1988 Suburban #2

[@enlilstyxx1011]

Great videos, I have a 88 Burb with a Travel Quest kit, 3/4oak across the entire interior. I had the 6.0 but I ended up going with the original 350/700R4. I put a Eagle rotating assembly in the motor that I zero decked, Brodix IK heads, Comp roller cam( motor came with a roller from factory) Edelbrock AVS2 carb, I put a Aeromotive Stealth 340 pump in tank as I will one day go back to FI because its no fun pulling over to change jetting as you climb in altitude. My trans I went with a TCI full manual VB and 2200 stall converter. Hopefully I will have it going in the next few months.

[@jasaanarruda6800]

Sounds like a nice setup for sure. They are a lot of fun. I’m in the process of upgrading heads, intake, pistons and rods now. Shooting for over 700hp to the wheels.

[@user-dx9vd8fg7u]

Ok, that sounds amazing!! Very tastefully done. The whole vehicle. My dad had one of these and that’s what made me watch the 1st video.

[@jasaanarruda6800]

Thanks!

[@DavidMalloy-tk3dk]

Thank you i think i will keep it and also i have a 1994 short bed chevy truck 368,ooo miles on it body is cherry but a bad yr. for factory paint job it is so smooth driving got lucky when i purchase it. you have a sweet ride there i enjoyed your show.take care from the show me state.

[@SuburbanDMV]

I'm doing an LS 6.0 swap for my 92 K2500 Suburban. But will probably keep it stock with an ECU tune for now. Love your truck! Great build! o7

[@jasaanarruda6800]

Sweet! I just pulled the engine and installing, forged pistons, Holley high ram, prc 237 heads, e85 fuel system. Should be roudy!!

[@SuburbanDMV]

@@jasaanarruda6800 Rowdy probably will be an understatement. Lol, that's gonna be damn nice. o7

[@trentdawg2832]

I never used a pressure reducer on my power steering pump for my '74 nova it's been 4 yrs now with no issues.......... (knock on wood).......damn that's a beautiful 2wd suburban.........only a matter of time until you add boost......took me about 2 yrs till I pulled out my 5.3 and put in a 6.0 than shortly after that added a lsa supercharger. .....would have went with turbos but due to under hood room I just went with a supercharger for simplicity. ........I love it......works great with my terminator x max

[@jasaanarruda6800]

Thanks Trent, I just checked out your videos. Nice job!!

[@SWFabrication.]

Haha I just posted in your first video. Man, that sounds great. Awesome Sub and awesome job. Looking forward to the cam swap updates

[@waterboy540]

Great truck

[@jasaanarruda6800]

Thanks L1mp1n! I love working on it. It’s just a big toy. Lol

[@juniormints6454]

digital gauges are a nice touch cool feature

[@jasaanarruda6800]

They look great at night for sure.

[@Jac2Mac]

I was surprised to hear a scary buzzer when you started up this 1988 Suburban. I thought all Suburbans only used the chime tones by 1988.

[@jasaanarruda6800]

The buzzer is from the Dakota Digital gauge set up. I don’t really like any of their buzzer options. They are all scary. Lol

[@956MoE]

this is a goal of mine, i want to build one very similar to this!!! badass man!

[@jasaanarruda6800]

Go for it 956!!

[@renegonzales2186]

Sounds really good 👍

[@edwardtorrence5566]

Badazz,so this Suburban had 8 lug wheels originally?I'm asking because I own a 88 BB 8 lug suburban

[@jasaanarruda6800]

That’s right. I knew I was pulling it all out so it didn’t matter if it was half or three quarter ton.

[@joequayzar4592]

beautiful rig man! I'm Considering 5.3 and 6.0 for my 89 burban Ls swap. I'm just looking for reliability as my main goal. what made you decide to go with 6.0?

[@jasaanarruda6800]

I figured I would go with the extra horsepower and torque was the reason. Same size engine on the outside so it wasn’t any more work, just a bit more expensive. Good luck with your swap!

[@rodneybrown4594]

BEAUTIFUL TRUCK!

[@raybinker9472]

when your taking about reducing the pressure I saw you have the same brake lines and valve as my 88 Burb r10, I can't find new lines anywhere, nothing that I've ordered fits, I kept my 350 instead of my LQ4 for now. awesome stuff though

[@AceNos71]

Sounds awesome, great job!

[@jasaanarruda6800]

Since this video, I put a cam in it. It’s a little rowdier now, lol.

[@sauce6910]

whats the wheel size and offset your running and what suspension I have an 84 suburban 2wd im working in your looks amazing

[@jasaanarruda6800]

The front is Ridetech Strongarm tubular control arm kit with 2.5” drop spindles and Currie custom Ford 9” 63.75” wide. Wheels are 20x8 up front with 4.0” backspacing and rears are 20x9 with 3.25” backspacing. I had to roll the fenders a bit to tuck them. I mocked the front and rear out of wood to get it right.

[@sauce6910]

awesome thanks for the reply man is is custom suspension in back I thought I seen coilovers I want a good clean ride as my will be for cruise and long trips

[@jasaanarruda6800]

@@sauce6910 Yes, the rear is a cut to fit Ridetech 4-link kit with coilovers. I ordered the Currie rearend bare.

[@csmithbusiness]

You have an Instagram for the burb?

[@jasaanarruda6800]

@@csmithbusiness no I don’t

[@JohnSmith-qj4cf]

What do you think of the holley terminator x max or howell thks as I said mine lq9 t400 gear vender just got me a 9in with 35 spring axles no gear what are your please

[@jasaanarruda6800]

John I don’t have any experience with Howell so I can not comment but I can say the Holley Terminator Max system gave me the confidence to do the swap myself. If you have a TH400, you don’t need the X Max you just need the X since your transmission is not electronic. Good luck!

[@JohnSmith-qj4cf]

@@jasaanarruda6800 thks for your reply ill try the holley thank you again

[@dannylugojr3428]

Very cool 👍🏽👍🏽

[@PAUL_K]

Can't go wrong with an LS Six-O!

[@nando_74]

Can't wait!!!

[@mausha77]

Looks nice have a 91 suburban im working on want a newer engine put in it. Runs pretty good.

[@jasaanarruda6800]

It just takes a bunch of money and a bunch of time. Lol.

[@julianenglar]

how much dynamat did you need for the whole interior?

[@jasaanarruda6800]

I bought 2x Dynamat Extreme 10465 and had a little left

[@stevenray1986]

Does anyone know what kind of rims these are?

[@cameltoast]

He says it in his other video on it.

[@terrancesells3250]

Detroit Steel wheels

[@donniegardner6294]

Just out of curiosity..where did you purchase this vehicle?

[@jasaanarruda6800]

From a person in central Florida who purchased it from the Mecum Auto Auction

[@richsanchez3288]

BAD ASS!!

[@marcoschacon1768]

Sweet two

[@djverhulst]

cool!

[@blodquatsch]

Let us see her roll!

[@jasaanarruda6800]

Very soon

[@blodquatsch]

@@jasaanarruda6800 cool man! Awesome build!

[@cheeseymccheese7249]

Dam, take it for a scoot. Lets see some acceleration

[@jasaanarruda6800]

I need to install the converter and then get it tuned. Video will be after.

[@buckshotgeorge7201]

Shit I never heard it run!!!!! Beautiful!, but no sound!!

[@jasaanarruda6800]

There is sound. Thanks

[@drewcarfrae808]

For sale by chance?

[@jasaanarruda6800]

No sir

[@SuburbanDMV]

@@jasaanarruda6800 Nice! I always say ....NEVER. o7

[@BuySellTrade-g7i]

No cam ? That’s crazy

[@jasaanarruda6800]

Sloppy Stage 2

[@BuySellTrade-g7i]

Have you done anything to the burb since the dyno tune ? I’m really interested in your build because I just purchased a 86 LS burb myself

[@jasaanarruda6800]

@@BuySellTrade-g7i I just finished a D1SC ProCharger install with intercooler. I’ll post a video soon.

[@BuySellTrade-g7i]

Wow I have to see this…why not turbo ?

[@jasaanarruda6800]

@@BuySellTrade-g7i The main reason was lack of room for 4” exhaust plus I like the sound of a ProCharger.