Diesel Injector Leak Off Test and Nozzle Clean DIY (Bosch Injectors for BMW M47 M57 engines)

How easy is it to check your BMW Bosch diesel injectors for good operation using a leak-off test and then clean the nozzles? Will ultrasonic cleaning work? Will high pressure washing work? What are the tricks to easy injector removal? How do we see the spray pattern to verify that it is good? How do we know if the needle valve is end-of-life? How do we make sure that our injectors don't leak after we install them? Watch and find out! This video applies to many diesel cars made between 2000 and 2007 that use Bosch electro-mechanical injectors, and applies specifically to BMW M47, M57 and M67 diesel engines from 2000 to 2007 (or so). This video does not apply to mechanical injectors or piezo-electric injectors (although there are many similarities).
Subscribe! / @stevenbtuner
#BMW #BMWDIY #BoschCarService
Here is a breakdown of the chapters in this video:
00:00 Intro
00:38 Corrected subtitles are now available for all Steven B Tuner videos
01:02 Vehicle Preparation
01:47 Get to the Injectors
02:31 Remove Injector Connections
03:55 Connect Test Equipment
05:41 Run Leak Off Test
07:13 Are the Injectors Good?
07:46 Removal Tips
10:02 Disassemble Injectors
13:36 Inspect Dirty Nozzle
14:09 Ultrasonic Clean the Nozzles
15:06 Inspect the Ultrasonic Cleaned Nozzle
15:44 Pressure Washer Clean the Nozzles
16:34 Re-assemble the Injectors
19:01 Injector Installation Tips, Reaming and Cleaning
20:56 Febi Bilstein Special High Temperature Ceramic Grease
****** Amazon.co.uk Links for United Kingdom Viewers******
Products seen, used or mentioned in this video are available on Amazon via the following paid links: As an Amazon Associate, I earn from qualifying purchases.
- 30 liter Ultrasonic Cleaner: amzn.to/2NoBxGY
- 10 liter Ultrasonic Cleaner: amzn.to/3sVi1Cu
- 3 liter Ultrasonic Cleaner: amzn.to/3sLwVee
- Carburettor Cleaning Solution: amzn.to/2LXoZG8
- 5pc Diesel Injector Reamer Kit: amzn.to/3c5SgJr
- Diesel Injector Removal Kit: amzn.to/3ocSot2
- Diesel Injector Leak-Off Test Kit: amzn.to/3qJjz0n
- Pick-up Tool: amzn.to/365s4Lq
- Flare Nut Wrench Set (inc. 15mm): amzn.to/39Z090H
****** Amazon.com Links for United States / Worldwide Viewers******
- Ultrasonic cleaner: amzn.to/36SovH9
- Diesel Injector Reamer Kit: amzn.to/2sIyDTc
- Diesel Injector Removal Kit: amzn.to/2s3gO12
- Diesel Injector Leak-Off Test Kit: amzn.to/2Q7SSla
- Pick-up Tool: amzn.to/2EykMS2
- Flare Nut Wrench Set: amzn.to/34AZQEt
Music used in this video:
---
Replicant World by Mike Chino
/ mike-chino
Creative Commons - Attribution-ShareAlike 3.0 Unported - CC BY-SA 3.0 creativecommons.org/licenses/b...
Music promoted by Audio Library • Replicant World - Mike...
---
Ason ID - Xander by Ason ID / ason-music
Creative Commons - Attribution 3.0 Unported- CC BY 3.0 creativecommons.org/licenses/b...
Music promoted by Audio Library • Xander - Ason ID (No C...
---
Skydive by Loxbeats / loxbeats
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/2uUKEmd
Music promoted by Audio Library • Skydive - Loxbeats (No...
---
Electric Joy Ride - Origin [NCS Release] • Electric Joy Ride - Or... / electricjoyride
/ electricjoyride
/ electricj. .
Music promoted by Audio Library • Origin [NCS Release] -...
---
Funky Souls by Amarià / amariamusique
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/Funky-Souls
Music promoted by Audio Library • Funky Souls - Amarià (...
---
Lensko - Circles [NCS Release]
• Lensko - Circles | Hou... / lensko / lenskoofficial / lenskoof. .
Music promoted by Audio Library
• Circles [NCS Release] ...
---
Beach Buggy Ride by SIRPRICE / sirpricedj
Creative Commons - Attribution 3.0 Unported- CC BY 3.0 creativecommons.org/licenses/b...
Music promoted by Audio Library • Beach Buggy Ride - Ele...
---

[@michaellavery4899]

Thanks for another great video, Stephen. This guy makes the best instructional videos of this type on KZbin. I would like to thank him for the time and patience he has extended to me.

[@StevenBTuner]

:-) :-)

[@zeesee3918]

Thanks Steven, I found your videos amazing - it gives a little confidence to do it yourself. Bless you.

[@StevenBTuner]

I'm glad they help you out!

[@JonCianci12]

That was really kind of you to make this video. Thanks!

[@StevenBTuner]

I hope it helps you out!

[@BrainXTV]

Great video. Easy to understand and many tips for people who doing this the first time. Great job. Thank you.

[@StevenBTuner]

Welcome!

[@koetjepeterprahs9263]

This is just my cup of tea.

[@michaeltietzyou]

this is almost the best video I have seen to this theme - thank you. Very helpful also for an Merc W163 270 cdi

[@StevenBTuner]

I'm glad to hear that it helps you out!

[@briangibbon8711]

An outstanding video Steven. Thank you for sharing the benefit of your hard earned experience in meticulous detail.

[@StevenBTuner]

Welcome!

[@henriryonankoski]

Just found your channel. Really great videos. You are an true educator!

[@StevenBTuner]

Welcome! :-)

[@Andy_83_SWE]

Really glad i found your channel. Thx for great help!! Keep it up

[@StevenBTuner]

Welcome to the channel! :-) It's really good to hear that it is helping you out!

[@christianb4994]

Super!! 👍👍 Vielen Dank aus Deutschland. Eine wirklich gute Anleitung. Top!

[@tokenfire111]

Great video Steven. Well explained and easy to watch / listen to.

[@StevenBTuner]

Thanks!

[@ezequielcosta954]

Great video!!One of the best I have seen!!Thanks man!Keep up!!

[@StevenBTuner]

I'm glad you like it!

[@joeyjones6638]

Excellent video once again mate I wish my teachers at school could of explained things as good as you do and I may have learned a lot more. Great chanel thankyou.

[@StevenBTuner]

I'm glad you liked it! :-)

[@kirwanjohn101]

Thank you for your help in making this video. I removed my 4 bosh injectors from my opel corsa diesel and cleaned the nozzles using an ultrasonic cleaner like you did. The car is running much smoother now. The acceleration is very smooth. My car has 290k km. Thanks again

[@StevenBTuner]

Great job!

[@Flatwaterkayakpm]

@@StevenBTuner Hello, i have a n57 engine with 105k miles, it runs perfect no rough idling, no smoke nothing runs like new, but there is only one and only one issue, when i take the engine cover off i can see wetness around 3 out of my 6 injectors. Does this indicate bad seal o rings(copper ones)or is it something more serious ? Thank you in advance your answer would help me a lot !!

[@kirwanjohn101]

@@Flatwaterkayakpm yes, you have a small leak around the injectors. You will need to remove them and replace all copper washers. First I would recommend cleaning the area and observe it for a week just to make sure that it is not a spillage of oil before you start.

[@StevenBTuner]

Who is ready to check their diesel fuel injectors for good operation, and then give them a nozzle clean? This is the new version of this video, and I’ve included some great extras that were suggested to me by you guys! If you do the leak-off test, and you find that the amount of diesel in each vial is vastly different, or if the amounts are a lot different to what you see in the video - then you should remove your injector/s and send them off for a professional rebuild using genuine Bosch parts, and a re-calibration (you will need to re-code your injectors after). If the leak-off test shows that there are no issues with the injector's high pressure ball valve then you may want to go on to clean the injector nozzles, to make sure that no blocked holes are causing a bad spray pattern. Your engine will continue to run reasonably ok with one, two, or even three blocked nozzle holes, but the resulting bad spray pattern will eventually cause wear on your engine's cylinder walls. It is the slow death of your engine. By doing this service every 100,000 miles, you can help your engine last much longer! Here is a breakdown of the chapters in this video: 0:38 Corrected Subtitles are now available for all Steven B Tuner videos 1:02 BMW Bosch Diesel Injector Servicing - Vehicle Preparation 1:47 BMW Bosch Diesel Injector Servicing Leak-off Test - Get to the Injectors 2:31 BMW Bosch Diesel Injector Servicing Leak-off Test - Remove Injector Connections 3:55 BMW Bosch Diesel Injector Servicing Leak-off Test - Connect Test Equipment 5:41 BMW Bosch Diesel Injector Servicing Leak-off Test - Run Leak Off Test 7:13 BMW Bosch Diesel Injector Servicing Leak-off Test - Are the Injectors Good? 7:46 BMW Bosch Diesel Injector Removal Tips 10:02 BMW Bosch Diesel Injector Nozzle Cleaning - Disassemble Injectors 13:36 BMW Bosch Diesel Injector Nozzle Cleaning - Inspect Dirty Nozzle 14:09 BMW Bosch Diesel Injector Nozzle Cleaning - Ultrasonic Clean the Nozzles 15:06 BMW Bosch Diesel Injector Nozzle Cleaning - Inspect the Ultrasonic Cleaned Nozzle 15:44 BMW Bosch Diesel Injector Nozzle Cleaning - Pressure Washer Clean the Nozzles 16:34 BMW Bosch Diesel Injector Nozzle Cleaning - Re-assemble the Injectors 19:01 BMW Bosch Diesel Injector Nozzle Cleaning - Injector Installation Tips, Reaming and Cleaning 20:56 BMW Bosch Diesel Injector Nozzle Cleaning - Febi Bilstein Special High Temperature Ceramic Grease

[@leonsletterbox2013]

Hello again Steven . Picture says 1000 words. During this video @ 10:20 , with your left hand you touch the injector, this is the part of the injector I mean when I say sleeve/shaft with the O-Ring on it too, this shaft can slide up and down(no side to side movement) 10-15mm on 2 of my injectors but other 2 soild. Any help appreciated thanks from Leon.

[@ay7pre]

thank you for the time you take to put all this details in here, it really makes a difference

[@StevenBTuner]

@@ay7pre You're most welcome!

[@ay7pre]

I wanted to know, after you clean the injectors, do you have to code them so that the engine will start again? or it just starts and runs as before?

[@StevenBTuner]

@@ay7pre Hi, the nozzle cleaning has just brought the injectors back to how they were when they were calibrated, so there is no coding as long as you put them back in the same cylinder, and keep the parts for each injector together throughout the whole process.

[@Crypt1c]

You made that look easy! Well done sir.

[@StevenBTuner]

Thanks 👍

[@sparkyhobo3844]

Excellent detailed procedure with easy to follow narrative. A++++

[@StevenBTuner]

Glad you enjoyed it!

[@peterclune4770]

Very good demonstration Steven well done

[@StevenBTuner]

:-)

[@timlewis8231]

Excellent! A clear articulate explanation.

[@StevenBTuner]

Welcome!

[@MePeterNicholls]

This has given me confidence to try this myself.

[@StevenBTuner]

I hope you'll report back how it all goes!

[@mikeslater1865]

Hi, your videos are well presented and easy to follow and understand. They encourage DIY mechanics like me to have a go at doing our own refurbs and repairs, etc, and also save ££££’s. Thank you!

[@StevenBTuner]

Glad to help!

[@the_punisher01]

Wow! After watching this video now I want to refurbish my injectors too. Wish i own an ultrasound cleaner. I know that device make miraculous cleaning. Thanks for the good tips

[@StevenBTuner]

:-) They will all need doing eventually! I'm glad you liked the tips.

[@theEskalaator]

It's not a miracle, but it works quite well. You also need good chemicals for good cleaning.

[@602jon]

As many others have already mentioned these are great videos, well done. Cleaned my N47 BMW DPF after viewing a few of your videos and great results. I did used a pressure washer as well which appears to get some extra ash out. Checked DPF with camera after and no damage. Now very low back pressure and performance restored to like new. Many thanks.

[@StevenBTuner]

Thanks, and great to hear that your DIY DPF clean worked well!

[@nevinhattle1914]

the DPF video was gold

[@jlewy2140]

thanks for so much detailed video !

[@StevenBTuner]

You're welcome!

[@focusmicro]

I have to replace my cylinder head cover gasket tomorrow (B47 engine), and came across this video ( thank you) to clean the injectors too!

[@StevenBTuner]

You are most welcome, and all the best with the job!

[@musabasete982]

I very much enjoyed your video, one of the best & I was totally glued all through the process, can't wait to see the next video. ❤❤❤😊

[@StevenBTuner]

Glad you liked it!

[@user-fu6qu1hd5l]

Good job. Really helpful video. Tnx Steven

[@StevenBTuner]

Hi, glad you like it!

[@raviragbir6920]

Wow, one of the best I've seen

[@StevenBTuner]

Glad you got something out of it!

[@kianward5999]

that was a stunning vid pal what great content

[@StevenBTuner]

Thanks!

[@koetjepeterprahs9263]

Sir, You are a car hero!

[@StevenBTuner]

:-) Thank you for watching!

[@greglevi1633]

Thanks a lot. Keep up what you doing.

[@StevenBTuner]

Thanks, will do!

[@gidmosia7065]

You are a Legend Steve Thanks once more

[@StevenBTuner]

Thanks!

[@lassesebarbar]

Thank You Steven i report back to You of my progress with my Skoda Superb 2011

[@StevenBTuner]

All the best with the job!

[@kirwanjohn101]

I must compliment you on an excellent video and clear instructions. Just did this today on my opel corsa 1.3l diesel and all is well. Thank you.

[@StevenBTuner]

Awesome to hear! Those Corsa injectors are almost identical to the BMW injectors in the vid. Well done on a DIY success!

[@SalimKhan-gk1fh]

Did it run smoother John??

[@StevenBTuner]

@@SalimKhan-gk1fh Hi, the most noticeable difference is usually quicker starting.

[@kirwanjohn101]

@@SalimKhan-gk1fh yes, acceleration is much smoother. Car engine is also quiter. My car has 290k km.

[@ryanh3285]

Lots of knowledge shared there good video.

[@StevenBTuner]

Thanks 👍

[@longhuynh5249]

Amazing video, loved it.

[@StevenBTuner]

Glad you enjoyed it!

[@stephenkelly5642]

A very clear informative video. 👌

[@StevenBTuner]

:-)

[@OctavChelaru]

Brilliant bideo man, thanks for sharing!

[@StevenBTuner]

Glad you enjoyed it!

[@marcellemeyer2380]

An easy test you can do if u experience hard starting is to just simply remove the connectors and return line from the injectors and crank the engine, there should be NO leakage coming from the injectors, any diesel leaking from an injector doing this test is a bad injector and needs to be checked. Great vid :D Edit: this test is obviously only viable if the high pressure pump and rail is generating pressure to the injectors

[@benjietan6475]

Tnx watching your videos from baguio city philippines

[@StevenBTuner]

Thanks for watching! :-)

[@magicmax6973]

best assembly video, thank u very much

[@StevenBTuner]

You are most welcome!

[@nevinhattle1914]

Best mechanic on youtube hands down

[@StevenBTuner]

Thanks!

[@nevinhattle1914]

@@StevenBTuner your more than welcome, when ever I need in depth proper tutorial video's, this is where i come, I have learnt a great deal of information from you, so thank you for your time and effort i am a huge fan

[@chrissein632]

Great Video! Very helpful

[@StevenBTuner]

Glad you liked it!

[@kirwanjohn101]

Very clear instructions

[@StevenBTuner]

I'm glad the vid helped you out!

[@mpgalhenage]

Thank you very useful 😊

[@stuart1030]

Absolutely brilliant video, . You have tought me so much and i have enjoyed every single second of it. Thank you, thumbs up and subscribed. ****************

[@StevenBTuner]

:-) :-)

[@yunuscoban4899]

Nice video, thanks man.

[@StevenBTuner]

Glad you liked it!

[@asimturkiye1453]

Tesekkur ederim Steven , ellerine saglik , guzel bir calisma olmus

[@StevenBTuner]

Rica ederim!

[@asimturkiye1453]

@@StevenBTuner je vais acheter la meme machine ultrason que toi est-ce une 40w ou 100w ? Faut il acheter son liquide aussi ? Enfin dois je reprogrammer mes injecteurs ? Merci d'avance

[@stuungar3390]

Very therapeutic tutorial

[@StevenBTuner]

Therapy for the injectors too :-)

[@stuungar3390]

@@StevenBTuner - lol, everyone's happy

[@thegrimreaper8843]

Good video as always Steven! :-)

[@StevenBTuner]

Glad you enjoyed it!

[@zaida500]

You need this!!!

[@NinpoUK]

Bookmarked this after I got a 004B10 code, the glow plug controller had been faulty before so I'm guessing it's had a knock on effect to one or more injectors. I now know how to run the leak off test, thank you!

[@StevenBTuner]

Hi, they aren't directly related, but if the glow plugs aren't operating then there could certainly be a bit more black soot clogging up the combustion chamber every time you do a cold start, which might end up in the fuel injector tips.

[@seankirby2580]

Steven, you're amazing. I have a 2010 BMW 316d LCI and at least 1 injector is dodgy, putting the yellow "drive slowly" light on. I saw white smoke, smelling of diesel, from the exhaust. I was frightened of the injectors at £1200 ($1600) the set. Not any more, thanks to you. I owe you, mate. Brilliant.

[@StevenBTuner]

Hi, there still might be something terminal with your injectors - but it is good to have the knowledge to check and correct everything you can.

[@seankirby2580]

@@StevenBTuner I've just removed 1 injector (twice). I bought a used replacement for £25 and I'll see how it goes now. I had to remove the replacement because I was too tight to buy a new copper washer. Once annealed, it's OK now. You've been a massive help to me and I'm grateful.

[@StevenBTuner]

@@seankirby2580 Great to hear that it all worked out - well done!

[@seankirby2580]

@@StevenBTuner Update later. I did still have a problem. Fuel starvation on high loads. Bought a leak-off kit and a second hand injector. The test showed the "new" injector (cheap ebay buy) hardly leaked back whereas the old ones filled 30ml in a minute at tickover. Off to ebay for more. So much fuel leaking back that the high pressure rail pressure was low. My old injectors did 137,000 miles / 220,000km. Very grateful for your help.

[@livewildbirdnestcamera]

@@seankirby2580 Hi, sounds like you are on the right track!

[@richardtaylor6322]

Excellent video thanks

[@StevenBTuner]

Glad you enjoyed it!

[@mirkovickovic7059]

Excellent job thank you

[@StevenBTuner]

You're welcome!

[@luizalbertoesposito4010]

Very Nice your explanation!! Best Regards!! Luiz Esposito

[@StevenBTuner]

You are most welcome!

[@mahdi487]

Perfect. Mate! I learnt from you🙏😇🥳🥰❤️

[@StevenBTuner]

Super! :-)

[@THEDIESELCHANNEL]

Great video. Thank you.

[@StevenBTuner]

Thanks for watching!

[@waleedkhalid6021]

So helpfull vedio thank you

[@StevenBTuner]

Most welcome 😊

[@virx15]

Seems a bit more complicated than spark plugs replacement. Thanks for the great video.

[@brendenmoldy]

Nice! THanks!

[@StevenBTuner]

Welcome!

[@asdwee4444]

Hi, Steven! The video was really good! I would like to add some tips from my own experience: 1. After the disassemble of the fuel injectors, I recommend to put them vertically in a jar with concentrated drain cleaner and leave them in the jar for 2 hours but be careful, the level of the drain cleaner needs to not exceed the middle of the injectors (this will help with the opening of the thread and it helps clean the deposit much easier). 2. As the solution that I use in the ultrasonic cleaner device is concentrated drain cleaner and for the rinsing I use isopropyl alcohol. 3. After you assemble the components of the injector, before you thread it, put a small amount of thread blocker (this is going to help with possible future loses of fuel). Keep going with the awesome videos!

[@StevenBTuner]

Hi, thanks for sharing that great information!

[@mihalym.6876]

Hi Lenard, what do you mean "drain cleaner"? Any specific type of it? (Hungarian is OK as well). Thread blocker you mean a thread locker, like Loctite? What exact type do you use? Thank you your answer in advance!

[@asdwee4444]

@@mihalym.6876 Hi Mihaly , drain cleaner = pure liquid sodium or potasium hidroxide . (lugos oldat amit a Lidl lehet kapni,amit a viz lefolyok kidugaszolasahoz hasznalnak.Ami fontos hogy fojekony oldat legyen. Loctite is ok. (A menetett jo egy csep Loctite-al leblokolni, de ha lehet elote zsiroldo szerel letakaritani,peldaul fekrendszer takarito spray-el )

[@AlishanKhwaja]

Good work

[@StevenBTuner]

:-)

[@danilosakovic8243]

Nice video, done this few times... Exact, good, and right procedure. Just one very very important note: Never ever ever never under no circumstance EVER REUSE!!!!!!! copper washer!!!!! Always buy NEW and ORiGINAL washers before this procedure. And don't forget to clean injector hole like shown in this video. Especially bottom part where your Cooper washer sits... Good joob man, liked, subscribed. I am glad you got rid of, mouth sounds from your earlier videos... Good job jebeno mljackanje :)

[@StevenBTuner]

Thanks for watching, and for noticing the improvements!

[@JOSEF7011]

The copper washers must be annealed before installation, otherwise there is a risk of exhaust fumes around the injector. Good job sir!

[@StevenBTuner]

Hi, the washers you get direct from Bosch are ready to use as far as I know, but if you were handling a lot of injector rebuilds then it would definitely be cost effective to buy bulk washers and treat them yourself.

[@anektritrong3026]

Good job.

[@StevenBTuner]

Thanks!

[@orckaso6513]

gr8 information. tnx

[@StevenBTuner]

Most welcome!

[@nateryan7041]

Man that's a great video 👌👌👌 I've learned alot today I've got the BMW m57 engine in my range rover and I think she's got a bad injector or 2 !! At least I have a great know how to guide on how to test them

[@StevenBTuner]

I hope it helps you get your Range Rover back to full health!

[@nateryan7041]

@@StevenBTuner me too I'm not sure if it's a turbo issue or an injector issue or both ?? 😂😂

[@StevenBTuner]

...or as it usually goes: both of those plus a couple of more things!

[@nateryan7041]

@@StevenBTuner I'm Gona check the EGR valve aswell but I'm Gona do away with it to be honest !! Is there anything else you would recommend checking ??

[@StevenBTuner]

Hi, a full health check would start with error codes and then move on to a quick check of everything from the turbo (shaft movement/excess oil) to the intercooler (leaking hoses), and if you are removing the EGR then it could be the right time to make sure that the intake manifold starts of nice and clean, so that it can stay that way going forward.

[@brentsmith5647]

Brilliant video thank u 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

[@StevenBTuner]

You are most welcome!

[@automotiverepairviet8733]

Thank for your video

[@StevenBTuner]

You are welcome!

[@julesviolin]

Excellent work. I tried using injector cleaner directly on the nozzles but it is not effective. The only way is your dismantling method 👍👍

[@StevenBTuner]

They are stubborn little carbon deposits for sure!

[@fiksefant]

Thanks alot for a easily understandable DIY video about these injectors. I've some Bosch injectors for a PSA DV6 engine, I belive they are pretty identical, who need a cleanup after 16 years and 292.000KM :-)

[@StevenBTuner]

Hi, at those kms there is guaranteed to be a few blocked holes!

[@fiksefant]

@@StevenBTuner Hehe, yes I guess you're right. Still I've used some diesel booster last couple of years, so it runs pretty clean. I just did the job with new copper gaskets and sealings on this car. Unfortunately the ones who did this job before me has done a left-hand job, so I had quite some struggles to do it properly. Now one injector are not working properly at low rpm / low load, ok at load, so I'll do the cleanup on all 4 and see if it helps..

[@fiksefant]

@@StevenBTuner Feedback: All 4 had perfect spread. Surprise! No blocking, not even a slight hint of anything but a nice spray! I guess that diesel-booster I always use is doing the job. These injectors have been sat for at least 150.000KMs since a local Ford garage had the job with cleaning and replacing the copper shims... I'm quite sure they did not do anything but that job, no cleaning like you showed in video here. But... One of the injectors has been beaten quite alot, both by Ford garage (who gave up extracting that one) and now me when I after hours with heat, solvents and force finally managed to pull it out. I also found broken treads in one of the clamp bolts for that specific injector, so now Im starting the fun job with Time-Sert and see if that works fine. Hmm... Another reason never leave the job to "proffesionals", hehe.

[@StevenBTuner]

@@fiksefant All the best with the job!

[@godwor848]

The injector is tightened with a torque wrench to 50 LB and you can put a thread lock . Just a bit ... Great job !

[@StevenBTuner]

Great information!

[@jonphillips5119]

Good info as normal

[@StevenBTuner]

Hi, thanks for watching and glad you think so!

[@AndrewBrowner]

good stuff just pulled mine i have about 6mm of carbon on the tips.. might be why it was smoking (12v cummins ppump mechanical injectors) , you must moonlight as a radio DJ with that voice hahah

[@StevenBTuner]

Hi, good work! It could be a good idea to check the rest of the intake system for nasty buildups too.

[@patrickmaritano3802]

Thank you very much

[@StevenBTuner]

You're welcome!

[@jrodri14ii]

Thanks!

[@StevenBTuner]

You are most welcome!

[@davidelliott5843]

The sleeve nut on the bottom of the engine can be EXTREMELY tight. I used an 15mm AF deep six-point socket and 600mm breaker bar. The extra length gives better control but it was glad of it.

[@StevenBTuner]

Certainly is!

[@MrQisar]

Thanks Steven

[@StevenBTuner]

You're welcome!

[@emilioguitart3754]

Wow what a perfectly detailed job !!! Do you need to recode it? They definitely going to spray more than before...or at least clear adaptations?

[@StevenBTuner]

Hi, thanks for watching, and glad you appreciate the detail :-) There is no need to re-code as this job takes the injectors back to match the calibration that is written on them. If the top end is disassembled then they will need to be re-calibrated. Clearing any fuel trim adaptations isn't a bad idea though.

[@philbertnestory670]

I like your professional

[@StevenBTuner]

:-)

[@jaybrown1873]

I like it and I like it alot 😍😍😍😍

[@StevenBTuner]

Thanks for watching! :-)

[@geppiemockingbird1489]

Thank you! Very instructive. But I don't think I will be refurbishing my injectors myself.

[@StevenBTuner]

I understand, it's not for everyone...

[@albiondream]

Nice vid, bud! I was wondering what brand of carburettor cleaner u used as reviews on sum I’ve seen have been questionable.

[@StevenBTuner]

Thanks! For the vid I used "Carburettor Ultrasonic Cleaning Solution" from Allendale-Ultrasonics.co.uk mixed 1:10 with water.

[@cristiana3355]

It will be similar operation on a mk7 golf? Great video.

[@StevenBTuner]

Hi, you will have to look up the part numbers for your car to see if the injectors are of a similar type.

[@barry6873]

cool steven thank you

[@StevenBTuner]

Welcome!

[@pro-powerflushing]

@@StevenBTuner yea it’s a great video I’ve put one new injector in mine focus1.6dtci after it showing uo a daily code and going into limp mode - but it’s still not runing as it shoud so I’ve ordered a leak down kit n de what it says results - I’m gona clean all the injectors anywsy n see if it makes a difference I got an ultrasonic Bath also definetly worth a try 👍

[@StevenBTuner]

@@pro-powerflushing Be great to hear how it goes!

[@barry6873]

@@StevenBTuner ile let you know when i done it :}

[@Tony-wd4uf]

best video,thank you,the ultrasonic in video is 3-10-30L?

[@StevenBTuner]

Hi, in the vid it is a 10.

[@cesarjorgemurillobarientos1813]

exellent

[@StevenBTuner]

Hi, thanks for watching!

[@rudigerkolossa1582]

cool and nice

[@StevenBTuner]

Thanks!

[@leonsletterbox2013]

Hi just noticed, the part of the injector with the o-ring, is this shaft/ sleeve suppose to move/slide 10-15mm up or down thanks much appreciate

[@trashtrash4417]

Hi Steven, awesome video! You encouraged me to give my injectors a nice cleaning too after 320.000km and some beginning „smoke issues“ But before: how was the result of your work? All injectors still running?

[@StevenBTuner]

Hi, it is now coming up to 100,000 kms since I did that job - so I probably should do another leak off test to make sure everything is still good.

[@madmikemakes3056]

Hi Steven. Thanks for a great video. My Opel Vivaro is very laggy/underpowered (also heavy on fuel) and I was thinking it could be the injectors. Going to give them a clean now that I'm feeling more confident thanks to the video.

[@StevenBTuner]

Good luck with the job - I hope you'll report back on how it goes!

[@madmikemakes3056]

Hi Steven. I just pulled injector no:4 and the needle looks very discolored (High heat) and also had carbon on the stem. The previous injector was silver with no discoloration and no carbon. Any idea what could cause that? Thanks

[@erkanisik1441]

@@madmikemakes3056 enjektör işeme yapıyor bir tamrcide ayar yapdır

[@StevenBTuner]

@@madmikemakes3056 Hi, it could be that the needle in that injector has been completely stuck at some point. What sort of results did you get with the leak-off test?

[@madmikemakes3056]

@@StevenBTuner Hi Steven I didn't do a leak off test. Need to buy a kit. It's next on my list to do.

[@anitarabar6291]

Do you have to use new o rings when you re-install , as well as silicone grease ?

[@ismetmolaahmed8336]

Hi Steven, really great explanation!! Do you know if Mercedes CDI Injectors are similar?

[@StevenBTuner]

Hi, thanks for watching! They are very similar - the leak off test and nozzle clean should work essentially the same way.

[@AdelJeffreyJeffreysAuto]

awesome steven! been wondering what type of cleaning liquid you are using in the sonic Cleaner?

[@StevenBTuner]

Hi, it is called "carburettor cleaner" and it is specifically for ultrasonic cleaners.

[@AdelJeffreyJeffreysAuto]

@@StevenBTuner awesome! Thanks for the info and great content. Your earned a sub.

[@vtecminileon]

fantastic video. Do you know if the injectors are similar on the N57 engine too?

[@StevenBTuner]

Hi, they are completely different as the top end is piezo instead of electro- mechanical - but the nozzle end is similar.

[@skatepark02]

Thanks for the amazing video! Question: only 2 of the 4 injectors I stripped down had the magnet in them. Is this normal? Perhaps the magnet was added in a revision?

[@StevenBTuner]

Hi, not all variants have the shim, but you would usually expect to have all the type in the same engine. Just make sure it didn't escape to the workshop floor if it was there!

[@Torpeero]

Great video Steven and many thanks for showing this procedure in such detailed level! I believe the injectors for N47D20C engine are almost identical, what are your thoughts on it? I might give them a good cleaning as they are out now already if the job is similar! Big cheers from Finland!

[@StevenBTuner]

Hi, thanks for watching! If you have them out already then you can do a pretty good maintenance clean by taping up the electrical and fuel connections and then suspending just the nozzles into the ultrasonic cleaner, that way you don't have to take them apart.

[@Torpeero]

@@StevenBTuner Thank you for taking the time to respond, I might attempt that!

[@thespiderkelly9589]

Hi, very useful tutorial thanks for making. Just one question, did you have to remove the intake manifold to get to the fuel line nut on cylinders 2, 3 and 4. Cheers.

[@StevenBTuner]

Hi, thanks! The intake manifold wasn't removed as far as I can remember. Another update to the video is that most of the time it should be possible to get the nozzle holes clean by suspending the injectors in an ultrasonic cleaner without taking them apart (first block up the fuel and electrical connections).

[@jedwalker4543]

Hello! Wonderful to find a good video for such a specific car. My N47 has 225,000 miles or 362k Kilometer. I’m getting ready to do a lot of major servicing including this. However I’m lacking a good set of tools for proper cleaning. I see that a completely new set of injectors OEM is fairly expensive but actually cheaper and easier to get than all of the equipment needed to properly clean. Would it be worth it to go ahead and replace all the injectors?

[@StevenBTuner]

Hi, thanks for watching! There is absolutely nothing wrong with putting in new injectors, especially if you are planning to keep the car for a long time. Your biggest challenge might be getting them to come out - so definitely get the engine really warm before you start the job.