16v Samurai: Aluminum Radiator and Header Install!

[@Smithyboi473]

Love the build and the sound of that exhaust. Could you do a listing of what modifications and parts that was used for this swap please.

[@alexandrlavrenko3193]

I like the sound the engine makes, what muffler do you have?

[@alichaudhry1]

Very nice would love to see more videos on your samurai

[@dylanrav]

love the build! where did you get all of those blue silicon pipes?

[@tombulli1236]

HI ! cooler Sound !! Hi ... cool sound! My Suzuki Jimny FJ has almost similar sound ... I have sports exhaust from Fox, sports filter K&N and snorkel (it draws a lot of air in ...) My next project will be a 1.3 GTi Shift Motor ... Greetings from Germany .. Subscribed :)

[@zms7548]

Great job but did you test on Dyno we need to know the output power

[@Como651]

I just bought a Champion radiator for my 1988 Samurai that looks nearly the same as yours but the hood hits it. I noticed your new radiator looks slightly taller. Did you have any issues with it not clearing the hood? Did you have to make any mods to clear the hood?

[@wesleybarton2880]

absolutely awesome videos!!!!

[@ncriddle]

God what a beaut... I want one so bad.. Been lookin for months

[@chrisboucher2813]

What exhaust are you running on that thing? It sounds wicked! I need to replace my headers it's cracked really bad, I got a Sammy similar to yours

[@DangerDave95]

Long tube header to 2.5 pipe and a single chamber muffler.

[@dunstanlataille4937]

We're did you get the blue wire from send the link for dem

[@claytonmenezes5980]

Danger Dave please provide us the link where you bought it from . Thanks

[@noahdunaway]

What oil filter is that I see on the engine ? I have a 1996 Tracker 1.6L 16 valve and researched the oil filter crossover and found that the K&N HP-3001 fits and gives you about a half quart more oil capacity.

[@DangerDave95]

I use motorcraft FL-400S. Good cheap filters. Has the anti drain back valve.

[@noahdunaway]

@@DangerDave95 if you want a little more oil capacity you can use a FL-1A Motocraft , that is what crosses over to a K&N HP 3001. They both have anti drain back valves but since the filter is mounted on a downward angle you really don’t need it. With the bigger filter I’m able to put a full 5 quarts of oil in it. It calls for 4.4 quarts and on my dipstick with the bigger filter 5 quarts is just over the full mark. On all my vehicles I like to use as much oil as safe to do because the oil is part of the cooling system so I usually fill the crankcase to about 1/8” above the full mark. Most engines can be over filled a quart of oil and you only get in trouble if you put two or three quarts over the recommended amount.

[@kbpsn1976]

Hi where did you get the headers from

[@AnhPham-md6mm]

Interesting

[@dunstanlataille4937]

Send the link for the headers

[@oczuk32]

On the stock header, what down pipe were you using? I'm having clearance issues with my stock header.

[@DangerDave95]

The one that came off the geo tracker

[@jayrajkhanna3896]

How much torque and power does this motor make ?

[@WillCB7]

Hey, would you be able to share the link for the headers ? Please.

[@kellyanderson7115]

You're better off with the tri-y header, they're the best way to extract as much torque/hp on small displacement motors.

[@DangerDave95]

I wanted to get a shorty header that was a tri-y but they were sold out indefinitely... The old manifold was full of cracks and the flange bolts were completely rusted and I couldn't get them off.

[@ywiwar7872]

3 Jesus handles - nice

[@DangerDave95]

The wife likes to use them all when I drive lol

[@maximo979]

What temperature does it ride at now with the new radiator? Nice samurai by the way

[@DangerDave95]

Around 185 195

[@russgould707]

That's about where mine runs at with the same setup you have.

[@iratiagirrezabala4037]

Oso ona, segi horrela!

[@dannyws696]

Link for the headers and radiator plzzz!!

[@ΜΑΜΩΝΑΣ666]

HELLO FROM GREECE!COULD YOU GIVE ME A LINK FOR THE HEADERS.I HAVE A VITARA 1.6 16V AND LOOKING FOR HEADERS.

[@TheJonathandrumer]

HELLO, HOW ARE YOU, YOUNG MAN, YOUR ZUZUKI IS VERY NICE, I HAVE ONE AND WE ARE MOUNTING THAT SAME ENGINE, I WOULD APPRECIATE IF YOU COULD TELL ME WHERE YOU BUY THE RADIATOR FAN, THANK YOU VERY MUCH IN ADVANCE

[@rubenmarquez8777]

It’s a bit pricey but look up Suzuki samurai flex-a-lite fan. Fits perfectly

[@EVERYTHINGGUY226]

I just subscribe buddy

[@xmoose7796]

What engine you use it

[@DangerDave95]

96 geo tracker 1.6l 16v

[@restoreman8115]

@@DangerDave95 hi, what about wiring?

[@DangerDave95]

@@restoreman8115 96 1.6l wiring harness is spliced into the factory wiring in the samurai.

[@restoreman8115]

@@DangerDave95 great, any source for a how to manual ?