10 minutes How to change Water Pump 2010 ETEC 60HP Evinrude

[@perrinayebarra]

Nice of them to use every possible size bolt.

[@chadjansen9097]

Good video Sir. Straight to the point. I've got mine done. Took a little longer than the video though. :) thx again. Happy boating

[@davidmeyer5483]

Nice video always learning. Not looking forward to pulling my unit apart but the water pump probably needs changing and I’m going to try it myself without taking it into a marine dealership to do it.

[@JBHIFI-fo4lb]

How did you go? Was it easy and did it last?

[@moparmadman1134]

Great video .Is the 90 HP much the same will be doing pump tomorrow.

[@ayhankucukozer1478]

My dear friend, the exhaust muffler of the 30 hp evinrude eteceh engine was shattered in the middle. Will it cause any harm? Will the engine start

[@extracoolmurphy]

hey quick question I have a 1993 30 hp ELS and today did the water pump removal and install all seemed fine but starter wont crank motor? bat has juice, starter spins flywheel fast with plugs out. prop and flywheel will turn manually in drive but it is not easy. I can shift from F-N-to reverse, do you think the driveshaft be misaligned? It would break your arm trying to pull a rope manually in neutral. I should have tried to start it before doing the repair.

[@Rowintelplus]

try dropping the lower unit and then starting the motor without the "foot" on it. That will at least narrow it down to a powerhead or gearcase problem

[@tomcox5063]

Thanks for an excellent tutorial

[@geetarnut]

WOW! I SURE DON'T MISS THE COLD WEATHER UP NORTH IN NEW YORK! BEEN IN WONDERFUL "WILMINGTON, NORTH CAROLINA" FOR ALMOST 14 YEARS NOW, AND OUR WINTERS ARE GREAT! WINTER TEMPS AVERAGE AROUND 40 TO 50 OR SO! AND IT'S NOT QUITE AS HOT IN SUMMER AS IT IS IN FLORIDA EITHER! IT'S A WONDERFUL CITY!!! A BOATING MECCA TOO, BEING IT'S CALLED "THE PORT CITY"! AND I'M A 28 YEAR OUTBOARD TECHNICIAN! I SELL THE HECK OUT OF 2 STROKE OUTBOARDS,, MOSTLY JOHNSON & EVINRUDES!!!

[@79Satd]

I always measure the length of the linkage rod as soon as I drop the lower just in case it gets turned in the process. Just a recommendation.

[@pacman255]

you made it look so easy, did you have to use any gasket glue? Thx

[@Rowintelplus]

Pacman Au Doesn't hurt to use it, but if you are replacing all the parts including the housing and base plate, then you shouldn't need any.

[@pjtaylor3]

how old is that engine. it looks like it's done some miles

[@tomjohansen2083]

what about that sound that you talked about in the beginning of the video? I have the same sound when turning my propeller on my 75hp etec 2005. someone who knows?

[@nobody46820]

Good vid. Would have been nice to know the year, make, model and hours on the engine b4 you started.

[@LUckybones25]

Thanks for the video! I found it very useful.

[@soktheaseng6974]

Thanks alot for sharing your video I learn alot!!

[@diegomejia2874]

Hola .te saludo desde Colombia saludos.

[@davidmann1718]

Awesome video. Thank you

[@fiishermanroly]

Thx for the video

[@colbydoyon8547]

I know this was last year but you really need to clean that thing

[@mrmuskey5202]

ya no shit

[@Dogbang1827]

yo what happened to your boat engine it's dirty you need to wash it I'm not mad I just saw that it's dirty

[@Salty_reviews]

Your voice reminds me of Kermit the frog!

[@Rowintelplus]

+mgrande11 Ah yes, my favorite childhood character!

[@Salty_reviews]

ROWINTEL.COM me too!

[@bradcreber75]

Who cares about how someone's voice sounds like? What does that have to do with the video? I'd rather spend the extra money and have my mechanic do this. Pain in the butt. LoL. Certainly is a mess of a engine shaft and I can't believe he wouldn't take care of basic cleaning to make it look good. He takes all that time just to replace the impeller but can't take any time to keep it nice and clean. What a mess!!

[@andrewfinlayson1507]

Trim Tab?????????????

[@sketchbreaker]

dude your boat is filthy cover that up

[@olegnovfishing3391]

жесть!

[@mrmuskey5202]

Clean it up well before you start, just to show some respect. Also, tightening the aluminum unit into a vase without some type of protection tells me your not a tradesman.