1992 - 2000 Honda Civic EX Accessory Drive Belt Replacement AC PS Alternator Serpentine 1999

[@thiagoqcarvalho]

Your tutorial was the first one that I saw that teaches how to tighten the belts. Congratulations, that was really helpful.

[@JackofAllMasterofNone]

Glad it helped

[@whitneysteeves6947]

@@JackofAllMasterofNone you you guys have been

[@2006Mercury]

I cheated and used a lift in my shop but this video was extremely helpful I couldn't have done it without you thank you very much

[@drench7]

Part Numbers since it's not posted: Power Steering - 4PK0845 A/C - 4PK0820 Alternator Belt - 4PK0800

[@draynyb2511]

Life saver

[@TheChabm]

hi. are these part numbers "fit" the 1996 civic PH15 LXI? [philippine market release].

[@mauriciootis9746]

You prolly dont give a shit but if you're stoned like me atm you can stream pretty much all of the new movies on instaflixxer. Have been binge watching with my gf for the last few weeks :)

[@kabirthaddeus3688]

@Mauricio Otis yup, I have been watching on InstaFlixxer for months myself :)

[@ThonyHerrera4666]

goddddd blesssss you

[@Rexynator]

This video really helped me. I thought it was going to be more difficult than this. Thanks again. Not all heroes wear capes.

[@MegaHomieJ]

I wanted to thank you for the video it helped me a lot. I didn't even have to jack up the car at all and i didn't want to take off the top motor mount so i worked around it and it still worked out good. My car doesn't have the lower torque mount installed (i'm guessing it fell off while driving. I ordered a new one so I can install it next week) so I just slipped the old belts off and the new belts on, tighten and good to go. your video made it super easy and I think it only took me about 30min to 40min and I was done. once again thank you

[@swashtv3639]

Entire engine mounts don’t just fall off while driving.

[@kingiburu2778]

@@swashtv3639 dont they though.

[@devingarrity8148]

Lol. Scary

[@PyRoTECniQs]

i just got done doing this and i was nervous since it was my 1st time. I really appreciate that you took the time to upload this,thanks again .

[@jonasusma]

The only good video on the net on this process . outstanding directions beginning to end.

[@JackofAllMasterofNone]

Thanks

[@harrisdoesthings]

I might be late to the party but, there is a provision for a 1/2 drive socket to tighten the power steering belt instead of the pry bar. 11:48 next to the wire there is a square hole.

[@carsenfzj805]

Thanks g

[@truthseeking3818]

This video was perfect and helped so much. Surprising you need to take off two engine mounts just to get to some belts. Thanks a lot for taking the time to make this!

[@cyrilslugz]

good video,, all my belts broke off at the same time,, lol handy videos..

[@davegeorge7094]

Good show! I just changed thermostat and a 10mm gearwrench saved time, very tight spaces.

[@chrisp1558]

Great tutorial video, straight to the point no bs.. Good job sir. Thank u

[@sydneylane3129]

Thank you this is the exact model of my car too and im planning on purchasing the belts online this helped me figure out what ones i needed!

[@Zadan86391]

Thank u Jack! Definitely the Master aha Best how to video so far

[@ArturoMontes-m4v]

Thank you for this video , first time doing something this major to my wife Honda civic.

[@KiwamiJoryu]

Replaced the belts today, thanks to you. Big help your video, God bless you

[@JackofAllMasterofNone]

Glad it helped

[@BombaclaatGatofish]

Extremely helpful video for an amateur like myself. Thank you very much

[@joe25rs]

@Jack of all master of none, Very helpful video. Thanks for the straightforward delivery, clear instructions and simple videography. You have provided a very valuable reference for us shade tree wrenchers. 👍🏻

[@goodvibesonly1920]

Great job you make it look easy, I'm have a hard time replacing my ac belt man!!

[@TheRealSpeedWolf]

my serpentine belt and idler belt both snapped. Unfortunately, I can only find replacement belts for the 2001 to 2005 Honda Civic 1.7L models. Are they compatible with my 2000 Honda Civic 1.7L EX-R?

[@hooviedoovie5220]

just a btw, when there's more than one different belt, they're not called serpentine belts, a serpentine belt is one belt for everything like a 94 chevy blazer. other than that great vid!

[@topprotips5250]

mini hoov I have a strippped 14 mm bolt on side of my ac idler pulley it’s Stripped bad . Is there a way to get it off , there is no space and also do I need that ac idler pulleybolt on the side to put my belt back on so it can loosen ????

[@TOMA-ny7gg]

great video but why u dont show all the process?

[@MrMagicMike93]

I don’t get why anyone disliked this video it was pretty up front

[@overlandersnorthwest]

Did you do a video of the timing belt change? I want to change mine. This video was helpful

[@chinoin24]

Thanks for the info, appreciate it, great video :)

[@shkkrimp7344]

So how much of this do I have to do for just the ac belt?

[@playboii6000]

watch the video

[@cristianugalde6299]

Hello, since I don't know English, I would like a brief tutorial to install only the air conditioning (AC) girdle, it is only the girdle I need to change, could you help me with that?

[@ToddStephens-h3e]

Why do you have to loosen the 14mm bolt on the tensioner pulley? Cant you just loosen the adjusting bolt?

[@homerun3014]

Awesome video, so helpful!

[@MoLightBeing]

Thanks this vid helped me a lot

[@carnifex2173]

What’s that squeak sound after he starts it up? My cars making the same noise

[@wandamann8217]

Thanks for the good video the only thing that is bad is they put the alt belt behind all the other ones dad gum Honda’s from rod in ala

[@JackofAllMasterofNone]

+Wanda Mann yes. It is a pain to get to

[@skoomacat13]

And the engine mount running through the ac belt. Its been a pain in the ass.

[@Gumorisco11]

I have a quick question i have a 1998 honda civic DX and just today as i was coming back from the store my battery light came on then i completely lost power couldn't accelerate at all my lights turned on ... but when i tried to turn on the car it was completely dead even tho the battery had energy... would it be my timing belt that ripped ??.. hopefully it is

[@JackofAllMasterofNone]

Sounds like the alternator stopped charging.

[@Gumorisco11]

@@JackofAllMasterofNone possibly a new alternator??

[@_sousa_delsol]

Doing this job right now and those 2 bolts that hold the motor mount stripped the middle piece with the nut and washer missing can I just run no ac for now ?

[@DoktorFreaman]

Oh. Great video by the way. Best one. Make moar!!

[@martin4.665]

Are the ac belts and power steering belts the same for a 95 del sol vtec 1.6 sohc as seen in the video?

[@Mid-Ohio]

Any video out there on how to do the Alternator belt replacement on a 99 civic?

[@juanriat4056]

Do you have the torque specs for all these bolts please? Thanks in advance and great video. Doing this soon in a 2000 lx, hopefully it applies

[@JackofAllMasterofNone]

No I don't

[@654Crossman]

Gutentight. That's German torque spec for all them.

[@josephtovar010]

Does the ac pulley have a 14mm nut or is it a 12mm nut

[@smiley21577]

Just like you say 🎉🎉🎉

[@219Fishing]

Changed my ac belt and idler pulley then it started smoking bad until it snapped off the belt any idea what it could be . Ac pulley spins freely maybe I tighten the tensioner to tight ?

[@JackofAllMasterofNone]

Something is locking up. Try turning on the AC and see if you can spin the compressor. Is your tensioner pulley spinning ok? Also, everything has to be in alignment.

[@Alejandro22897]

Mine doesnt have the 10mm bolt to loosen tension for ac, is there a way around that ??

[@MazzyFd]

If I don’t have ac could I just cut the belt? Or do I need the belt on to have the car work properly??

[@JackofAllMasterofNone]

If you dont want AC you can cut it and leave it off

[@kiran-wh9wg]

I'm total how many belts are there ? Timing belt , alternator belt power steering belt and ac compressor belt ? Total 4 right ?

[@JoeRCV]

Really helpful video, thanks. Question, I put a new belt but I get squeaky sound turning the wheel. Can an over tighten belt cause squeakiness when making turns?

[@JackofAllMasterofNone]

Not usually. It's usually too loose of a belt that squeeks. Or there may be a contaminent on the belt like oil.

[@JoeRCV]

Jack of All Master of None Nice I see, thanks. Will try and find the culprit and get back to you with the answer

[@SgtEvarsmann]

@@JoeRCV hey man where you able to figure out your problem? I changed all the belts and my car does the same but only when its all the way to the right or left, sometimes it does it without going all the way but when the engine is cold

[@carnifex2173]

@@SgtEvarsmanndid you ever figure out what it was?

[@SgtEvarsmann]

@@carnifex2173 no man, honestly it only did it when it was cold, like in the winter. It looks like that's the case for others too

[@SgtEvarsmann]

where did you get that huge bolt for the mount? @6:37 seems to be a new one I am looking to get a new one as well

[@JackofAllMasterofNone]

It's not new.

[@libaaxalee]

good job.

[@jonathangordiantorres6608]

Thankyou 💯

[@mrmatress4953]

Thank you

[@dkinley334]

Is anything connected to the ac belt other than the compressor?

[@humanspdr6511]

I was told I needed to buy 2 belts to replace my drive belt but now I’m confused because you said 3

[@JackofAllMasterofNone]

Depends on if you have AC and power steering.

[@silviamatsuura3630]

Hello, I am trying to put a new ac belt and cannot remove it because it's a huge bolt. Do I need to buy an impact wrench?? thanks a lot

[@drwatson1234]

Wrench with a big pipe fitted over the end. You most likely could not fit an impact wrench into that tight space. Leverage/ physics - are your friends!

[@SosaMusik]

Can I just losen the ac belt and take it out of place so I can put the alternator belt on, instead of taking it completely off with the mount. I’m trying to a blind removing the mount

[@nathanfleming1226]

The ac belt goes around the lower mount so you can get an alternator belt in and out without removing the mount and ac belt

[@otot7374]

amazing!

[@jcaleca60]

The video is excellent but put a block of wood on the corner of the oil pan

[@jcaleca60]

When you go to Jack it up

[@awesomepacker1216]

Any one know the size of the alternator belt

[@edgarleon5650]

Can I just cut off ps and ac belts save my self sometime to get to the alternator lol I’m willing to drive with no ps and ac

[@JackofAllMasterofNone]

You can.... lol

[@onetwothree4148]

Good luck parking without power steering. It's not the same as driving a car that was designed without PS.

[@calvo147]

Good video but trying to be more pacific next time

[@willemkanon4020]

Is this an automatic or a manual? I've got a 2000 civic the engine compartment looks exactly the same, I want to know if I can get cruise control on a manual. It might not have been an option in Europe or something because I can't find a manual car with cruise control. Also I need to replace these belts so thanks a lot for the tutorial.

[@JackofAllMasterofNone]

Mine is a manual and had cruise control

[@alext.4525]

Apologies if this was mentioned, but how long would you estimate this job takes? I’m relatively experienced and everything depicted in the video seems well within my comfort zone. Just looking to budget my time accordingly. Thanks

[@JackofAllMasterofNone]

About an hour taking your time

[@skoomacat13]

Do i really need the crowbar if I'm just trying to get an ac belt on?

[@JackofAllMasterofNone]

Probably

[@cooltu2000]

is this same as acura integra 1992

[@RobertBrousseau]

time stamps and tool list would be helpfull

[@Kinkajou1015]

I'm going to assume the engine can't start without the Alternator belt... I guess that's the belt that broke in my Civic last night. Also I'm going to guess the shop I had replace belts 18 months ago didn't do it right because I don't think my AC belt was even there when I poked my head under the hood. Sadly I can't repair it, I don't have the skills, strength, tools, or money.

[@JackofAllMasterofNone]

It could run off of the battery a short time without an alternator belt, but would not charge and would quickly drain the battery.

[@Kinkajou1015]

@@JackofAllMasterofNone Maybe that's why my low battery light was flickering when my car broke down, the belt had broken earlier and it couldn't provide enough power...

[@sea__big__919]

I see the title says EX but is it the same for the DX i know its a dumb question im just not that smart lol

[@JackofAllMasterofNone]

It's a different engine so maybe different

[@maxxmich]

u do t need to take off any motor or trans mounts to replace belts

[@kacasio1]

Those headlights are shiny, are they new? If so, where did you get them?

[@JackofAllMasterofNone]

+Kevin Acasio ebay. They are eagle eyes brand. Make sure you get the eagle eye ones and not the cheap crappy onea. I got them from partscontainer for $ 61.52

[@kacasio1]

Jack of All Master of None thanks, do you have a link? I saw a set on Amazon, and they had pretty fair reviews.

[@paulmartinez4720]

On its oil pan I mean

[@bFORCe2003]

You should've showed video of you taking all the things off first.

[@jockellis]

Wish I had power steering.

[@maxxmich]

next time... take the wheel off.. more access

[@tommygutierrez66]

Sacar Samper de acura 1997

[@paulmartinez4720]

Seems crazy unsafe to jack a car.

[@paulmartinez4720]

On the oil pan

[@JackofAllMasterofNone]

I didnt jack the car on the oil pan. I supported the engine with a block of wood under the oil pan when removing the mount. This is standard procedure for this type of repair. Additionally the oil pan is aluminum and very strong and would support the weight of the car if necessary

[@paulmartinez4720]

@@JackofAllMasterofNone oh okay well I got it done without doing so, I just had to remove my power steering pump to give me some room to loosen my AC belt but I believe you would indeed have to remove a mount in order to change the AC belt as it was trapped in between the mount, preventing it from being pulled out.

[@Headtwisterz]

@@paulmartinez4720 yes, but How did you guys put the new motor mount back in? It was easy to take the old one out because it was worn out, but what else do you have to do? in this video, it does Not show HOW the motor mount was put back in.

[@adamrodriguez5741]

This Video Was Not Helpful At ALLL

[@01nmmn]

Don't see how you put the transmission mount 🤔🤔🤔🤔