Nothing beats a couple friends wrenching in a shop. TY guys and please keep the vidyas comin as long as you can. Again, TY very much enjoyed the content.
@jennyanimal90463 жыл бұрын
I'm glad to see young bucks like you keeping it alive. You guys rock..god bless you
@jasontaylor9702 Жыл бұрын
Proud of you young guys. I just bought me a '63 two door hardtop! My favorite
@johnelliott73753 жыл бұрын
You went that far and trying to get the most good for the buck , I am shocked you didn't look in the bottom and just take the word of someone, plus as you said who knows what is in there or if it was installed correctly. Good luck with your work and I will hope you the best of luck with your new motor.
@sgtyork93303 жыл бұрын
I had a 64 Impala hardtop when I was 18. Had it a few years but sold it. Wish I still had it. 327 350hp and 4 speed. Originally had a 283 2 barrel.
@philhunt39083 жыл бұрын
One tip on the strocker engine keep a short dip stick in it when you drive and use the long just to check the oil a friend of mine found that out the hard way the long one got cought up and he lost a Piston
@garywilson123 жыл бұрын
glad to see you young guys having such an interest in the old cars, keep videos coming
@harneyracing3 жыл бұрын
You guys need to pull that engine. Look close the pistons are upside down
@timothyballinger62803 жыл бұрын
Cool I was two for two. You guys have done everything exactly as I would have. So far I'm really impressed. On to part three. 👍
@martydegier92793 жыл бұрын
Dude,that things mint..&a treasure trove of parts as well.Fantastic find!
@marktucker58373 жыл бұрын
283 327 best chevy engine ever made they run for ever
@CountryBoyGasGarage3 жыл бұрын
I bet it will run fine! I can't wait to see it fire up! 👍
@brandonbell81593 жыл бұрын
Yeh with the upside pistons though 🤣🤣🤣
@Scrapy-ih7ob3 жыл бұрын
wow, looks like you dodged a bullet... You defiantly dropped that oil pan take a look in there,, that's allot mouse activity, for there not being any mess down there.
@robertschmidt63833 жыл бұрын
The top of the engine that's crusty sure makes me want to run it through a blast unit to clean it up.
@thomasvorwerk92963 жыл бұрын
My Dad purchased a 1963 Chevy Impala 2-door hardtop for me when I was in High School back in the middle 1960's I could get it up to 119 on the interstate. Wish I still had it today.
@thecollectoronthecorner70613 жыл бұрын
Pull the oil pan. and clean it really good. You gotta loosen it to properly install the Timing Chain cover anyhow.
@brandonbell81593 жыл бұрын
And pull the engine and have the pistons put on the right way lol. There upside down
@delhudnall99863 жыл бұрын
love them 63s make it work and thanx
@patmurphy52373 жыл бұрын
I can’t wait to see if it runs. 👍
@jennyanimal90463 жыл бұрын
Looks super clean
@jennyanimal90463 жыл бұрын
You guys are making Americans proud..
@rickallen63783 жыл бұрын
You mean they're proud boys?
@rickallen63783 жыл бұрын
I would just pull off everything possible and clean it out. I never saw you turn the motor by hand on this video, guess I missed it. I see you guys are from Elk Mound. I grew up in the Spring Valley, Plum City area. Moved away in 1977. Lucky to find any descent old cars from that area with all the salt on the roads.
@bobbysanders77253 жыл бұрын
The only change I would make would be a three duce set up. 63 Impala is my favorite of them all and I had a 1969 Impala factory 427 automatic.
@andymacdonald15353 жыл бұрын
That's what's called a mouse motor converted to a rat piss motor. I'll bet it has to come out and be totally disassembled. Rat piss has probably got in the oil pump and locked it up too. Looks like they pissed down the distributor pretty regular.
@timwhite88783 жыл бұрын
Love these old Chevy.
@williamsouthard52203 жыл бұрын
Give it to me when you are done I love that car I had one but it was a 1964 Impala
@79tazman3 жыл бұрын
That engine needs to be cleaned real good all that crap in there has gotta go If that was mine I would tear it right down send the block to hot tank it and get it cleaned before even thinking of running it
@davidsantos82063 жыл бұрын
Great video guys, I just wish you would have made it a little longer. And a 327 bored 60 over, should make for a really nice little screamer. Thanks for entertaining us. Looking forward to the next video
@resurrectionauto57143 жыл бұрын
Thanks for the support! This “build” series is shot day by day so some will be longer than others. Unfortunately today we didn’t get to work on it. Check out our other videos for more variety
@bamadigger43423 жыл бұрын
Gonna be clean as a whistle
@rickbandy38623 жыл бұрын
Drop the pan! And just clean everything good, especially after "chipping that distributor shaft out. If metal or mouse turds get sucked into the oil pump it will get to the bearings and you withh have a boat anchor of an engine.
@jamesveltman55553 жыл бұрын
It does. Ot matter about the motor. Rebuild it, sell it and use the proceeds for an Ls 3
@donnahutchinson4963 жыл бұрын
Will need total teardown
@robertsweet41123 жыл бұрын
If anyone can make it work...its you two
@darrellroeters49513 жыл бұрын
Yes can fix engine easily where’s the vacuum
@GeeenJ3 жыл бұрын
i'd take the sump off afterr the rats been in there betting its nasty with rat pee in the sump wont be good for the oil pump or bearings
@resurrectionauto57143 жыл бұрын
I flushed everything with a few gal of oil including running the oil pump with a drill to flush out bearings etc, was nasty the first flush
@thecollectoronthecorner70613 жыл бұрын
@@resurrectionauto5714 No way you got it clean enough. Your going to clog up the screen on the oil pump intake and starve the bearings.
@ervinthompson65983 жыл бұрын
From the looks of the valley, you’re going to put a lot of faith in not changing the cam bearings !!
@davidhimeback90873 жыл бұрын
With all that rust you need to flush that oil pump is mostly junk!!
@timothyballinger62803 жыл бұрын
Ok so I'm paused again. I was right it looks awesome so I'm guessing the other side looks as good but wasn't the header off the other side? Anyway maybe them head are better than I thought so I would use them. Ok unpause lol
@daveharris77343 жыл бұрын
I've seen mice do that before way down here in south texas.
@bigsexymuthashutyomouth25463 жыл бұрын
Surpringly clean inside there! Did y'all know that it had been built or was it a pleasant surprise for you as well?
@resurrectionauto57143 жыл бұрын
The guy said it was all redone but never fired. Unfortunately it sat for a while
@djrand623 жыл бұрын
I saw the thumbnail of those iconic body lines and had to watch. Older sister had a 63 with the 230 and a 3 on the tree. I had a 64 SS that was factory ordered with the straight six as well (grandpa was frugal and liked the trim but wanted the better mileage). So, my first car was a 6 banger that ended up with over 200,000 miles on it. You couldn't kill those straight 6's.
@resurrectionauto57143 жыл бұрын
Heck yeah! Love these old things. Check out our other videos of you like these kind of older rides
@merc-ni7hy3 жыл бұрын
ugh,,you shudda pulled the motor and took the oil pan off....and hada peek inside
@resurrectionauto57143 жыл бұрын
I stuck my bore scope in the drain plug and took a peek, she looks alright
@brandonbell81593 жыл бұрын
I think it needs more than a peek in the pan🤣🤣. The pistons are upside down!! Valve reliefs always go up on pistons.
@joehall45693 жыл бұрын
Bet ya that orangeish 54 chevy that side is good.
@davidhimeback90873 жыл бұрын
Lots of W-d40. Would be best to pill the block out....
@timothyballinger62803 жыл бұрын
Ok I paused, so I'm thinking its going to be ok but if your taking the heads off then put something better on. That's what I would do. Cool cool car
@brandonbell81593 жыл бұрын
And maybe take the whole engine out and put the pistons in the right way aswell 🤣🤣🤷♂️😡
@onlyjesusisoursaviorgscast28003 жыл бұрын
It’ll run just fine after it’s cleaned up and put back together how can I reach you I’m seriously thinking about buying it
@resurrectionauto57143 жыл бұрын
715-418-0230 or 715-205-3023
@chriscornelius45493 жыл бұрын
The oil pump pick up would worry me
@garyburchett90603 жыл бұрын
At 3:39 I'm thinking this engine is full of walnut shells; which are full of tannic acid, but for your sake I hope not. Good luck. I know this is stupid. But you did change the oil?
@colewilson44902 жыл бұрын
I'm rebuilding/swapping for a 63 Impala got a few questions. It's a 283
@mowmanjones33533 жыл бұрын
yes
@davidhimeback90873 жыл бұрын
Good chance it just needs to be lube up again an work it back an forth an mostly be ok.
@joehall45693 жыл бұрын
Bottom's gona be good, still tryin to figure out how they got in?
@charleshawkins5323 жыл бұрын
I think you got. A bit ain't got no no
@brandonbell81593 жыл бұрын
Lol the pistons are upside down
@jennyanimal90463 жыл бұрын
There's no way that engine was in that..its to clean
@resurrectionauto57143 жыл бұрын
Go watch Pt1 of the videos it explains it all. It’s a new engine hasnt even been ran before but mice got into it when it had been sitting
@laakona83813 жыл бұрын
does the nest under the intake mean it's a "Rat Motor"?
@kgooch693 жыл бұрын
It'll be fine...were you able to figure out who the cam manufacturer is and what size ?
@resurrectionauto57143 жыл бұрын
I did not check numbers on it but looks to be a slightly larger than stock cam probably close to a rv style camshaft. But I guess we will know for sure when we get it fired up and if it’s got a little RUMP RUMP to it or not!
@philhunt39083 жыл бұрын
Sad that the engine was left like that it did look like it was just rebuilt
@brandonbell81593 жыл бұрын
Yeh by a idiot 🤣🤣🤣🤷♂️🤷♂️. The pistons are upside down!!! Valve reliefs always go up on a engine
@Schmitty713 жыл бұрын
What was missing that they found their way into the lifter valley?
@resurrectionauto57143 жыл бұрын
Turns out the intake had the provision for the old style breather/ oil fill on the front of it that didn’t have a plug in it! I missed that in the first videos but will add it to the next! Thanks for watching!
@chriscornelius45493 жыл бұрын
I would be putting some diesel fuel in to clean it out before I tried starting it
@resurrectionauto57143 жыл бұрын
Flushed it multiple times. She’s clear now😁
@Carl09of093 жыл бұрын
Fixable
@markgilbertson49173 жыл бұрын
Valve reliefs on the outside of block? Pistons in backwards? Looks strange
@resurrectionauto57143 жыл бұрын
Good catch! Didn’t even realize the pistons being upside down. Just as well, not too worried being a small cam and dished piston. Having checked clearance, it cleared.
@tommyburke50493 жыл бұрын
especially when chevy pistons have reliefs on both sides......At least stock ones do.
@tommyburke50493 жыл бұрын
@@resurrectionauto5714 I think they went by markings,not reliefs.
@chadfifield82903 жыл бұрын
It will turn around
@chadfifield82903 жыл бұрын
It's a chevy it will run
@BrettRSutherland3 жыл бұрын
Pull the pan first !!!
@philipmetzner72433 жыл бұрын
pistons are in backwards
@resurrectionauto57143 жыл бұрын
Good eye, they are
@jennyanimal90463 жыл бұрын
Hello
@steven.h.hh.h78393 жыл бұрын
I want you guy's to watch this video and tell me if he's the same person. the video called, Road rage by Matthew Turnbull .?
@johnhoye45353 жыл бұрын
Crap in there
@jamesstuart23623 жыл бұрын
Maybe
@gabrielhenderson60903 жыл бұрын
How much did you pay for the car ?
@christopherohara37253 жыл бұрын
It looks like somebody built that motor and ever got it started
@brandonbell81593 жыл бұрын
Somone that didn’t know what they were doing built it lmao 😂. The pistons are upside down lol. Valve reliefs always go up on pistons!!
@tomcarnahan63413 жыл бұрын
I am telling you i had a 1963.. SS black and i put a 1969...350...in it and it was one fast car and I am still kicking my self in the ass for getting rid of it how much are you going to ask for that one
@resurrectionauto57143 жыл бұрын
Can call or text 715-418-0230 or 715-205-3023
@jontrudell75293 жыл бұрын
How MUCH $$$???
@dickaslet67693 жыл бұрын
Behold the power of rat pee.
@kevinkaminski4713 жыл бұрын
Bro it'll be fine it's a chev 350 not a Ferrari.
@originalladyinblack89433 жыл бұрын
You selling it ???
@resurrectionauto57143 жыл бұрын
Yes. 715-418-0230 or 715-205-3023
@dalekriescher74623 жыл бұрын
What to do with the car aaa give it to me. Nice car
@impalanut643 жыл бұрын
the best thing you could do with it is sell it to me lol
@brandonbell81593 жыл бұрын
You are definitely the one that needs it 🤣🤣. You must have didn’t notice the pistons are also upside down in the engine lol. Valve reliefs always go up on a engine
@impalanut643 жыл бұрын
@@brandonbell8159 could care less sbout engine have plenty its the body i'd like to have
@impalanut643 жыл бұрын
@@brandonbell8159 you sound like a democrat good luck with your prez
@whobroughtdude22312 жыл бұрын
@@impalanut64 Still crying about Trump losing!? Lol. You guys are pathetic.
@roybarry21382 жыл бұрын
Most likely.eh..
@margaretbellew33673 жыл бұрын
STOP...!!! STOP..!!! STOP..!!!!!!!! Your pistons are installed upside down.!!! You will find it hard to start, and possibly bend a LOT of valves.. Valve pockets in pistons should be up towards the lifter valley..
@oregonhotrod78473 жыл бұрын
Just wasted a lot of time to take a chance on a messed up engine. Pull the engine and do it right. Bottom end inspection is just plain old common sense. And it only takes another hour from where you're at anyways. Just saying
@brandonbell81593 жыл бұрын
Nah plain old common sense would notice right off the bat that the pistons are upside down in it 🤣🤣🤣. Valve reliefs always go up on a engine
@thomashollingshad68753 жыл бұрын
old video .... you better take the engine out pull the oil pan it full of junk
@teamotmpo2 Жыл бұрын
motor is junk from looks of it
@recon5320023 жыл бұрын
No
@kapekodbob3 жыл бұрын
Great content but awful music and too loud compared to voice level. Just about blew my eardrums listening with headser. In my opinion the music should be suttle.