1998-2002 Honda Accord Windshield Wiper Motor and Linkage Transmission Diagnosis and Replacement DIY

[@CuriousCaine]

Very clear without being overly long or wordy. While I'm a seasoned DIY'er, it's very comforting to see what's involved before diving in. Thank you.

[@lyndseecooper8942]

Just followed your video to install this on my car (2000 Honda Accord) after my wipers stopped in the middle of a snow storm and got the new part at the junkyard. It worked beautifully!!! For a female that knows nothing about cars but is also too cheap to have someone do it for her, this is exactly what I needed. Thank you thank you!!! Liked and subbed!

[@mrdragancelan]

Glad I could help!

[@Al_Ting378]

Thanks for your video. I was able to easily disassemble and get to the linkage assembly. Two of my linkages were broken causing significant flop of the wipers. Rather than buy A new assembly, I just went to the auto parts store and bought a $10 pack of generic nylon bushings and the problem is completely fixed.

[@cggilbycg]

Thanks for this video man! My wipers work again! I didn't replace the whole linkage though just the bars with the ball and sockets. But your instructions on how to remove the linkage was clutch. Thanks again!

[@mrdragancelan]

Glad my video is still helping people 7 years later.

[@mikeflowers6278]

Thank you, Dragan, for this excellent and informative video. Our 1998 Honda Accord on Maui needed this linkage replaced and the local Honda dealer wanted $329 for the part, plus who knows how much to install it. $32 from rockauto.com and about an hour of my time got the job done. Your step-by-step explanation made the job an easy one. Even my wife was impressed! Thanks again for posting this video - it save me a bundle!!

[@bbwrenn]

Needed help getting to and removing the motor. Even though it wasn't the focus of the video you still helped me get it done. Thank you!

[@OMG-yw4fl]

Thanks for this video. I just replaced the motor itself and the video showed me where the rest position was on the linkage itself, which needs to be set before adjusting the wiper arms after a wiper motor replacement.

[@ezpeteyt]

Ordered the assembly online for about $40 and installed it in 30-45 minutes thanks to this video.

[@CineSolutions]

Hey, I watched ur great video and was able to fix my wiper problem in my 2000 Accord. I was so lucky because I only had to replace one of the strut-arms and not the entire assemblage for only $10. Thx so much for taking the time to create this video for the world!

[@woogaloo]

Perfect video. Mine are going over when they wipe and hitting the cowl so I’ll have to open it up and see what’s going on - if it’s the linkage or the motor and linkage.

[@MarkStrecker]

Thanks for posting! It made my job a lot easier, and saved a few bucks as well!

[@mrdragancelan]

+Mark Strecker No problem at all. I'm glad it helped. Thanks for watching!

[@aquariunneo5976]

Thanks for share.. You saved us money by doing the hard work and posting it.GOD bless you.

[@MrStudzdog]

Thanks, very helpful. Always like to see what I'm getting into before I start. Nice video

[@mrdragancelan]

I'm glad it helped!

[@spahncamper]

Thank you for making such a clear and concise video!

[@jaylensmith5936]

Thanks for posting. This will save me some $$.

[@mrdragancelan]

You're welcome!

[@caliemckenzie4447]

After getting it unstuck a few times got it done thank you

[@flipscoldjah]

Thanks for posting this man! It really helped me out!!!

[@mrdragancelan]

+flipscoldjah No problem at all. I'm glad it helped!

[@suaveTech]

im gonna weld that together. forget having issues with that popping on and off.

[@MrYimean]

So I done everything u did up until the part where u fixed the disconnection...mine is a 2001 es accord and the disconnect looks different I will send a picture if I can but if u have any suggestions I'm open to it because it's a simple disconnect but I'm having trouble reconnecting it

[@JohnLien]

Thank you!! It was very helpful!

[@mrdragancelan]

You're very welcome! I'm glad it helped you.

[@chuck5185]

Super helpful! Thanks!

[@dreamliner1977]

Thanks for posting! Question, was the aftermarket linkage OEM Honda or another brand? I've read on some forums that you can usually get away with just replacing Rod Unit A (the top linkage).

[@mrdragancelan]

+dreamliner1977 The one I used is an aftermarket linkage. Link for it is in the description. You can get away with replacing whatever link is affected but it depends on what has actually failed. I had a Honda Civic where one of the links actually broke right in the middle. But typically with old linkages like the one in the video, the joints are worn and are more prone to popping out. So I'd recommend replacing the entire linkage if this is the case for you. And thanks for watching!

[@dreamliner1977]

+Dragan Celan Thanks! I missed the link the first time.

[@deandailey7482]

Great Vid! I’m in the process of replacing the linkage assembly. How do I ensure I order the right part the first time? Thanks! EDIT: just saw link to part. NM. 😁

[@mrdragancelan]

Just make sure you order the part for the same model year of the car you're working on and make note of whether it's a sedan or coupe as the wiper linkage may differ between the two body styles.

[@deandailey7482]

Dragan Celan will do! Thanks again for this great how-to!

[@mrdragancelan]

You're welcome!

[@gcampbell6126]

Will this work on a 2000 Honda accord 2 door coupe thank you!

[@mrdragancelan]

G Campbell I don't see why it would be any different. I believe it is the same regardless of whether it is a sedan or coupe. You may want to look into it just to make sure.

[@ZealousMystique]

you are awesome thank you

[@mrdragancelan]

ITsystemAssociate Thanks for the kind words! I'm glad it helped.

[@jimkalfakis9893]

Thanks man!

[@mrdragancelan]

+Jim Kalfakis You're welcome!

[@tilli2971]

When my blades are not in the intermittent mode they slam hard on the down stroke and on the upstroke they stop in random places sometimes going past the windshield and other times approx 3" away from the end of the windshield. Do you know where I should start looking? Thanks

[@mrdragancelan]

Sounds to me like your wiper arms are not positioned correctly on the motor shaft and thus don't have the proper start and stop positions. If the positions vary, then chances are that the splines on shaft of the motor aren't doing a good enough job to prevent the wiper arms from spinning on the shaft. I'd recommend looking at the video at the 5:00 minute mark to help you position the wiper arm correctly on the motor shaft. That and a slight over-tightening of the nut on the motor shaft might help the splines dig into the wiper arm (tapered cylindrical surface) to prevent it from moving out of position. Hope this helps.

[@tilli2971]

Thank you for your response. I will check that out first!

[@amaresatterwhite]

I have a 99 Honda Accord EX 4CYL 2.3L and my wiper blades smack hard on my front diver side window at medium to high speeds. Would this be my motor, linkage or something else possibly?

[@mrdragancelan]

You're going to have to clarify what you're saying. Do you mean your wiper blades are hitting your A-pillar?

[@amaresatterwhite]

Yes, the longer wiper blade does hit my A Pillar as well as can reach past it and hit on the diver side window when at higher speeds. Also when in motion, at times the wiper blades doesn't reach back down to its normal position before coming back up. As a result, when turning the blades completely off, they sometimes rest a little higher than they should onto the front windshield and I have to manual slide down to where they should correctly be.

[@amaresatterwhite]

I only have this issue, at medium to high speeds or when it's heavily raining as if the wind/rain is to much for the blades to stop itself from going to far.

[@mrdragancelan]

So chances are that the crank link has slipped on the splines of the motor shaft and thus has lost its correct home position. You'll need to dismantle the linkage and carefully look at 6:30 in the video to make sure that the crank link is tightened correctly in the home position. When you re-tighten that 17 mm nut, you may need to torque it down a bit more than necessary to ensure the splines of the motor shaft dig into the crank link and, thus, preventing it from slipping in the future.

[@mrdragancelan]

Yea sounds like the splines on the motor shaft aren't doing their job. If you have the time and know-how, I'd take it out and have a look and maybe try what I suggested in my earlier comment.

[@HowTwo007]

my wipers work on the medium and fast setting but the lowest setting which is the interval one. the one that you can adjust the timing with does not work. Any advise someone can give me to narrow down the issue

[@mrdragancelan]

It doesn't work at all or you just can't vary the interval?

[@HowTwo007]

the eium and fast speed was working but the intermittent one was not. i tried it again yester day and all seemed to work fine so i am a little confused. wipers do seem a little bit slower on all speeds though some maybe some part of the wiper system is about to need replacing

[@mrdragancelan]

When you tried it again yesterday and everything worked, was the engine running? If not, that would explain why the wipers were moving a bit slower. The extra voltage from the alternator help move the wipers that much faster when the engine is running.

[@theonlydubbace8279]

so if my drivers side doesn't work, can I just put the linkage back on?

[@mrdragancelan]

Sure. I wouldn't expect it to stay on for long though. But I guess it's a good/cheap temporary solution.

[@theonlydubbace8279]

Dragan Celan would you say that's what the issue is?

[@mrdragancelan]

That's what the issue was in my case. I had bought the part prior to replacing the linkage so I figured I would replace it anyways even if it was temporarily fixable.

[@theonlydubbace8279]

Dragan Celan thanks man

[@1urquico]

thank you for sharing

[@mrdragancelan]

You're welcome!

[@fernandezmarquez6638]

I have a problem with the wipers not going on I bought a new wiper motor and installed but still not working I don't if it's the switch from inside the car ,,, and it's not the fuse I checked I need help please

[@mrdragancelan]

+Fernandez Marquez Does the old wiper motor work still? Is the relay good?

[@fernandezmarquez6638]

Dragan Celan the thing is idk where's the relay

[@fernandezmarquez6638]

And yes the old motor work

[@fernandezmarquez6638]

But I turn the switch for the wiper and it won't go

[@mrdragancelan]

+Fernandez Marquez If the old motor works and the new one doesn't, then we know the switch inside the car is functional and not the problem. Otherwise, neither motors would work. It sounds to me like the new motor is the problem. Why did the old motor work but the new one doesn't? Was the connector plugged in all the way when you installed the new one?

[@that1techguy785]

Mine work but they make a clicking sound every time they move any idea on what it my be?

[@mrdragancelan]

That1TechGuy Not sure. It may be joints that are loose and ready to pop out of place or it could be links contacting each other. It's tough to say without seeing or hearing it.

[@kiewainevans5111]

I did the exact same thing and mines still not working

[@italianozuzu1232]

Bushings are the ones that go bad no need to changue all the assembly just the bushings

[@Bloodtypewhiskey]

getting the angle on the wupers again is the problem

[@williammize8270]

Mine not motor its the arm only 3/4 way cross windshield annoying in my side too not passengers

[@PorscheRoseSylveon]

This just happened me to. And at the worst possible time.

[@laythb3323]

found the part onn ebay for 26$, cheapest one i could find.

[@fernandotejeda7529]

es diferente para un honda acorrd coupe 2003

[@mrdragancelan]

Sí. 2003 es el comienzo de una nueva generación del modelo Accord. Así que el procedimiento en el video no se aplica.

[@williammize8270]

Something else

[@Youngnotorious1]

So my windshields get stuck up. But my transmission still works? What would it be the tab?

[@mrdragancelan]

+Young Notorious It sounds like the splines are in poor condition and are allowing the wiper arms to slip on the shaft.

[@Youngnotorious1]

Dragan Celan how much would that cost to get fix or can I fix it on my own?

[@mrdragancelan]

It depends. Maybe all that needs to be done is to retighten the wiper arms nuts so that the splines on the shaft properly engage the wiper arms. But if the splines are beyond repair, you may need to replace the whole wiper linkage transmission. It all comes down to your capability and confidence.

[@Youngnotorious1]

Dragan Celan my wipers just get stuck up and don’t go back down what’s right with it? I need to know what it is and how much is it going to cost?

[@Youngnotorious1]

It’s 2005 Honda Accord