200 TDi Injector Cleaning.

[@colinaglae9753]

Super video, Fluffle. Extremely educational diesel injector cleaning video !!

[@FluffleValveExpress]

Thank you.

[@albertoromano7853]

Ciao, complimenti hai fatto un bel lavoro e un bel video.

[@FluffleValveExpress]

Thank You.

[@piecetoyou8285]

Nice work thank you, A little tip for you, when placing litlle washers down any tube` if you get a long wooden skua place that down into the injector` and then place washer over skua ` the washer will drop down without flipping then just remove skua,

[@johnkerr8019]

I've watched quite a few of these injector cleaning videos and this has been the best so far, very comprehensive and great to witness the end result. Good JOB!!

[@FluffleValveExpress]

Thanks ...

[@gerryrichards2863]

Thanks mate. I have my injectors out on my 98 Land Rover Discovery 300 TDI and will follow your instructions to clean them up and see how it runs. We are in Winter here (Australia) and I hope the cleaning will make it run a lot smoother for the Summer months when I use it the most. It runs quite rough at the moment. Great instructions mate. Thank you - Gerry

[@FluffleValveExpress]

How did it go with the clean up?

[@jamesferguson1140]

Great info. Thank you. I will have a go at my marine engines now after your teaching. Thanks again.

[@davidwall6020]

great video ...makes me confident to try it myself, Thank you

[@di4241]

Very educational, thanks for making this video.

[@charlescopp3432]

Thanks from up state NY 🙂

[@FluffleValveExpress]

Thank you 😊

[@IQ0100]

Cheers mate. Will have a go with my Pug 407 2.0 hdi injectors. Ys jazz

[@jameslatimer1432]

Great job bro got to do my m57 ENGINE BMW 3.0td x6 same job

[@johncraig6986]

excellent strip and reassembly, and advice; really useful.

[@markrayton6385]

Excellent video. Thanks for sharing. Only problem I have is I don't have access to an airline.

[@FluffleValveExpress]

That'll be the next thing on your shopping list. An Air-Line is a godsend in any workshop.

[@johnswimcat]

Great video. I would wear nitrile gloves though and would use copper wire to unclog the nozzle holes... unless I was desperate..!! I wouldn't use a sewing needle though unless I was completely desperate... as anyone who works on their own vehicles will sometimes be!

[@TheBert1948]

thanks for the video, helped me cleqn the injectors on my car, saved £480,

[@FluffleValveExpress]

What car is it?

[@charlescopp3432]

Thanks 😊 great tutorial!

[@Red_Vector]

Thanks for the video very helpful and easy to follow

[@jasonga]

What do you put on them to aid removal in the future?? Please…

[@FluffleValveExpress]

Copper slip on the threads.

[@jasonga]

@@FluffleValveExpress YES, I knew it, I been doing that and work mates cocking nose up…. I use the copper slip and really rub it in……. Thanks, good video…..

[@jeffmee763]

Hi Isi it a a bosch injector thanks good video.

[@FluffleValveExpress]

I do believe it is a Bosch Fuel injector.

[@DavySwift]

Nice one 👍 Thanks for sharing.

[@peterbloggs8750]

Excellent video but why not anneal the copper washers before you put them back under the injectors?

[@FluffleValveExpress]

This something people don't know. I have in the past annealed copper washers on sump plugs. I suppose it depends on "If it leaks" or not. Sometimes it's just as well the buy new.

[@javerlozep162]

Great video never seen

[@FluffleValveExpress]

Glad you enjoyed it

[@MarktheOddJob]

Nice video Frenchie, never knew you were so famous!

[@mauricioericfalcon9546]

Lo intentaré 👍🏼

[@RoyaJoha]

I did the work!.. deleted code and yay!.. Except 8 sec later code is back and now it’s leaking at new areas.. any torque spec on the items (all pref) for a Ford transit connect? 😅

[@FluffleValveExpress]

Sorry, I know nothing about the Ford Transit other than that I owned one in the late 1980's It was a MK2 Mini bus, converted to a camper.

[@RoyaJoha]

@@FluffleValveExpress ah that’s all good 😊 thank you for the video though! I’ll get there in the end I’m sure.. orrrr a new injector is already in the mail..😅

[@ribama1]

This is a great video but you need to know what type of injector you have. If you have a piezoelectric injector it is hydraulic no springs and tolerances of 3/1000th you can't clean like this.

[@stanislas2008]

Fucking master .. you're a great help.. thank you so much for your expertise and patience to do this awesome videos...

[@eyeswideshut7732]

time stamp 30.22 lol what happened to cranking for 20 mins.... if only they were all like that...

[@TheYesnoyesnoyesno]

Very useful - thanks!

[@AnasKhan-vz6gn]

Thank

[@nazmibullari6469]

Bravo

[@ciaranoconnor6783]

Hi' I have just had an engine fitted on my 313 sprinter. Mechanic has fitted new delphi injectors but wont start. Delphi say injectors have been scarred and are now knackered (won't replace them) have you or your followers experienced this , what could be the cause and do you know of a solution

[@FluffleValveExpress]

Could be the mechanic has damaged them somehow? If you damage the Nozzle/Tip of the injector, it won't spray correctly.

[@xXJusTMichelxX]

I took an injector off to clean it and now the car is not starting, all the injectors are not spraying, there is pressure in the rail but the injectors are not opening. Help me please

[@FluffleValveExpress]

Try bleeding the system. Crack open the feed pipe to the injector while cranking the engine over. Are you sure everything went back together correctly 🤔.?

[@xXJusTMichelxX]

@@FluffleValveExpress Was air in the rail, I did what you said and it starting now . I can't thank you enough. Have a great life. Can I give you £10?

[@FluffleValveExpress]

@@xXJusTMichelxX I'm just glad that you are sorted 👍 😊 Keep your moneys for fuel ⛽

[@xXJusTMichelxX]

@@FluffleValveExpress Thank you again, sorry didn't mean to be rude about the money, If you were here I would probably take you out for a beer :))) ! Have a nice day!

[@BillSikes.]

I tried this with my mondeo tdci injectors and its never run since, I don't think they're opening, it won't fire at all

[@FluffleValveExpress]

Hopefully, you have put them back together in the correct order that they came apart? Also, did you bleed and prime the diesel system before trying to start the engine?

[@BillSikes.]

@@FluffleValveExpress Thanks for the reply, yeah it's all bled up, and there's pressure there, coz I get a big squirt when I crack the nut on the inlet pipes, but il dismantle them again tomorrow to see if I didn't put them back right, cheers il let you know

[@TVTika]

@@BillSikes. what news ?

[@BillSikes.]

@@TVTika It never ran again, I scrapped it in the end

[@habibizhafranzhafran8343]

May Allah give you hidayah....aamiin

[@Stainless316L]

brake cleaner/tattoo remover lol 😆

[@frankydbladebod2777]

Should be wearing gloves, should not be firing compressed air into palm of hand either

[@FluffleValveExpress]

Very True, but we have all been there and done it. I do wear gloves on some jobs, but it's the fiddly jobs that gloves can hinder.

[@volvovolvo8733]

motor 1.9 tdi mozzle

[@FluffleValveExpress]

Land Rover, 200 and 300 Tdi injectors.