1 YEAR REVIEW!!! SPE MOTORSPORT CAT FUEL FILTER SYSTEM!! 2017 F-350 POWERSTROKE!

[@myboymccoy9944]

Cat makes 2 smaller filters that are about 3” shorter. Swapped out and don’t hang any lower than the old plastic shield. Cat FF 1R-0750 Cat WS 175-2949

[@kvboyd]

Ordered my kit yesterday

[@luistorresdiaz1274]

Muchas gracias por tus videos hermano, te quiero

[@PowerstrokeRick]

Thank you for the support!!

[@willb7975]

Rick, hit your other video of the SPE Fuel Filter install earlier, asking this question. Have you noticed any difference or did you take any pressure readings of fuel pressure with OEM filters and then post-install of SPE's kit? On the fence, obviously with other competitors out there. Thanks for keeping the 6.7 community aware with your videos, keep them coming.

[@PowerstrokeRick]

Thanks for watching and much appreciated! I haven’t dived deep into anything like that!

[@PowerstrokeRick]

I would say it’s worth it 💯 no more mess in the engine bay and makes fuel filter changes a breeze

[@talonpilot]

The thing I see with this kit is that is it keeps the “stock” fuel mounting location and still allows for adding the S&B disaster kit as sold. No mods or extending lines that some relocate kits do, making adding the S&B a little more difficult.

[@sakoboomer2420]

Have you had any trouble with leaks? I have had trouble with leaks and am dropping the tank for a third time to fix the leaks. Ass full of that!

[@PowerstrokeRick]

No leaks over here. Where are you getting leaks from?

[@sakoboomer2420]

@@PowerstrokeRick leaks are coming from the hoses that SPE Supplied

[@mikegonzales1564]

There is a o ring that comes with the water separator.. where does it go? I could not see yours on the video?

[@Bmitch3521]

When you take the water separator off, you should see the old o ring still on the mounting bracket. If not, it goes on right over where you screw the separator on and push it on as far as it can go.

[@PowerstrokeRick]

There is already a O-ring on the inside threads of the filter so this one it comes with is a extra application

[@mikeventi637]

Rick...what did you do for your upper fuel filter?

[@PowerstrokeRick]

SPE Kit converts the upper to be mounted down below with the water separator

[@MoreLikeJesus93]

Great video! Wheel setup?

[@PowerstrokeRick]

Thank you! In this video they are 22x12 and 33x12.5 they are different now

[@stephenrobertson2397]

You are awsome.

[@PowerstrokeRick]

Thank you 🙌🏼

[@jonahcruz6233]

Hey , I did this kit , on a 2018 ford 2018 XLT , cat oil filter, went to reset my oil light and I notice , that I don’t have any percentages reading , just a blank screen, had that happens to you ?

[@PowerstrokeRick]

I have not had this happen I will look more into this!

[@AustinRiley-k1x]

After I installed this system on my 2017 platinum I experienced a pretty loud winning noise like my fuel pump or cp4 and it turns over more now to start. These issues were only experienced after this system was installed. Did or do you experience this ? Just want to know if this is normal ?

[@PowerstrokeRick]

No I didn’t expierence that. You get any low fuel pressure codes? I had a wine after first start up other then that once the air was out I was good. My 2015 has a wine on the fuel bowl that’s a bit loud but common thing on those trucks

[@AustinRiley-k1x]

@@PowerstrokeRick it wines typically when im driving sometimes at idle but not all the time. And no codes at all pop up.

[@Sasquatch7.62]

I got a 14 and want to do that on mine. Do they have that kit?

[@PowerstrokeRick]

Not yet! They offer the Manifold block for the engine bay but not the filters yet

[@jaredcooper1355]

I would buy some stickers!

[@stephenrobertson2397]

Where is best place to purchase the kit?

[@PowerstrokeRick]

Get this at www.SPEMOTORSPORT.COM

[@dillonallen9626]

I’ve got one for sale 1/2 price , used about 2500 miles.