How to Replace Front Window Regulator 10-17 Chevy Equinox

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@richheitzenrater6491]

Great walk through. Probably saved a small fortune at a garage.

[@jimwells4240]

NICE video....the manufacturers of late-model stuff like to hide things. Thanks for publishing this.

[@KidFriendlyGaming]

GM vehicles are so easy to work on too

[@trailerparkkings2041]

Nice job. I'm using your video to complete this job confidently.

[@byurgullwing3881]

Great video. I wouldn’t have been able to do the job without your guidance.

[@KidFriendlyGaming]

Great tutorial. I just did mine with your assistance!

[@ABrown-wh7ql]

I used ur tips and windows replaced…Thanks 🙏

[@KidFriendlyGaming]

Pro tips: tape window up. Loosen the clamps slightly before trying to attach to window. Bolt the rails in tight because that should align the clamps to the window. Attach the door panel temporarily to turn regulator on to get clamps up to the window and then tighten those. You dont want the regulator to have clamps all the way up when u install them. Make sure they are like 3/4 the way up and then turn car keys on, put window control up to mate clamps to window and then tighten. My window was stuck all the way down so i removed all the rail hardware and pulled the window up by hand.then I started from there

[@RickN816]

I have a 2013 Terrain and am needing to replace the window of the front passenger door. ~3:15, when you tape up the window, would I be able to slide it down then pull up to remove the broken window and do the opposite to install the replacement? Then continue at the point where you reattach the window to the track?

[@dwaynebodzenta7994]

Great video. You guys are forgetting two things which made this change alot harder than the video. 1. The window has to be all the way up, otherwise you will not be able to have acess to the the two bolts which loosen and tighten the two clamps to the window. My Equinox the window would come up about two inches short to the top which made acsess to the two bolts a pain. Thank god I had tools that could reach down and loosen these two bolts 2. the replacement part has to have the two guides for the window near the top. It has to be in a specific spot to get things to line up. My didnt. So you have to take the whole thing back out and connect it to the electrical connection and run the regulator and get them in their right position other wise the screw holes will not line up. 😀

[@1AAuto]

+dwayne bodzenta Thanks for the tip! We'll pass this info along to our production team.

[@Rittsx2]

I also greased the window tracks and cables - and put locktite on the screws

[@adrianthebeastlycreature]

Very helpful video, I got everything back together, but I can’t get the pins to reclip. Tried my hand like you did and also tried a rubber mallet with no luck. Also tried closing the door pretty hard in hopes that that might work, but the bottom is still loose. Any advice?

[@dbproductreviews6319]

I took apart the panel on my video today, I just posted, I think it's best to ensure the clips are directly mounted on the inner side of the panel as opposed to the actual door it self I had this problem too, but realized the gray clips need to be mounted on the panel first then re-assembling everything together.

[@mateobrynn5792]

Great video, very helpful. My problem is that I need to know how to replace the regulator with the window stuck all the way down. I can’t get it to budge so as to lift it all the way up and out of the way of replacement. Any thoughts? Thanks!

[@jimwells4240]

The window won't move at ALL with the clamps still holding it. If you are going to replace the regulator assembly (and already have a new one standing by), I'd be very tempted to cut the cables that go from supports to motor/gearbox assy. That ought to free it up.

[@jimwells4240]

or you could figure out a way to loosen the clamp nuts....your choice

[@KidFriendlyGaming]

If you remove all the bolts from the arms, the clamps on the window wont be attached to anything and u can pull it all the way up by hand. I removed my stuck clamp once i got window taped

[@red2965]

Nice video enjoy good instructions I just hate this type of system....wish Chevy would have took notes from mopar where all you need to replace is the motor not motor and regulator. Just asking for more trouble and money the way I see it. BTW mine is a '11 LTZ What is the auto lock my Lock for the doors are on the dash!

[@HeathOrrell]

Excellent video. Just what I needed to complete this repair on my vehicle. Is there any way you could do an instructional video on how to replace the interior door handle on this vehicle as well? It is the exact same door style/panel as the one in this video. The handle is held in place by plastic, melted rivets/fasteners and I could use some guidance on how to get it replaced the right way. Thanks for the great videos.

[@1AAuto]

+Heath Orrell Thanks for the support! Even though this is not a 2012 Equinox, the steps might be similar in this video: www.1aauto.com/how-to-install-replace-inside-door-handle-chevy-equinox-05-09-1aauto.com/video/1371

[@Mark-s2v]

Is it the same as the 2019

[@moy3613]

When i purchased new regulator to replace I noticed new regulator had window clamps positioned midway on tracks. How do i move them up to line up to bottom of window since window is now taped?

[@0714laedee]

Nice and easy

[@lacholozano7730]

Have you had any problems when you only remove the small motor if the regulator I could not put it back,seems like if is no fit?

[@Mark-s2v]

Definitely different for 2019

[@mikekotarba5828]

nice video thank you

[@1AAuto]

+mike kotarba Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@ags4444]

Can the motor be replaced without taking out the regulator?

[@1AAuto]

+Andrew S The window regulator should be taken out for the motor to be installed. Hope this helps!

[@yausaptheshasuabary180]

You ever do the motor replacement?

[@daniemay9321]

What do I do if I just need to pop my window back into place? It got stuck the other day, and wouldn’t go back up. My brother pushed it up, and I think he pulled it up to far, and now it’s just loose

[@cherokeendnboy]

Can you not just replace the motor?

[@JDel709]

Does 1A Auto carry this item?

[@1AAuto]

+Jeremy Luthy I do apologize but we do not carry the regulator.

[@bubonicblanket]

direct links to the parts and tools would be cool

[@1AAuto]

+Art M Thanks for the tip! We'll pass this info along to our production team.

[@hunterplayshd3820]

So you show taking it out but not actually replacing the regulator? Just taking it out and reinstalling the whole assembly? Lol