How to Replace Power Window Regulator Motor Front Driver Side 01-07 Toyota Highlander

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@miketyree683]

Great video. I used this to replace the front passenger regulator in my 2004 Highlander with no problems or issues. Many thanks.

[@1AAuto]

+mike tyree Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

[@melodylovelake3806]

Thank you thank you thank youuuuuuuuuuu sooooo much for this video!!! I just bought my first car and the driver side window was not going down! THIS HELPED ME ALOTTTTTTTTT❤ THANK YOU SOOOOO VERY MUCH.

[@louisianaguy2661]

Extremely well made, informative video. The window on my wife's 2006 Highlander would not go up yesterday so I will be replacing the window and regulator assembly. This video is a tremendous help.

[@1AAuto]

+Louisiana Guy Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

[@MIdaffy502]

This video was a huge help to me, the drivers door on my 2006 Highlander was just replaced because the original one rusted away, so they replaced the door with a used one. However the window rattled when rolled down, and made terrible noises when rolled up. It appears the Body Shop didn't take the time to tighten the back window bolt. Now I'm a Happy Guy, Thank you.

[@1AAuto]

+M Rose Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c

[@highsierrabassplayer]

Thank you so much, dealer want either $370 for driver's side regulator parts and labor, or $760 for driver side motor R&R. Turned out the bolt holding one side of the regulator fell out. Thanks to this video, I purchased your trim tools and had it fixed in about forty minutes. Oh, I did not need to take off the two cables going to door and lock opener, and I also re-lubed regulator with lithium grease...that was another $8 for that:)

[@ashgall8118]

By far the best video of changing the regulator I have seen. Very clear explanation of changing the regulator from start to finish. I've definitely subscribed.

[@1AAuto]

+True Believer Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com

[@chrlmlln9018]

Thank you so very very much for this amazingly clear and perfect most helpful tutorial and instructional video for how to replace the Power Window Regulator Motor! Best regards from Sweden! God bless you all!

[@sisirajaya]

I am impressed with the video and the fact that the technician installed factory bolt made my confidence about 1A Auto even more. Thank you.

[@1AAuto]

+Sisira Jayasinghe Thanks for checking us out! 1AAuto.com

[@puddintanejingleheimerschm9389]

If the motor isn’t working, how was the window able to move to the position you need by pressing the window up down button? If the window won’t move at all but makes a clicking noise, is this caused by a different problem other than the motor? The fuse has already been checked and is fine.

[@dfromw3240]

My biggest fear was synchronizing the up/down stops but now I know they will sync themselves by following these instructions thanks

[@dodoboy8805]

Thank you 1A Auto for a great video and great parts! Could not have done it without you! DIY Retiree Honolulu

[@1AAuto]

+Dodo Boy Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

[@splitplug]

Is this fix do-able if the window won't go down currently? How would I get to the bolts with the window all the way up?

[@ccisneros2007]

Thank you sir. Works like a charm now. :)

[@brodtstuff]

Great instructional! Appreciate the hard work to make it very useful step by step

[@efrainnieves9959]

Perfect video i do change my motor window with out problem doing exactly like in the video thank you so much.

[@thejool]

Best video out there on how to do it! Amazing! Thank you! Can you come fix my door please!! Lol also my locks aren’t working with main control panel either and a new one didn’t solve the problem either. What is wrong? Anyone know?

[@mikemccaffrey8500]

great video! whom ever replaced my driver front did not set motor travel properly. this will help me! Also need to replace passenger front....motor is tired

[@1AAuto]

+Mike McCaffrey Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com

[@marionavarrete8177]

thanks, very informative. why do u have to rotate the motor 6 - 10 cycles or ( 4 seconds aprox) ?

[@shushlopez9014]

You are good teacher

[@1AAuto]

+Shush López Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

[@whiteshepherd5390]

Great Video. Very easy to follow. I was wondering if you have one for the front passenger door window motor or if the driver side and passenger side are the same procedure? Thanks

[@1AAuto]

+White Shepherd We currently do not have an auto repair video that covers this particular repair. We will keep this request in mind in the event that we need to make this repair in the future. 1aauto.com

[@CharacterZ3r0]

I followed this same procedure for my passenger side door. There is just no auto up & down, the rest of the procedure is the same. Works great!

[@tonymontenegro4686]

GREAT VIDEO ,,, THANKS

[@jbradshaw9321]

My window motor is dead, can I manually lower the window to get to the bolts? 2000 Toyota Rav 4

[@iqbalansari6836]

excellent work man..

[@1AAuto]

+Iqbal Ansari Thanks for checking us out! 1AAuto.com

[@scooter12368]

so you need to lower window to get to those bolts. how would you lower window if the motor is not working?

[@veetacrews2917]

Real good 👌 to watch

[@1AAuto]

+Veeta Crews Thanks for checking us out! 1AAuto.com

[@MadClowdz]

Great video, followed all the steps and replaced the driver's power window motor in my 2001 Highlander with the motor from 1A auto. Only issue is, when I use the auto up, it goes all the way up then halfway down. Everything else works fine, up, down and auto down.I followed the steps to idle and calibrate the motor...connected it to switch and hit the up (not auto up) for 4 seconds, then, once installed went all the way up and down twice...maybe I had it positioned incorrectly on the regulator to begin with..? Is there a way reset and re-calibrate the motor without taking everything apart again?

[@brodtstuff]

Yes there is, I can't find the reference at this time, but there was a note/or video that had the key go on and off and work the switch three times to readjust I cannot give you the exact details, just know that it is out there and possible

[@saudan3110]

can I open 6 bolts hold motor and regulator to lower down the window glass then open 2 bolts at the bottom of the glass, is that ok ?

[@flightcommander3550]

The video is excellent and helped me to remove the window and door panel without issue. I ordered the part but the part sent to me is not correct. The 3 holes on the motor used to attach it to the track do not have any threads in them so I cannot attach the motor to the track to complete the installation. How can I exchange the wrong part for the right part so I can complete this project. Thanks

[@1AAuto]

+Flight Commander Thank you for your order! I recommend you give our customer service department a call and we will be able to look into the issue further. From the sounds of it you may just need to get nuts and bolts to complete the installation. Most aftermarket regulators will not be threaded like OE. www.1aauto.com

[@DavidScott-nw7kw]

thanks for the video, made the job so simple

[@1AAuto]

+David Scott Thank you for your feedback! We are happy we could help.

[@StacyBrown2]

Your video is awesome!!! Thank you much.

[@1AAuto]

+Stacy Brown Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com

[@paulgibby6932]

16:22 so the motor can overheat and not work? Great video, but these wimdows are a real pain - my only problem with my 2005 Highlander. Thanks

[@bowlmeoverva]

Great help in fixing my 2010 Highlander Driver side door. Especially the motor swap out. Thanks!

[@jalaawn3600]

thank you

[@1AAuto]

+Ja Laawn Thanks for checking us out! 1AAuto.com

[@dragonext2001]

What do you do if one of the connector that connects the window glass to the regulator is on the window and the window is out of the door. Oh and the 10mm bolt hole for that 1 part that's still on the glass is broken but the other one that's not broken is still on the track? I ask coz I came home from work yesterday to find wife's passenger window down on her highlander. I told her about it and she informed me the window didn't work. I thought it wouldnt go up or was off the track. Found her window in the driver seat with 1 of the regulator connectors still on the glass but broken where the bolt goes. Took the door cover off to find the track broken and the other window to regulator connector still on the track.🤷🏻‍♂️

[@lennytocco7664]

i did all that and my window goes up and then when it reaches the top it reverses and comes down about 6 inches and stays open???? tried programming, aggravated need help?

[@unexpected2792]

Where can i get a motor for the rear left, i have only seen the passenger right and rear right as well as the drivers side (this one) but i cant find the rear left.

[@saudan3110]

The motor was dead at up position, how to lower down to loose 2 bolts connected with the class ?

[@1AAuto]

+Sau Dan Thanks for watching! If you can gain access, you can open up the motor and manually crank it.

[@victorpelayo9666]

@@1AAuto what if you can't gain access

[@ComplicatedMelodee]

That was a great video. I totally feel like I could do this myself. :)

[@1AAuto]

Thanks for checking us out. 1aauto.com

[@SteveLord]

How about if the driver window is stuck down and the motor flat out doesn’t work?

[@KerKoy]

Same part for the rear driver side(LH) as well?

[@louisianaguy2661]

That is a different part. Look on the Dorman web site. They offer replacement parts and they show the part and different part numbers.

[@Homestar1217]

What was the reason for the motor replacement? I have a 2003 and the driver's side window just stopped rolling down at all. Trying to figure out if it is the master switch or the motor.

[@MadClowdz]

Depends. Was it slowing down and stopping before going out altogether? If it's the motor, generally, it will go slow, stop, then go slowly again and then stop...that's what mine did. It would work fine going down, then up it would go slow and then stop, then I wait about 30 seconds, and it starts moving slowly again. Followed this video's instructions and replaced the motor and it works great now. If it just stops suddenly, without warning, it could be the switch.

[@DwayneHicks426]

Overheat???

[@georgegary8621]

2009 Toyota venza window need to be put on track

[@ben-eh3ey]

Where’s the heck is the passenger side window motor replacement

[@OGBOOTSY]

I was Suprised your gloves never got torn..

[@jeffjensen27]

I would like to know in my mind in theory my own personal design concept should work using the existing design and concept of using a regular automotive window switch with the master switch and instead of rolling up and down windows I would utilize All 4 motors as small winch’s. The 4 separate motors would each have their shaft extended and the opposite end of the new shaft would be in a free spinning enclosed bearings each motor would control 1 single 10’ 1”3’/4 diameter EMT conduit which it’s self isn’t that heavy. What is going to be hung from theses various pipes will be assorted very light weight valances, led lights, all light weight. So if wired correct in theory I would be able to have full control of 4 separate individual pipes or turn on the master switch and all 4 pipes would work together up and down.🤔✍️✍️✍️✍️✍️🤔🤔🤔🤔✍️✍️✍️🧐🤞🤞😲👍🏼✅🙏Correct?