Have Sloppy Steering ? Well Today I Have The Fix For You , Cunningham Machine Lower Half Shaft With U-Joint. Unbolt Your Stock Shaft And Bolt This One Up In Its Place! www.cunninghammachine.com/pro... IG- @Renteria_carlos23
Пікірлер: 50
@Icysoles603 жыл бұрын
Thank you so much for this vid. I have had the swanging issue for the longest lol, cant wait to make this upgrade
@jaywestfall34392 жыл бұрын
Awesome video, y'all. I have one of those to install on my 1998 C1500 ext cab. This answers every question I had!!! 👍🏻😁🙂
@Rbenterprises4 Жыл бұрын
I just replaced mine with a Dorman rag joint shaft. The hardest part was getting the top bolt out since someone used an impact and rounded the bolt! I used an Irwin bolt extractor, replaced the bolt and nut, then pushed the boot on the new shaft back far enough to go up into the column. I broke the plastic collar off since I did not push it down far enough to clear the frame. Oh well, it works great! No more steering wheel slip!
@sidewayzindustries2613 Жыл бұрын
Nice to hear that man crazy how much it makes a difference , no slip anymore!
@georgiabigfootАй бұрын
@@sidewayzindustries2613do you have an update vid about this? Did this remove the play in the steering wheel? Thank you
@cobaltsslsj5891 Жыл бұрын
thanks for the great video that was complete
@joelcastro14413 жыл бұрын
Did mine and couldn’t get it to slide out as easy as yours. Had to remove the bolt from under the dash on my 96. Great video.
@sidewayzindustries26133 жыл бұрын
Appreciate it , doing a giveaway at 2k subs!
@scottholt35452 жыл бұрын
Good video. I totally over looked that on my 98 gmc Yukon. I replaced the tie rods, pitman arm, idler arm, sway bar links and still have sloppy steering. I am going to order this part right now. Thanks man
@Morgancj2 жыл бұрын
Gimme an update bro I’m in your same boat
@Beek882 жыл бұрын
I did the exact same thing. New everything even wheel hub bearings, control arms ball joints inner and outer tie rods...shop still wouldn't line it up. Both wheels had side to side play, but at the same time
@Morgancj2 жыл бұрын
@@Beek88 you got a new rag joint ?
@scottholt35452 жыл бұрын
@@Morgancj I got a lower steering shaft from a 96 Jeep Cherokee. Only slight modification was needed. Drives so much better. I still need to get a steering damper. Once I can find a center link with 5 holes from a 3/4 ton GMC suburban.
@georgiabigfootАй бұрын
@@Morgancj2 years no answer is a bummer.
@czarredd2 жыл бұрын
Cunningham Machine site says that if you have the aftermarket Dorman upper…this lower won’t fit without modifications. I have the Dorman upper and interested in knowing what modifications need to be done for this lower to fit and work properly? Thx!
@brandonperez48473 жыл бұрын
So I don’t need to get the same old style model one 98 one with the round steering coupler on it?? What difference does that make
@Lucky.4205 ай бұрын
Some of these gear boxes have an alignment pin. I used a Dremel and cut it off. fit percent after modification. For anyone that’s wondering .
@robertcarlos782 жыл бұрын
How did it come off I loosen both bolts. You didn’t show how you took it off
@astronomical132 жыл бұрын
Maybe instead of showing 2 minutes of spraying and wiping a plastic part that wasn’t even used in the end you could have used that time to actually report on how much this improved the steering performance.
@shannonkiser77403 жыл бұрын
How did you get it to slide all the way on the steering box shaft? Does your steering gear box have the alignment pin on the end of the shaft?
@truggy6072 жыл бұрын
you ever get yours on? cant get mine
@Lucky.4205 ай бұрын
I used a Dremel and cut it off. fit percent after modification. For anyone that’s wondering .
@garybermudez63922 жыл бұрын
I did get pulled over lol 😂
@josemandujano4720 Жыл бұрын
I haven’t but it was funny because I thought I was the only one that was bound to get pulled over for it 😂
@fpsnashamdan73623 ай бұрын
Can the same action be taken for 92 Buick Roadmaster ???
@workingclassbear65232 жыл бұрын
Spread the lower side where its pinched to the box and it will fall apart for you.
@barrycowan19972 жыл бұрын
What if I don’t have those tools?
@asteroidink3 жыл бұрын
How much improvement? Worth it?
@sidewayzindustries26133 жыл бұрын
Yes , tighten up the steering a lot
@convoymusic71412 жыл бұрын
Would it fit a 95 2 door Yukon 4x4
@sidewayzindustries26132 жыл бұрын
Yes
@raymondtrevino63703 жыл бұрын
Would the plastic hard cover not work ? I saw you installed on table but final ending didn’t have cover on
@sidewayzindustries26133 жыл бұрын
Yeah I think put it in the video , to remove the lower plastic , doesn’t work only the upper rubber will
@raymondtrevino63703 жыл бұрын
@@sidewayzindustries2613 thanks for the video
@chriswhitcomb82483 жыл бұрын
how long did it take them to send it out to you
@sidewayzindustries26133 жыл бұрын
Not long , heard they’re on back order at the moment
@chrisescobar19853 жыл бұрын
Why haven’t you uploaded bro
@jessealcalarealtyone2 жыл бұрын
Will this part work for a 94’?
@sidewayzindustries26132 жыл бұрын
Yes I believe they make a specific one for those years
@Ski.the.slayer Жыл бұрын
It’s better for you and cheaper to grab one of a Jeep Cherokee XJ get one at pick a part for the low should be plug and play and it’s the universal u joint
@lisandromelendez95453 жыл бұрын
What web site you got that from brother. That's what I need
@sidewayzindustries26133 жыл бұрын
Link should be in the description
@hugodelamora87333 жыл бұрын
Would that fit 93
@sidewayzindustries26133 жыл бұрын
Yes there’s a specific one for 88-94 and 95-99
@YouSoundButtHurt3 жыл бұрын
@@sidewayzindustries2613 I have a '95 but it's pretty much the same as the older trucks but with the newer interior. Is that why the '95 needs a different shaft because of the interior update?
@robertcarlos782 жыл бұрын
On 2:28 it don’t just come out and at 2:32 you had it off
@mikewilson69062 жыл бұрын
Adjustable ranch lol
@jwold112 ай бұрын
No offense but with 2 of you there you could have move the camera in a way for viewers to see what you're doing. Not very helpful.