hfcm. Ran great until yesterday morning after a really cold start it started puking oil from somewhere on the back of the engine... hoping it’s just the icp.
@MrEzplay Жыл бұрын
What is part number for the pigtail harness, thanks, I wish we had good mechanics here too
@PowerStrokeTechTalkwARod4 жыл бұрын
You guys need to check out this playlist when you get a second!!!!! FORD 6.0 Liter Diesel Repair Videos: kzbin.info/aero/PLO4T4Ez-ZZaQkthM2pSuol5lAFvdXFnGG
@justinbutler15922 жыл бұрын
Thanks for the video I've yet to find any help on exactly what my problem is hopefully you can help with some suggestions. I have an early model 03 super duty and I just recently had another motor put in it issue is the new motor is out of an 04 which was actually in a f-450. Motor is in the truck and running sounds good at idle but driving down the road it lacks its power and sounds as if the turbo is not winding out as it should. I've also come to notice that the ICP on the new motor is not plugged in we're now it is located on top of the passenger valve cover and I guess on my old motor it was down below the turbo the back side of the motor such as the one in your video. So am I screwed because the sensor is not plugged in I have the original wiring harness on the truck and computer is there any way that I can find the original plug and extended over to the valve cover? I have a feeling this is why the truck is lacking its power because this sensor is not plugged in
@PowerStrokeTechTalkwARod2 жыл бұрын
U buddy are not in a good spot
@robz3553 ай бұрын
If this was neglected for a little while, would it cause a misfire tick and then white smoke when you turn the key over and it starts? I bought a 04 6.0 noticed the oil leak on the back of the block and it “loop “ at idle but not in drive..also if this is bad and neglected would it cause more damage to the injectors since now there is white smoke immediately upon start up SORRY SO LONG but thanks if you could help
@PowerStrokeTechTalkwARod3 ай бұрын
No it would not usually
@robz3553 ай бұрын
@@PowerStrokeTechTalkwARod thanks for getting back to me, so probably injectors crapped out too . Either way I’m replacing this. Thank you again! Prefect step by step video
@bradwiebelhaus70652 ай бұрын
Great video.
@jonathanimes1943 Жыл бұрын
Great video, however my hands wont fit , I can barely touch the connector let alone undo it. Im gonna have to hire a elementary school kid to get in there 😂
@tomwiggins12252 жыл бұрын
Why is it necessary to replace the connector?
@jett-rampartflyer28522 жыл бұрын
They say because the insulation/rubber/silicone gets soaked with oil and never seals right again
@rodndrone11983 жыл бұрын
The socket you are using is is like a short deep socket. My deep socket seems almost too long and my short is definatley too short.
@rodndrone11983 жыл бұрын
What socket are you using?
@PowerStrokeTechTalkwARod3 жыл бұрын
A chopped down 27mm
@rodndrone11983 жыл бұрын
Thank you for the response. I was able to use my full size deep, but i had to use a pipe to bend the heat shield slightly back, it was still a tight fit. If another one rolls into the shop I'm definitely gonna make a custom socket. Thanks man
@PowerStrokeTechTalkwARod3 жыл бұрын
U bet
@tctwg14 жыл бұрын
I hate bringing tools from work to home to work on stuff. I always forget something lol.
@PowerStrokeTechTalkwARod4 жыл бұрын
Right!!
@jonesfarm1836 Жыл бұрын
Hey Arod quick question! If you don’t have foil tape like you mentioned in this video could I wrap it up with some Tin foil (aluminum foil)? May be a dumb question idk. I replaced the ICP along with the pigtail over a year ago (sadly aftermarket part 😅)and it’s starting to go bad I believe. But this time I ordered the exact part you used in the video Ford OEM. I hope it will last much longer. Also prob 2-3 years ago I had to replace the IPR but I did buy Ford OEM to replace it so far it’s been fine. 2004 F250 King ranch 🤙🏻😊
@PowerStrokeTechTalkwARod Жыл бұрын
Yea, i suppose you cld!
@donsoffroad28954 жыл бұрын
I'm getting ready to do mine
@PowerStrokeTechTalkwARod4 жыл бұрын
Do it
@edthatch33682 жыл бұрын
Is this sensor on the front of the passenger valve cover also?
@PowerStrokeTechTalkwARod2 жыл бұрын
Yes, very good.
@jonesfarm1836 Жыл бұрын
Yeah the newer style 6.0s are. I think from 04.5 to 07
@CODRAMPAGE100 Жыл бұрын
Hi, my 6.0 ICP keeps blowing O rings. Prior owner said he replaced the ICP and IPR. Iv put on 3 ford OEM 14mmx2mm ICP o rings just to have it blow out again. Any advice?
@PowerStrokeTechTalkwARod Жыл бұрын
Blowing o-rings..... i dunno man. Youll have to email us.
@mattlacarra2069 Жыл бұрын
You might have a crappy knock off ICP. The cheap ones have a gap between the threads and the o-ring. Last maybe 3-9 months I hear.
@franciscojaversaucedososa633310 ай бұрын
Thank you very much.
@bodiesillem10415 ай бұрын
What happens if I have a no start, unplug this sensor and then it runs fine. Can I just leave it unplugged and deal with the check engine light for the time being? Thanks
@PowerStrokeTechTalkwARod5 ай бұрын
That's not gonna make it start pal.....that's ONLY if the sensor is messed up..
@bodiesillem10415 ай бұрын
Well something ain’t right then cuz that’s literally what happened. Truck no run. Unplug sensor. Truck run
@rylanfalcone8452 жыл бұрын
Thank you!
@williambrown672110 ай бұрын
I have a 2003 F-350 powerstroke super duty 7.3 liter once I start my truck up and put it in drive gear and pull out of the driveway!! Drive about a half a block away once my transmission warms up it stops pulling do you have any input on what may be causing this to happen?.. I have done so much research on this problem but no one knows anything! Please reply back...thank you so much!!..
@rylanhendricks55533 жыл бұрын
About how long do you think this took you?
@PowerStrokeTechTalkwARod3 жыл бұрын
Me? Or average joe......
@isaacolivo41173 жыл бұрын
@@PowerStrokeTechTalkwARod both
@PowerStrokeTechTalkwARod3 жыл бұрын
Me 20 min...average joe....long time
@AmericanRustWorker33692 жыл бұрын
Easiest repair I’ve ever done was tell a customer if they want a reliable vehicle without constant repairs, don’t buy a ford , 😂 I work on that junk brand daily but the modules on fords are way better than chevys any day
@shannonlochard71162 жыл бұрын
So can the pressure sensor cause the oil leak?
@PowerStrokeTechTalkwARod2 жыл бұрын
.....that is why we changed it here
@tobbystransmissions60464 жыл бұрын
, nice job.
@darkenfly324 жыл бұрын
Quiet on the set! How am I suppose to work under these conditions? ; )
@PowerStrokeTechTalkwARod4 жыл бұрын
Wheres my leading lady..!?!?
@jasonhusby4802 жыл бұрын
What’s with the collapsed radiator hose?
@oscaratkins81652 жыл бұрын
Can u help me I have o4 f350 6.0 Wire on old color is not same as new plug in how do I wire it
@PowerStrokeTechTalkwARod2 жыл бұрын
U match the wire terminals from the old one. Color does NOT matter
@gunpornstar83792 жыл бұрын
Great video! Ty!
@crandallscooking6 ай бұрын
Will this fix my dreaded, start and run for 2 minutes then just stalls?
@PowerStrokeTechTalkwARod6 ай бұрын
Most likely not
@crandallscooking6 ай бұрын
@@PowerStrokeTechTalkwARod thank you. I had a "shade tree mechanic " tell me it was the fuel relay, which is hard wired to the fuse panel.
@PowerStrokeTechTalkwARod6 ай бұрын
@crandallscooking what a goof he is. Don't take it to pepbous they'll tell u it needs a mass air flow sensor
@crandallscooking6 ай бұрын
@@PowerStrokeTechTalkwARod 😂😂😂
@donniephares5978 Жыл бұрын
Hey dude where are you located man
@PowerStrokeTechTalkwARod Жыл бұрын
Detroit
@rebeccarobinson70243 жыл бұрын
Plus it just cranks and and shows no oil pressure until you get it to start and if u hit the fuel pedal shows oil pressure till u let off then stops working is that the icp bad new to diesels
@PowerStrokeTechTalkwARod3 жыл бұрын
No, icp does not control gauge!
@rebeccarobinson70243 жыл бұрын
@@PowerStrokeTechTalkwARod ok anyway I can send video of what it's doing I'm on Facebook name is rian Robertson picture of a girl beside a horse I'm Rebecca husband we use same email lol
@PowerStrokeTechTalkwARod3 жыл бұрын
What do i need video for..
@isidrogarcia98513 жыл бұрын
Did you get the connector from the ford dealer as well, if you did what’s the part number
@PowerStrokeTechTalkwARod3 жыл бұрын
....did u not watch the video......
@gerardobemcomo2706 Жыл бұрын
Well if you would have seen the video you would have found your answer 😉 6E7Z-12A690-DA here you go just like many other citizens like to be handed things.
@3374jj4 жыл бұрын
Yes.... Trade it for an 05
@TommyHolidayTHEONE3 жыл бұрын
is there a way to connect correct wiring if you can't position match them? I had to yank the wiring out of the sensor so position matching is not possible anymore :(
@PowerStrokeTechTalkwARod3 жыл бұрын
Yea ud need the wiring diagram
@TommyHolidayTHEONE3 жыл бұрын
@@PowerStrokeTechTalkwARod thanks for suggesting that. led me to this diagram www.powerstroke.org/threads/icp-broken-wires.213845/#lg=thread-213845&slide=1
@cadenmoore7573 жыл бұрын
Looking at a truck currently and he says the truck needs the icp sensor cuz it won’t start could this be a sensor that makes it not start
@PowerStrokeTechTalkwARod3 жыл бұрын
Ummm no. The ICP sensor is only the eyes to the computer. Truck will start weather or not icp is connected or not
@demitrioushicks4664 Жыл бұрын
Hey does the socket* size for the sensor vary? Im having trouble taking it off
@PowerStrokeTechTalkwARod Жыл бұрын
The bolt size....
@mattlacarra2069 Жыл бұрын
You might have a newer style. I’m pretty sure it’s a bit smaller.
@demitrioushicks4664 Жыл бұрын
@@mattlacarra2069 i got it it takes a icp socket, long enough to catch and not get cought on anything. Thanks u guys
@mattlacarra2069 Жыл бұрын
@@demitrioushicks4664 there are two sizes of this sensor. There’s the 3C…….. part number for the 2003 and early 04. It’s a 1-1/16” or 27mm. Then there is the 4C…….. part number that’s intended for the late 04-2007. It’s a 15/16”. Both will work on this model year, but the 3c…… is the intended part number.
@billgroel44633 жыл бұрын
Thank you for sharing
@js90142 жыл бұрын
I can’t fit my hand into the space to disconnect the pigtail any recommendations
@PowerStrokeTechTalkwARod2 жыл бұрын
Long pick, long flat blade....
@davidmehaffey91344 жыл бұрын
Cant get my hand in there to get it started back on . guess ima disconnect turbo exhaust
@PowerStrokeTechTalkwARod4 жыл бұрын
Omg, fer realll...uggghhh
@BuschBlackyLight4002 жыл бұрын
Do you need to disconnect the batteries?
@PowerStrokeTechTalkwARod2 жыл бұрын
Absolutely not
@gerardobemcomo2706 Жыл бұрын
You're better off if you do. Or use fender protectors/towels that way you don't run a risk of arcing with your tools.
@adrianspeeder4 жыл бұрын
What does the ICP sensor do?
@PowerStrokeTechTalkwARod4 жыл бұрын
A pressure reading sensor to the pcm
@michaellevenduski72632 жыл бұрын
Does it tell u which wire goes to . It looked different colors
@PowerStrokeTechTalkwARod2 жыл бұрын
No, u match up each wire 1 at a time. Its only 3..
@michaellevenduski72632 жыл бұрын
@@PowerStrokeTechTalkwARod it dont matter which is which then. To me they looked different colors, thats y i asked
@PowerStrokeTechTalkwARod2 жыл бұрын
Mike, follow the video, i show u everything..............
@jonesfarm1836 Жыл бұрын
Look at both connectors and just cut and splice one wire at a time. Just have to make sure that you splice the correct wire in relation to where they are pinned into the connector. If that makes any sense. It does in my head anyway 😂
@Kanesgarage2 жыл бұрын
What do your charge for this repair?
@PowerStrokeTechTalkwARod2 жыл бұрын
U can email me...
@justingomer43712 жыл бұрын
How do you get the plug of right in front of it??
@PowerStrokeTechTalkwARod2 жыл бұрын
A swing tab..
@gaymondavis95814 жыл бұрын
Hello have a question not really related to this video but more to diagnostics on 6.7. If vehicle is scanned with IDS with no codes present and no issues. Is it possible to tell condition of EGR cooler DPF filter and other costly items to get ahead a a pending failure or issue.
@PowerStrokeTechTalkwARod4 жыл бұрын
Ehhhhh possibly. U cld watch all the data & see if its middle of the road or about too....
@gaymondavis95814 жыл бұрын
Is there any info out there as to what is supoee to be normal as far as back pressure egr temp dpf soot load for a engine with a giving mileage .
@PowerStrokeTechTalkwARod4 жыл бұрын
No not really. Ford has reference values to compare to
@joshuamoore24_72 жыл бұрын
It was easier with long arm to put the ICP sensor in from the bottom.
@georgesipes5411 Жыл бұрын
Let's see how to line it up and plug it into the ICP