2.94g, Supermicro RC Plane 만들기 (3Channel)

[@Jucuco]

WOW! Never knew about these magnetic actuators. Excellent instructional and informative video!

[@creativechannel9368]

Thank you... Have a nice day...^.^

[@wesleydeer889]

This should have more views, awesome build

[@creativechannel9368]

Thank you...^.^🙂

[@00GOKU10]

Maybe u should use 720 motor

[@creativechannel9368]

I think it's too heavy... will it be ok?...^.^

[@00GOKU10]

@@creativechannel9368 Bro are you on insta cuz i want to show something

[@00GOKU10]

@@creativechannel9368 I made a plane like u but i don't have motor but I have small battery 😂

[@xtofduurr]

It's relaxing and tense at the same time to watch and I guess to build as well. Bravo.

[@creativechannel9368]

Thanks Bro...^.^

[@monumonu-fc5jc]

any micro rc receiver connect rc transmitter ??????

[@creativechannel9368]

It's not like that. Each receiver and transmitter must use products with compatible protocols. Most products (transmitters & receivers) produced by the same company are compatible with each other...^.^

[@Sock_real]

This video is super helpful :)

[@creativechannel9368]

@@Sock_real Thanks...^-^

[@toyschannel4869]

Where did you buy receiver

[@creativechannel9368]

Information is provided in the comments section at the bottom of the video above...^.^ * 2.4Ghz Transmitter & Micro 4ch receiver & Micro actuator & 1Cell battery... and so on... www.Drcmall.com www.MinimumRC.com

[@sierrason830]

대단하십니다.

[@creativechannel9368]

감사합니다...^-^

[@MarkJimenez-dw1tl]

What time of reaceacer did you use that's can bind on the fly sky?

[@creativechannel9368]

I don't understand what you're asking. What does 'reaceacer' mean?

[@MarkJimenez-dw1tl]

@@creativechannel9368 micro reaceaver the board that I can bind whith fly sky fsi6 transmitter for ultra micro planes

[@creativechannel9368]

@@MarkJimenez-dw1tl Oh... I understand now. Are you talking about Receiver (2.4Ghz Super micro 4ch receiver)? The above transmitter and receiver were purchased from a Korean RC shop. I am not sure if it is possible to bind it with your original FLYSKY transmitter. I think a safe binding will only be guaranteed if you purchase the transmitter and receiver from the same place...^.^

[@jamesjun5515]

Can you give me an exact US link where to buy the actuator at did you make it

[@creativechannel9368]

Hi, brother... for your questions, please refer as follows...^.^ * 2.4Ghz Transmitter & Micro 4ch receiver & Micro actuator & 1Cell battery... and so on... www.Drcmall.com www.MinimumRC.com

[@ayaanbopaiah9441]

Hey can you please tell me what the receiver is called?

[@creativechannel9368]

For your question, please refer as follows...^.^ * 2.4Ghz Transmitter & Micro 4ch receiver & Micro actuator & 1Cell battery... and so on... www.Drcmall.com www.MinimumRC.com

[@TheCubbyman61]

Try gearing your motor so you can use a bigger prop. Your target weight should not at least exceed 3.8 grams and that will fly. I made a tiny Spitfire years ago weighing 3.8 grams out of durobatics foam and Plantraco 2 ch system with a 30 mah lipo battery, a 4 mm pager tail motor from an IR toy helicopter. Yours will fly.

[@creativechannel9368]

In the first place, the goal was to make less than 3g, so the gear system was not considered. But, I will try again soon... Thanks for your advise...^-^

[@philfrydman2576]

Impressive really ! Congrats. You could have saved more by direct board soldering saving on 6 connectors/6 soldering points + 2 connectors for Lipo bat + simple wires and 2 soldering points for lipo. 0.2 to 0.4g to my calculations.

[@creativechannel9368]

Thanks for the advice. Have a nice day today...^.^

[@thefreedom9973]

not good.. what do you need? answer: big wings

[@creativechannel9368]

Thanks for your opinion...^-^

[@우주라마9년전]

미니rc비행기만들때 팁좀요 ㅠㅠ

[@creativechannel9368]

미니 RC 제작시 가장 중요한 점 이라면, '비행중량의 감량' 이 아닌가 싶습니다. 기본 기자재들 구입시 각 부품의 '무게'를 철저하게 확인을 하셔야 합니다. 그 다음으로는 '무게중심(CG)' 가 될듯 하네요. 큰 기체에 비해서, 기자재들을 배치할수 있는 위치가 제한적이다보니 많은 고민이 필요합니다...^-^

[@우주라마9년전]

@@creativechannel9368 감사합니다

[@ornithopterindia]

👍

[@creativechannel9368]

Thank you...^.^

[@daviddavids2884]

some late information. that motor may not be powerful, enough. however, there are some OTHER things to contemplate. the shapes of wing and stabs sucks. on a model this size, the use of outboard dihedral results reduced efficiency and roll-axis stability. the area of control surface areas are Small, with NO associated reduction in Mass. because the wing has a zero-lift profile, ALL lift must come from positive aoa. angle of attack. i have details, if you want them. cheers googletranslate

[@creativechannel9368]

Thanks for your help. It will help me a lot in the future. I'll try a little more... Have a good day...^.^

[@philfrydman2576]

Agreed. 0 lift wings compensated by aoa so more drag. Is it possible to shape the wings profile with hot air blower ? Making a positive lift with small drag.

[@ripungogoi2888]

Motor does not high rpm

[@creativechannel9368]

Yes... it could be... Thanks...^.^

[@张远-b9o]

怎么没飞起来，动力不足么……

[@creativechannel9368]

Yes... I thought that if I had made the wing area of the wings a little bigger, I would have been able to fly better...^.^

[@odalistejada5136]

Con una ala con perfil curvo te resulta mejor

[@creativechannel9368]

Oh, I see... Thanks for the advice...^.^

[@Esoocelik]

👏👏👏

[@creativechannel9368]

Thanks bro...^-^

[@davidsetiawan9405]

.