1998 Yamaha Grizzly 600 4x4

Brought this Grizzly back from the dead. Just by cleaning it up basically.

[@doobyboy21]

Got the same ATV ! With the same darn problem... I also had gas in my crankcase... And almost every darn screw was rusted... This ATV was mostly used for beach rides... Can't wait to finish fixing it ! Damn parts take forever to get to Canada ! Nice helpful video bro ! Thank you !

[@misplacedcaper9662]

You're stripping the screw heads because you're using a phillips screwdiver on JIS (Japanese Industrial Standard) screw heads. They aren't the same.

[@DIUBrandon]

Thanks!

[@RICHIE_RICH89]

Those hoses are all normal bottom ones are overflow top is choke vent there all fine. The high so they dont suck water.

[@eds1994fatboy]

I have a 99.If you don't pull start it just right.yank the starter until its past the compression stroke....THEN PULL....it will pull your arm out of socket.These also have a lot of valve train noise....that my dealer says is normal.

[@scrappy-watchentertainment3875]

yea lmao i have a 99 and i folded the pull start lever when i pulled lmao everyone else called me a pussy and then ended up not being able to do it either lmao

[@rc_p5192]

Agree on that pull start. Thank god the previous owner warned me. Still fucked me up once though lol

[@TSkin71]

How long did it take you to install the new carb and put back together again? Trying to decide if I want to TRY this. Thanks.

[@47927411D]

Use an impact driver on the screws that seem too tight...works everytime

[@amarmadison1202]

What is that thing on the inside of the pull rope

[@oby-1607]

Wow. This is the video I was looking for. I have a Yamaha 660 and the carb is leaking. Same story as yours. Did you find out what all the loose hoses were about that you showed in the beginning. I want to keep this 660 a long time as it used to be my brothers before he passed away.

[@JLafix]

Don't really remember that but I think I recall it's maybe just a vent hose but I can't say for sure either way that machine ran great

[@sudo936]

the hoses don't connect to anything they are vents and or over flow drains. You can connect the crankcase breather into the air filter box if there is a spot. mine doesn't have a spot just venting higher than possible water level.

[@robrobertson8124]

I have the same bike but 1999 I changed the carb and throttle cable. Now there is a lot of slack in the throttle cable any advice on how to adjust it to make it tighter

[@JLafix]

Sorry I don't have an idea without looking at the situation

[@blv935]

at 15:16 on the inlet of the carb there is two small jets(?)... my carb is spitting fuel out the hole on the right side of the carb.. the carb is new, do you have any idea why this is happening ??

[@JLafix]

No sorry I don't know

[@youtub857]

Just replaced my carb and I'm having the same issue did you ever get it solved??

[@zachcam797]

Can you post some links to these parts you bought? I have an ‘01 Grizzly 600 that needs some of the same parts you installed on yours.

[@JacobBitner]

Partzilla

[@nowayhunting]

i have the same atv. had the carb rebuilt and now it idles like it is running wide open. someone told me to check for air leak. if it had an air leak would it idle at wide open speed? and would it be on the intake side or the manifold side? thanks.

[@JLafix]

A carburetor Need a mixture of fuel and air to make the engine run correctly Yeah it has nothing to do with the engine RPM level As far as getting too much air or not enough air . So if the engine is At high RPM while idling The 1st thing I would check is the idle adjustment screw on the carburetor. That machine is just a straight up engine with a carburetor no computer involved To command more fuel because of an air leak. So just check your Idle screw or maybe even the throttle cable Out of adjustment.

[@billdeatherage9492]

@@JLafix thanks.

[@kevinmackenzie3694]

I was wondering if you had a video on how to fix the brakes on your machine

[@JLafix]

I don't. Not my machine.

[@allensnook7760]

Just watch any utube.vid on any brake repair for atv,such as warriors,big bears,iegers,they are all pretty much the same most have drum rears n disc fronts.for disc mostly just bleeding out air or bad fluid fixes them.some are drum both ends usaully older atvs.they just need new pads or slave cylders.fairly easy.you might get away with just tightning cables but not always good luck!!!snookie pa.big bear owner💥👍💥

[@fourbyfourer]

They're NOT Philips screws they are JIS screws!!

[@riderr2035]

Hey sell it to me bro

[@fourbyfourer]

You will never start that thing with the rewind. Yamaha does not know how to make a bike that will start easy with the rewind.

[@joshmcnutt1914]

I have but it's a pain

[@ericbaldon8566]

Vice grips dummy