Tap to unmute

181. M/S. 33 Installing a key switch and selenoid on my Snapper tractor

  Рет қаралды 11,326

Jim Jackson (Jim's Fix-It Shop)

Jim Jackson (Jim's Fix-It Shop)

Күн бұрын

Пікірлер: 55
@jimoakley4944
@jimoakley4944 Жыл бұрын
Great Video Jim One thing- I have a Snapper 550z with the Kawasaki engine. Looking at the wiring diagram for that mower, the L on the ignition switch is for the Electric Clutch and the fuel solenoid. Hard to find much info on my old tractor but I did find the wiring diagram. It does not have lights but I intend to put lights on it. Once again, great information and thanks
@jimjackson9381
@jimjackson9381 Жыл бұрын
Well, in your case, I would hook a wire to the hot side of the starting solenoid, run it up somewheres to a toggle switch, and then to the headlights, unless you have a dual stater on your engine that puts out AC/DC use the AC side of the stater to run your headlights, and of course, the DC side to charge your battery. Jim.
@amathonn
@amathonn 2 жыл бұрын
I went out and bought one of these load testers as soon as I saw your video. 19.99 at Harbor freight. Very happy with it
@Morningsunwoman
@Morningsunwoman 5 ай бұрын
Well Jim I really could have used installation on the mower…my solenoid was just hanging out under the seat with no bolts holding it down
@kevinwebb6060
@kevinwebb6060 4 жыл бұрын
great video Jim - thanks. I am replacing my old snapper mower 8 hp B&S engine and want to replace my old push button start / kill switch key set up with a ignition switch and solenoid like in this video. I plan to get the exact parts you used hopefully. I'm not sure how to connect the charging line back to to battery though - hopefully my new engine will come with instruction on how to do that (most look like they have a connecting female plug with 2 wires in it). I'll email you if I have issues. Thanks for all you do!!
@jimjackson9381
@jimjackson9381 4 жыл бұрын
Kevin Webb I doubt the engine will come with any instructions if you need help wiring that up let me know usually has a plug with two wires typically one wire comes from the stater and one wire goes to the coil some of the newer ones will have one wire from the stater and one wire going to the solenoid on the bottom of the carburetor, just trace the wires back and see where they go otherwise let me know and I’ll help you through it. Jim
@charleshoward35
@charleshoward35 6 жыл бұрын
Thanks Jim, always enjoy your videos. from South East, Texas.
@mikegorton691
@mikegorton691 Жыл бұрын
Jim- where is my solenoid located on my craftsman/snapper 28 inch 12.5 hp mower model 107.280340. is it behind or underneath the seat? thanks pic or whatever? my manual only shows the schematic and not location of it-
@genesnider4586
@genesnider4586 8 ай бұрын
Where does the magneto wire connect in the system?
@jimjackson9381
@jimjackson9381 8 ай бұрын
The magneto wire coming from the ignition switch or from inside the engine? Jim
@genesnider4586
@genesnider4586 8 ай бұрын
@@jimjackson9381 from the engine side.
@jimjackson9381
@jimjackson9381 8 ай бұрын
@@genesnider4586 the magneto shorten wire coming from the coil should connect to the magneto shorting block on the engine by the carburetor. Jim
@djpainting7769
@djpainting7769 Жыл бұрын
My snapper starts with key but won't shut off unless you ground it out,?
@jimjackson9381
@jimjackson9381 Жыл бұрын
Well if I had to guess I would say your ignition switch is bad or the wire coming from the ignition switch going to the magneto shorting block. Jim
@stevecupit4655
@stevecupit4655 2 жыл бұрын
Where do you ground your key switch terminal to.
@jimjackson9381
@jimjackson9381 2 жыл бұрын
The ignition switch has a external ground through the switch itself once you bolt it into the machine it’s grounded automatically. Jim
@stevecupit4655
@stevecupit4655 2 жыл бұрын
Thanks Jim. Glad to see someone that really answer your video questions. Your videos have really help me redoing my snapper
@raleighstephens9293
@raleighstephens9293 2 жыл бұрын
Hello. I really have been enjoying watching your videos... very informative. My question is can I take electric start from 10hp briggs/stratton snapper rider to 11.5 hp snapper rider?
@jimjackson9381
@jimjackson9381 2 жыл бұрын
If the bolt pattern on the starter matches the engine block I don’t see why you couldn’t change them just the first time you started make sure it’s engaging in the fly wheel properly but you can compare the two when you have them off and see if they look the same. Jim
@CerebusTV
@CerebusTV 6 жыл бұрын
Always a good idea to use relays and solenoids. You can always substitute a Ford starter relay as well, which lasts a lot longer. You can solder the connectors as well as crimping.
@Garylee62
@Garylee62 3 жыл бұрын
My snapper will start up with the key but the key will not turn it off... what should I check?
@jimjackson9381
@jimjackson9381 3 жыл бұрын
The key switch sounds like it’s going out. Or it’s your wire on your magneto shorting block. Jim
@Garylee62
@Garylee62 3 жыл бұрын
@@jimjackson9381 Thanks Jim! I’m going to recheck all of that tomorrow. I love your videos! I’ve learned so much about Snapper mowers from watching your videos! 👍🏼👍🏼
@stuestrade7494
@stuestrade7494 2 жыл бұрын
Stu Estrade 0 seconds ago I have a Snapper RER Mower 7800920-00 with a 17 hp B&S Intek engine 31C707 603 E1 What non-Snapper product is available for an ignition coil, solenoid, starter, and spark plug is applicable to my mower and engine? Snapper parts are pricey! Thanks
@jimjackson9381
@jimjackson9381 2 жыл бұрын
A lot of that stuff you can find at your local True Value Hardware. store where I buy mine or Lowe’s or Home Depot or Menards. Jim
@boatbuilder1954
@boatbuilder1954 9 ай бұрын
The one on the bottom? what letter is that, what does N stand? for you mention kill wire twice ? does one come from the engine and the other go to ground? you lost me ?
@jimjackson9381
@jimjackson9381 9 ай бұрын
The N. On the back of the ignition switch goes to the kill wire on the magneto shorting block on the side of your engine. If you send me an email, I can send you a schematic that I made that labels all of them. Send it to Jimsfixitshop@gmail.com. Thanks. Jim
@babyrandle596
@babyrandle596 3 жыл бұрын
I have snapper riding mower it runs but, it stop from the switch
@jimjackson9381
@jimjackson9381 3 жыл бұрын
I’m not totally sure I understand what your issue is you said your machine stops from the switch which switch is giving you problems. Jim
@donfrentzel2739
@donfrentzel2739 6 жыл бұрын
Another good video. I'll save it, I'm still pull starting mine but in the future you never know. St Louis
@johncarter-sn4pj
@johncarter-sn4pj Ай бұрын
Motor wont shut off
@jimjackson9381
@jimjackson9381 Ай бұрын
@@johncarter-sn4pj if a motor won’t shut off, you have a broken wire somewhere between your ignition switch and the coil itself If you have electric start, this will be easier pull the recoil cover off the top of your engine. Started it take a wire and go from ground to the small little tab on the side of the coil that should kill the engine if it doesn’t then you could have a coil, but I really doubt it. Jim
@timothymowery4559
@timothymowery4559 3 жыл бұрын
Jim, think I've seen every vidio you have, Thank You. But I've got a problem no one can figure out. Snapper 285Z, start engine, go to release the brake lever the engine dies. Checked the seat switch, got it crossed over. Checked all 3 Stens safety switches (2 levers and brake) changed out PTO Switch and raise and lower Switch. Still same problem. What you think? Thanks Tim
@jimjackson9381
@jimjackson9381 3 жыл бұрын
I’m not familiar with that model number but is there a switch on the clutch pedal there is on the rear engine snappers and that typically gives people a lot of issues. Jim
@20x20Ghost
@20x20Ghost 3 жыл бұрын
Jim my Ignition switch has an M on it where does that run to please?
@jimjackson9381
@jimjackson9381 3 жыл бұрын
You need to send me a picture of the back of the switch The switches are yours don’t have a M they have a N . Jim
@williamdavis9943
@williamdavis9943 4 жыл бұрын
I just replaced my 12.5 H.P. engine in my 2003 Snapper with a 2018 11.5 Briggs & Stratton engine . This has a voltage regulator & a solenoid operated carbuerator. I hooked the kill wire from the coil on the new engine to the black wire of the ignition switch ( marked M) but the coil will only fire if I remove the kill wire from the coil the coil will operate. Do I need to replace the ignition switch? The ignition switch on the machine now has B, G, M, S, that's all. B is red, S is blue, G is green & M is black. I have no idea how to hook up the carb.? Can you help?
@jimjackson9381
@jimjackson9381 4 жыл бұрын
William Davis I’d like you to watch video number 301 explains how to wire the engine that you’re putting on if you have any issues that’s not covered by this video please let me know.Jim
@richardrodriguez7360
@richardrodriguez7360 4 жыл бұрын
I'm about to install a key switch and the solenoids on my snapper riding mower Do you have any diagrams to installing
@jimjackson9381
@jimjackson9381 4 жыл бұрын
Richard Rodriguez You need to watch video number 181 that should help you out let me know. Jim
@kenneybert7597
@kenneybert7597 5 жыл бұрын
i have a YT112 ingersoll which is a case tractor ... i cannot wire that ignition to save me ... its the normal 5 post ignition like most all others ...when i got it the wires were off and the ignition was shot so i took another ignition out of another old mower ,, ive been playing with that thing all day plugging wires here and there ,, i can get it to turn the motor but not start ,, im not sure what to do next ,,,,
@jimjackson9381
@jimjackson9381 5 жыл бұрын
Kenney Bert Hi it’s Jim Do you have any paperwork on the machine as far is a wire harness. Can you send me pictures YT112. Doesn’t sound like a Ingersoll number mine is eight 3016 and there’s 4016 models the 3000 series has the small back tires the 4000 series has the large back tires which does yours have, some pictures would be awesome the entire machine under the hood the dashboard things of this nature. Jim Send pictures to. jimsfixitshop@gmail.com
@babyrandle596
@babyrandle596 3 жыл бұрын
My snapper runs, but cut off by the switch
@michaelanderson8714
@michaelanderson8714 6 жыл бұрын
I have electric start but it's not working. I was told to test the solenoid by jumping across the two post and if it started, the solenoid was bad. It did start so I replaced the solenoid. The mower started after the repair and the next time I used the mower. When I tried to start it two weeks later it wouldn't start. The starter just kept clicking. I had to pull start the mower. With a new solenoid and battery, is it possible the key switch is bad? The run position works just not the start. For shits and grins I just tried to jumper the two post on the solenoid again and it wouldn't start. Is that a sign of a bad starter?
@exinanition2307
@exinanition2307 6 жыл бұрын
Michael Anderson, if your engine has overhead valves you may just need to have them adjusted. Over time the valve lash gap can get too large which will cause your engine to have too much compression because the valves open too late and close too soon as well as not opening enough. This effectively causes too much compression which places an undue load on the battery and the starter. This effect mimics a weak battery and/or a bad starter. I have seen many people go buy a battery, which did not correct the problem, so they went out and bought a starter, which also did not fix the problem. Then they go and buy a solenoid, which will also not fix the problem, so they take the engine to their local shop only to find out a quick and simple valve lash adjustment would have gotten them up and running. The bad news is they are now out a load of cash unnecessarily. If you have overhead valves it is worth the time and minor expense to have them correctly adjusted. This is, in fact, a regular part of good maintenance. Then if you still have the problem with starting your mower you can address that issue. It would be a great idea also to check for loose or corroded connections on your wiring. You may just save yourself a ton of money, which, if you are like me, you could gladly spend on something more important to you.
@michaelanderson8714
@michaelanderson8714 6 жыл бұрын
It's a Briggs & Stratton Vanguard 16HP OHV V-Twin engine. The odd thing about it is that I had no starting issues until I power washed it. I had to pull start it after that and it starts on the first or second pull each time which surprised me considering it takes at least 5 pulls on my 7HP push mower. I'll keep the valve lash in mind but for now the pull start will have to do.
@exinanition2307
@exinanition2307 6 жыл бұрын
Then you may want to look at your electrical connections. It is possible the pressure washer may have caused something to come unplugged preventing your battery from being charged. Is your battery discharged? I ask because you said when you tried jumping across the solenoid the second time it just clicked and that is what happens when the battery is discharged.
@touchsok99
@touchsok99 5 жыл бұрын
Jim my snapper start but I shut off it won't started again help?
@jimjackson9381
@jimjackson9381 5 жыл бұрын
Sok Touch Hi it’s Jim I need a little bit more information than this, does the starter turnover, does it have spark to the spark plug, if it does have you changed the spark plug, does it have a fuel filter on it that could be plugged, try changing that if it has one. Let me know what you find out.Jim
@touchsok99
@touchsok99 5 жыл бұрын
Jim Jackson okay I will check the spark and I will let you know thanks Jim
@touchsok99
@touchsok99 5 жыл бұрын
@@jimjackson9381 I let's you know
@paulTaylor-ri1kf
@paulTaylor-ri1kf 5 жыл бұрын
I know this video is 1 year old but do you still the wiring diagram and the parts list. Thank you..
@jimjackson9381
@jimjackson9381 5 жыл бұрын
paul Taylor Hey Paul it’s Jim I drew up a wiring diagram and emailed it to you let me know if you get it. Jim
@floorman1954
@floorman1954 5 жыл бұрын
Can I get Jim’s email?
How to test a tractor solenoid
7:48
doublewide6 Repairs LLC
Рет қаралды 661 М.
How to treat Acne💉
00:31
ISSEI / いっせい
Рет қаралды 108 МЛН
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 31 МЛН
So Cute 🥰 who is better?
00:15
dednahype
Рет қаралды 19 МЛН
214. Installing a headlight on my 2012 Snapper
27:44
Jim Jackson (Jim's Fix-It Shop)
Рет қаралды 3,6 М.
Simplicity 700 725 B1 Garden Mark Wiring made simple!!
8:07
Zippo Varga Small Engine Medic
Рет қаралды 79 М.
291. M/S 57.  How can I adjust my belt and my clutch on my Snapper RER.
10:31
Jim Jackson (Jim's Fix-It Shop)
Рет қаралды 21 М.
How to replace a 4 terminal solenoid
5:02
Old School Mechanic
Рет қаралды 45 М.
How to (voltage drop) test a starter motor circuit
11:06
Justin Miller
Рет қаралды 517 М.
How To Replace The Solenoid On A Snapper Rear Engine Rider
4:19
Online Small Engine Mechanics
Рет қаралды 14 М.
How to treat Acne💉
00:31
ISSEI / いっせい
Рет қаралды 108 МЛН