@@Crystalservices it seems people liked it. It was a real storm.
@ajaks763611 ай бұрын
Very Interesting, and Educational!! 2 Great Repairs, 1 Video. Thank You.
@ToltecMerc11 ай бұрын
Glad you enjoyed it!
@rfr65311 ай бұрын
Good job mate 👍
@ToltecMerc11 ай бұрын
Thanks for the visit!
@Foxx_6911 ай бұрын
I really enjoy watching your method of troubleshooting. The thunder was nice ambiance!
@ToltecMerc11 ай бұрын
Glad you enjoyed it! I totally planned that background thunder.
@vadilsonfula9434Ай бұрын
Hello, good afternoon, I really liked the video, good work, this is Vadilson Fula from Angola.
@Gamehunter407011 ай бұрын
Good job
@ToltecMerc11 ай бұрын
Thanks!
@keithsmith703111 ай бұрын
Great repair as usual, you the King on these repairs 🙂. Looking forward the the next 1
@ToltecMerc11 ай бұрын
Thanks! Lots more to come!
@amjadalheeh27982 ай бұрын
many thanks for this video ... I'm also working in ps5/4 field ... you save my life carer
@kikihobbyrepair11 ай бұрын
I love your videos. They are so educational.
@ToltecMerc11 ай бұрын
I'm glad you find them valuable. I have enjoyed making them.
@muratrisvan11 ай бұрын
Thanx master ❤️🇹🇷
@ToltecMerc11 ай бұрын
You're very welcome!
@jengen362411 ай бұрын
nice repair as always
@ToltecMerc11 ай бұрын
Thank you so much!
@haakmeer11 ай бұрын
great repair again
@ToltecMerc11 ай бұрын
Thank you very much!
@Console_Tech11 ай бұрын
Nice work
@ToltecMerc11 ай бұрын
Thanks for the visit! Come back any time!
@slickrx690811 ай бұрын
Yay! Was able to repair one PSU by replacing a bad 18N60M2. Was thrown off by the 1.5V diode reading bc my Fluke reads Pin 8 at 0.816V on a known good.
@MicroMageRepair11 ай бұрын
Might eventually watch enough of these to get the guts to try one 🤣
@ToltecMerc11 ай бұрын
Go for it! You're a wizard after all!
@arthurgomez194111 ай бұрын
Master tech toltecmerc! You make it look easy but its not lol awesome jobs
@ToltecMerc11 ай бұрын
Thanks 👍
@Todestelzer10 ай бұрын
11:25 to be sure the driver is good can’t you power up the PSU without the MOSFETs and check the gate signals with a oscilloscope?
@ToltecMerc10 ай бұрын
No, I don't believe so. This supplies shutdown very quickly when they detect any kind of problem. I don't believe it will send out gate pulses endlessly without seeing voltage from the feedback circuit.
@vadilsonfula9434Ай бұрын
I would like to know the value of the resistor and the power, please, thank you.
@Discretesignals11 ай бұрын
Are you on the East Coast? Here in central FL it's been rainy, sticky, gloomy, and cool for over a week now.
@ToltecMerc11 ай бұрын
A little further west.
@richieb967529 күн бұрын
Hello, is it possible to get rid of the coilwhine under load by putting silicone around the capitators?
@Moby413 ай бұрын
Hi @ToltecMerc I have the same power supply that was blown up by a cockroach around the 40N60M2 mosfet and it took some fusible resistors and the ZM diode with it. I replaced the resistors at R7, R88 and the mosfet (still waiting for the ZM diodes to be delivered), and the DAP chip. I have 3 shorted capacitors at C85, C31, and C75. I recently asked you on JoeyDoesTech's stream if they were meant to be shorted and you told me C85 is meant to be 2.72ohms, C31 0.07ohms. I didn't know C75 was shorted at the time so I didn't ask you about it. Anyway. I tested all 3 of these caps out of circuit and they aren't shorted, however their respective solder pads short to eachother. Do you have any idea what it could be? I've probed around so much and just cannot seem to find the cause (keep in mind I am a beginner). I tested the mosfet at Q34 and I think it was reading around 360-430ohms. Somewhere in that range. Any bit of advice would be greatly appreciated. Thank you. EDIT: Welp. It's not actually shorted. The problem was just me not knowing how to properly operate/read a multimeter 😅 Thank you for your help!
@R2OBD10 ай бұрын
HI, Could you help me identify a couple of components on the FR board please? one is a vener marked VM V1 (ZD39) and another is a diode marked GS5MB (D1) if you have mnuafactures codes that would be so helpful. I have had two supplies blow the R100 resistor (R96) as well as one of these diodes which i havent seen you come across yet
@ToltecMerc10 ай бұрын
ZD39 should be marked ZM. It is a PDZ18B from NXP. GS5MB looks to be a general purpose 1000V, 5A diode. www.jjwdz.com/pdf/zhengliu/GS5AB~GS5MB%E4%BA%A7%E5%93%81%E8%A7%84%E6%A0%BC%E4%B9%A6.pdf
@hsp13168 ай бұрын
13:25 you mentioned 0.1ohm, is it the same one that ps4 has 0.16ohm 1 watt?
@Crystalservices11 ай бұрын
Why are you not using desolder pump
@ToltecMerc11 ай бұрын
It's not plugged in. By the time I get it plugged in and it gets up to temperature I can already finish the job with solder wick.
@Crystalservices11 ай бұрын
@@ToltecMercohh it's great 👍, I am talking about non electric manual one.
@banjomaniac11 ай бұрын
Do you repair ps5 from viewers? I have one with a 400FR supply that was dead i replaced the power supply now it just beeps? I'll keep watching you are the best!
@HADE-rg6jx11 ай бұрын
Hello. I have a burnt ic whose name I don't know. in ps5 edm-010 can you help me😢
@ToltecMerc11 ай бұрын
If you email me a picture of the IC and the area around it, I might be able to identify. toltecmerc@gmail.com
@HADE-rg6jx11 ай бұрын
Thank you 🌹. I sent the picture to your email.
@ngonohtc57247 ай бұрын
Please what is the part number of q34 mosfet
@Moby413 ай бұрын
I know this is 4 months late but it is 2N7002K Hopefully you've got your power supply all fixed by now though
@ngonohtc57243 ай бұрын
@@Moby41 Not yet, I didn't know how to identify the part number of q34. Thanks for the reply I will order 2N7002k and try to fix my PSU
@Moby413 ай бұрын
@@ngonohtc5724 Awesome. Best of luck and stay safe!
@mikeanderson199411 ай бұрын
The swallowing sounds couldn't continue to watch i love every video repairs including your's but i can't continue I'm sorry 😂😂
@ToltecMerc11 ай бұрын
Sorry. My sinuses are suffering right now.
@mikeanderson199411 ай бұрын
@@ToltecMerc oh man i didn't mean to I'm really sorry hope you get better soon again I'm really sorry didn't mean it 🌹🌹