1972 Norton Commando Combat Rebuild (11) - Fitting oil pump and backing plate

  Рет қаралды 14,942

The Mighty Garage

The Mighty Garage

Күн бұрын

Пікірлер
@01jimmyjazz
@01jimmyjazz 5 жыл бұрын
Looking good guys. Thanks for the link to Old Britts Dave. I Loved the Norton backdrop behind you both at the start :)
@tadpoles10
@tadpoles10 5 жыл бұрын
Thanks for the update guys, moving along now just fine. atb t ..
@dducdude6315
@dducdude6315 5 жыл бұрын
Thanks Gents,Fresh hot tea in the morning and I can watch this stuff all day!! Mike, if I develop a love of Nortons my wife is going to be looking to kick your arse..LOL Think I will go ride the Velo and see if the gear box fixed itself. :-)Thanks again.
@TheDavey333
@TheDavey333 5 жыл бұрын
Great vid and very informative. Pity it’s not a bit longer or are you dragging it out 😀 Corn flakes and a Norton rebuild, I’ll be drinking coffee next. Good work Dave 👍
@swooshdave
@swooshdave 5 жыл бұрын
With kids to tend to I only have so much free time. We’re doing the best we can!
@rsbharley4766
@rsbharley4766 5 жыл бұрын
Nice video, thanks for sharing.
@supercomp7078
@supercomp7078 2 жыл бұрын
I used to use petroleum jelly to prime oil pumps, it dissolves in the oil, will be flushed out after run in and stays where you put it until oil is flowing, cranks and bearing surfaces were always well oiled on assembly and the cam used a molly based run in lube that was as sticky as shit on a blanket.
@andrelevesque5570
@andrelevesque5570 Жыл бұрын
I also had an helicoil on my oil pump lower stud .I suspect a factory machining error on the 72 model .Strange it happen only on the lower stud
@Richard-r4u3o
@Richard-r4u3o Жыл бұрын
the reson to fit from the back is so as not to have a loose nut flying round in case it would come loose. it would be stopped by the case cover
@Richard-r4u3o
@Richard-r4u3o Жыл бұрын
what do you think about priming the pump with petroleum jelly as per the recommendation for the Buick V8’s?
@libertyman3072
@libertyman3072 5 жыл бұрын
✌🏿😜🛠️🔧🛠️🔧🛠️🔧🛠️🔧🛠️✌🏿😜
@martiniv8924
@martiniv8924 3 жыл бұрын
A shame that Fred and Ella retired 😢
@sf940477
@sf940477 5 жыл бұрын
Hurry up with the next one 🤣
@swooshdave
@swooshdave 5 жыл бұрын
Stephen Forrest They are going to come soon enough. After it gets running what are you going to have to look forward to? 😜
@soldtobediers
@soldtobediers 5 жыл бұрын
''You can spend the entire second half of your life recovering from the mistakes of the first half.''-Saul Bellow Funny;cannot-the-same-can-be-said-of-the-lives-of these-sentimental-bikes-we-choose-to-ride-&-maintain?-DU69160 Link-&-Post-obligements-Y'all. Hope-this-morin's-coffe-dripped-runaway-spacebar; dries-up-&-gives-this-keyboard's-hypen-key-a-break.71319
1972 Norton Commando Combat Rebuild (12) - Dropping the front forks
5:01
The Mighty Garage
Рет қаралды 10 М.
Мясо вегана? 🧐 @Whatthefshow
01:01
История одного вокалиста
Рет қаралды 7 МЛН
It’s all not real
00:15
V.A. show / Магика
Рет қаралды 20 МЛН
黑天使只对C罗有感觉#short #angel #clown
00:39
Super Beauty team
Рет қаралды 36 МЛН
1972 Norton Commando Combat Rebuild (9) - Reassembling Crankcase halves
7:10
1972 Norton Commando Combat Rebuild (15) - Fitting piston rings
18:26
The Mighty Garage
Рет қаралды 9 М.
1972 Norton Commando Combat Rebuild (16) - Fitting the barrel
12:27
The Mighty Garage
Рет қаралды 12 М.
1972 Norton Commando Combat Rebuild (22) - First Start
5:45
The Mighty Garage
Рет қаралды 11 М.
Norton Commando Engine Rebuild. Part 14: Removing Cam Chain and Worm Drive
9:16
Classic Motorcycle Mechanics with Chris Rooke
Рет қаралды 1,2 М.
1972 Norton Commando Combat Rebuild (7) - Fresh Parts have arrived
4:39
The Mighty Garage
Рет қаралды 11 М.
1974 Norton Commando engine bottom end rebuild, Part: 3 Bottom end reassembly
1:03:11
Norton piston and barrel assembly with no ring compressor
7:21
James Comstock
Рет қаралды 4,9 М.