Here are the Tools and Parts needed: Aftermarket Axle Bushing- cobratransmission.com/cd4e-sprocket-bushing-114056-1 Latest CV Shaft Drivers Side- amzn.to/2kM9DBe New CV Shaft Seal- amzn.to/2kLZrsC Bushing retaining compound- amzn.to/2jtZWGn Bushing Splitter tool- amzn.to/2IgMJ25 Bushing driver tool kit- amzn.to/2ki519m Seal and Bushing Remover- amzn.to/2kJXQ6n
@megndanhunter47915 жыл бұрын
I ordered my parts should be here couple days wish me luck..😀
@daltonkoropatnicki64864 жыл бұрын
Hey I just changed my cv axles and I drove it for about 2 weeks now and realized I had this leak will I still have to put a whole new cv axle in again when I do this repair? Please let me know love the videos so much help
@daltonkoropatnicki64864 жыл бұрын
Please let me know when you can
@shaunortman85443 жыл бұрын
This is a great video, Ford has an updated kit With a Teflon coated bushing, al8z-3b414-b . I borrowed the blind hole puller from AutoZone number 27128, and the bearing and seal driver kit from O’Reillys 67034. The job took an hour and a half and so far so good no leaks.
@jhefetz3 жыл бұрын
@@shaunortman8544 hey shaun how did you achieve pulling the bearing with the blind hole puller? auto zone doesnt' supply that loaner tool anymore so I got the harbor freight one. but since theres no backing on the bearing I don't know where to seat the puller... spreading the puller seems to just force the bearing tighter inside.
@markbuchanan43493 жыл бұрын
Mr. FordTechMakuloco, I want to say thank you for your expertise. I completed the removal and replacement of the CV AXLE bushing on my 2006 Ford Escape. You were right on the money about the time it would take to get that round little suckered out of the housing. Of course, you are faster than I am. I can't express my gratitude in thanking you. I did it exactly how you outline the whole procedure. The check is in the mail. Thank you so very much for your dedication to help the DIY'ERS!
@JerewB5 жыл бұрын
Thanks for this video! It took less than an hour to fix mine. Used a small drift punch (tip filed at a slight angle, maybe 15°) to cut two slots in the old bushing and peeled it out of there in just a few minutes with a sharp-tipped pry bar. Getting the new bushing in was a little bit of a challenge because I didn't want to cock it, which of course I did the first time. Used a little emery cloth to curve the edge of the bushing bore to make the insertion easier and went in clean and smooth. Picked up the bushing from Cobra in FL.
@freethinker78052 жыл бұрын
Do u think a slide hammer would work
@JerewB2 жыл бұрын
@@freethinker7805 the problem is that the bushing sits flat in the bore at the back, so there's nothing to grab to remove the bushing with a slide hammer. on the other hand, installing the bushing with a slide hammer might be possible, maybe even easier to keep it straight, but i couldn't justify the expense unless you have that tool already. a 16 oz hammer and a socket is all i used.
@freethinker78052 жыл бұрын
@@JerewB wat about a pair of snap ring pliers or something that can grab the inside of bushing with a slide hammer on that
@JerewB2 жыл бұрын
@@freethinker7805 nothing for the snap ring pliers to grab, that's the problem. honestly, i don't think there's a better way to do this job than shown in the video.
@kenemanuel919014 күн бұрын
Worked for me too
@oliver_klozoff2 жыл бұрын
My neighbor has an 07 that I found this exact problem on yesterday. I thought he was bound for the tranny shop, but now I'm gonna go ahead and do the repair for him. Thank you for all the details.
@baxrok2.8 жыл бұрын
Watching you work is such a pleasure. Clean, clean, clean. Check, check, check. Patient and thorough. Outstanding video work as well. Thanks so much for taking the time to share!
@evanweaver90414 жыл бұрын
Just purchased the bushing and the axle seal from Cobra Transmissions website. A local Transmission shop said that they would most likely have to pull out the transmission to replace this bushing which would have cost thousands. Now I have about 2 weeks available over Christmas to get this repair done. If it doesn't work or I break something, I could be screwed but if it does I will be very happy.
@philcollin58913 жыл бұрын
How'd it go for you? I have the same issue, starting on it this week.
@evanweaver90413 жыл бұрын
@@philcollin5891 it worked! It wasn’t easy, but I was able to get it done. The hardest part was putting the new bushing in perfectly straight without me having a bushing press. I bought two of the new bushings so I could fail once and be fine. Now it doesn’t leak and is all back together with no issues
@pac6509 Жыл бұрын
What is the part number of the seal
@pac6509 Жыл бұрын
Are you there
@jandclinan7 жыл бұрын
You sir are my Idol, lol, I've been told not to attempt to repair things such as this, I have a 2010 Ford Escape with 250,000 miles on it, my current project removing oil pan and pump to clean out, this is how I discovered the axle leak.
@projectartichoke5 жыл бұрын
Thanks so much for this video. This is a real life-saver for my 2008! You did such a great job of explaining this step by step. I can't thank you enough!
@ozzstars_cars8 жыл бұрын
Nice fix dude. I have read about this repair but never seen it done until now. I would have thought a bushing removal tool could be used but i guess there is no room back there to grab on to pull it out. Thumbs up!
@thinman86214 жыл бұрын
This video saves a lot of money. Great fix and didn't have to pull the transmission and tear it apart. Thank you.
@caferoca6 жыл бұрын
I did this service and it works great, 500 miles so far and no wobble on the half shaft. it's tight and no leak.
@WASJLS19888 жыл бұрын
Started my career as a Ford tech back in the early 80s. Boy did they build some real junk back then. Went to Toyota and stayed there 25 yrs. Good luck in a very tough business.
@jimmyfiggs62938 жыл бұрын
Nice work. Thanks for showing us how to use everyday tools to do the job.
@JustaMossKindaLife5 жыл бұрын
Awesome work! Now, being that two years have passed Is there an update on if this repair held up or if it eventually had to be redone or the transmission rebuilt?
@adamkhan87613 жыл бұрын
Any idea what the bushing and seal is for the right passenger side?
@Werewolfmage2 жыл бұрын
This video is so informative.. I have this exact issue with my rebuilt cd4e in my 07 mariner. Good to know this issue can be fixed
@andrewofford15337 жыл бұрын
A little trick I've used in the past, on those sort of things, is to shrink the bearing, by placing it in the freezer over night.
@FordTechMakuloco7 жыл бұрын
+Andrew Offord Definitely a good idea I just didn't have that option on this mobile call
@gibson76545 жыл бұрын
Wasn't there a TSB for this, in which Ford recommends a special kit to fix this issue once and for all?
@kriskinney97755 жыл бұрын
Is the bushing put in the raceway that is inside a bearing? Is that why the bushing is put in place with loctite? Does the G5M-R 5 speed manual transmission have a similar setup? The seal look different. Does the standard/manual transmission use the same bushing? Sorry for all the questions, there is not much out there on the 5 speed trans.
@nativewarrior50522 жыл бұрын
I have a '01 Escape 4cyl with the 5-speed manual trans. Any advice or tips?
@michaelthurman95983 жыл бұрын
Dude you are a great teacher....
@meangreen452 жыл бұрын
Love all the vids u make in take time to show others.
@mikeperkins48414 жыл бұрын
Where can u get the seals for the passenger side on a 06 escape 4wd
@victordelomas Жыл бұрын
I am experiencing this same problem. oil leak started. thanks Makuloco and other users for the information on tools to use plus car parts link to buy.
@cygnus5810 ай бұрын
Could you tack weld a bolt to the edge of the bushing seam and just turn it away from the housing to remove it?
@gustavomijares5128 Жыл бұрын
Need to replace the transmission mount on my 99 ford contour v6 automatic. Any video available?
@Jayson902104 жыл бұрын
Thanks so much for this! Man, this has been leaking and wearing my half shaft since I paid a trans shop to replace the bushing and seal..they didn't, Only replaced the seal outside the vehicle while I was putting a new motor in my 05. Charged me $200 for shit! Thanks again, excellent video!!
@BillMcGirr5 жыл бұрын
I’m a simple man. I could watch excellent car repair videos all day.💪👍
@bigcreekhomestead12427 жыл бұрын
Big help. Just completed this repair. Repair went as instructed.
@uc3835 жыл бұрын
I have a 2006 Escape XLT 2.3L and have read differing views on replacing the whole axle. Some say you have to remove the transmission but this video makes me think you can replace it and the bushing without doing that. Is that correct? And is there an end to end video on replacing the driver's side CV axle?
@1luxuryliner4403 жыл бұрын
I have a 2007 XLT 2.3 I just did it myself it works well I'm still working on it I'm about to put the bearing in but I used to flat state long driver bit
@philcollin58913 жыл бұрын
I'm about to attempt this on my '08 escape
@Illinoisinsulators11218 жыл бұрын
you ever think of putting the bushing in the freezer first? To shrink the molecules. we used to do it years ago when putting new sleeves in an engine
@FordTechMakuloco8 жыл бұрын
+Kevin Wise it was a mobile call so no option here
@arahtson1 Жыл бұрын
Hello, I have a 2013 Ford Escape 2.0L that has the same output shaft leak I wondering if you know the sleeve part# for repairing the problem appreciate thanks you so much.
@davidbuluku97117 жыл бұрын
i have a 05 ford escape xlt 3.0l. i followed ur video on replacing the CV axle, seal and bushing. i still cant find the bushing where can i get one?
@DanaCrosby2 жыл бұрын
I currently have a Humming noise coming from there. I thought it was the wheel bearing so change it but noise is still there. but no leakage from seal
@billyr98408 жыл бұрын
Dude, that was a sweet repair !
@tylerp2916 Жыл бұрын
Hi, when i took my halfshaft out the bushing came out with it and it is very loose on the shaft and loose in the case. does this mean inside the case worn out too? if i order a new bushing will it fit tight?
@erichn42913 жыл бұрын
Question. Im doing this repair the bushing was paper thin and the trans side of the shaft was beat up. I have a new shaft my question is does the bushing end up into the sprocket or close to it?
@jessev21978 жыл бұрын
Flip that socket to give a better drive surface. I use it that way so the edge of socket doesn't do edge of bushing nicking. This reminds me of the right side support kit for older Taurus. Same problem over again. Some things never change with Ford.
@tyronemaye19493 жыл бұрын
Now would the notch in the bushing piece your pressing back into it is it 12 o'clock as its re set into the space of the axle in the transmission?
@jaybilawchuk22254 жыл бұрын
could this not be done carefully with a dremel tool in two spots and then it'll fall right out?
@1122ss7 жыл бұрын
Excellent video as always. Besides a leaking seal, would a high speed shimmy be a symptom of a worn bushing? How about using a dremel to cut the bushing?
@hailblue2217 жыл бұрын
Well I changed just the seal and it was fine for about a week, now leaking again.... it looks like I have to change the bushing and 1/2 shaft. I'm just nervous to cut out the old bushing, I actually chewed up the seal aluminum a little🙁 but I watched another video and the guy said it's ok if u mess up a little in the outside for the seal since it seals in the inside!!! Any tips would be great on the bushing, is there a point in the bushing were there is a Seam?
@FordTechMakuloco7 жыл бұрын
Any point is ok when using the bushing cutter listed. There is a seam but it is a tongue and groove style so that wont help.
@gustavomijares5128 Жыл бұрын
Do you have a video for a 99 Ford Contour SE 2.5 automatic transmission on How to replace the seal / bushing? Thanks
@FordTechMakuloco Жыл бұрын
no sorry
@gustavomijares5128 Жыл бұрын
Will this Bushing CD4E will fit my vehicle?
@gustavomijares5128 Жыл бұрын
Thank you for the video . It saved my car, was ready to junk it
@AlexRodriguez-qp7ju3 ай бұрын
Hi, I have a Ford Escape 2012, 4 cilinders, 2.5L, due to a ATF leak the automatic transmision failed, a mechanic came and scanned it there were two codes related to the AT, he said it had to be flxed or replaced, I dont have the money to pay for it. I have fixed my Escape several times thanks to your videos, but now is a little more complicated since I want to fix the AT myself, do you have any videos on how to do it? It would help me a lot, since I havenot found nothing that specific I live in El Salvador Thanks in advance
@craigroush51862 жыл бұрын
I have a 2010 Fusion with a g6m manual transmission. The transmission seal was leaking on the drivers side cv shaft. The repair shaft replaced the seal but said there was a pretty good groove on another part, not the cv shaft. I am thinking they were talking about the bushing now. They could not find the part from Ford, so transmission is still leaking. Would you think this bushing is what they are referring too? Thanks
@MERCNRY Жыл бұрын
I wonder if cutting at the notch would work?
@DavidDavis-gp7th6 жыл бұрын
The CV axle broke on my wife's 03 escape, replaced the axle but it never felt like it seated no matter what I did. I put it all back together and drove it down the road and back, tore it back down and checked to see if CV axle was seated and it seemed to be. I put it back together and seemed fine. I drove it up on a block so I would have clearance to change the motor oil and trans fluid started pouring out from the seal where the shaft goes in. I backed it off and pulled it back up and no more leak... Drove it a few more miles, including an off-road Hill climb, brought it home and parked it overnight. I got in it this morning to check the trans fluid and it had leaked some overnight in the driveway... Seems that if the axle is in a bind it leaks. Would you think that the seal and bushing is damaged and needs to be replaced too?
@wilmalee45784 жыл бұрын
I have a question about my 2006 ford escape, 3.0 all wheel drive. Is there a bushing that goes on the front passenger side inside the transmission, if so can you give me some advice on how to replace it. Is it the same type of bushing that goes in the driver side? The driver side bushing doesn't move but the passenger side does and i can not seem to find any information about it. If you could help me, i would appreciate it. thanks.
@BillyTpower5 жыл бұрын
awesome video. would this be similar in a ranger 4x4 however mine is a 2010 has anything changed? I'm hoping that the have left enough room behind for an expanding arbor slide hammer tool.
@Motorcycledad160Ай бұрын
Saved me so much money. Thank you! ❤
@Smokeless11676 жыл бұрын
We have a 2005 Escape that we got for our daughter and it has this issue. At least it is not an expensive repair.
@FordTechMakuloco6 жыл бұрын
Trouble is finding a shop to do it.
@pltmann2 жыл бұрын
Getting ready to do this to my CD4E. I have a new bushing and rebuilt drive shaft. I checked the bushing on the shaft and its not real tight fit. I would think it would be a pretty snug fit. Was yours like that?
@brentmunroe309718 күн бұрын
Thank you sir 🙏 you just don't no how you just help me with my ford escape 2.3 2008. Thank you again sir
@jonathanmurray18635 жыл бұрын
I bought a 03 Ford escape and it looks like the shaft twisted and the pump broke the gear in center but did it hurt the converter because put it back together and the car won't move I think they broke convertor with misalghing shaft
@jonathanrivera2912 жыл бұрын
I have a ford escape 2011 xlt 2.5l the same Problem ..do the part fit my to
@absurdspeed5 жыл бұрын
Desperate. Please help. What transaxle/ptu is in my 2006 Escape XLS 5-speed 4WD? it looks nothing like the Mazda G5M in the FWD models and, the passenger side half shaft does NOT pass through the ptu.
@pacheco4644 жыл бұрын
Mr . I got one 07 2.3 you tink the engine fit from hybrid and transmission? Same as 2.3
@Ashroyer866 жыл бұрын
I have a bearing like noise front passenger side. Replaced wheel bearing which is now silky smooth but noise is still there. I pulled the whole drive shaft including intermediate shaft. The carrier bearing flange wiggles a bit back and forth, is that normal? I put my finger inside the transmission where the shaft goes and I felt a good bit of up and down play on the internal splines is that normal?
@campermike88798 жыл бұрын
How has the Ford 5.0 in the truck been holding up? I haven't really heard much. I'm looking at one. I don't want to deal with the ecoboost problems
@jerrymora41042 жыл бұрын
Awesome work as always...any chance you have a video for the passenger side?! Sure could use it right about now 😟
@chopperboy4204 Жыл бұрын
Should be the same I’d think
@hailblue2217 жыл бұрын
Will this work for a 2002 escape? And if I freeze the bushing do I put it in frozen?
@FordTechMakuloco7 жыл бұрын
+Joe Thomas yes it will and if you freeze it you install it frozen
@Solitarioguerrero-t8r2 жыл бұрын
and which one is for ford escape xlt 02 3.0 seal transmission axle
@Solitarioguerrero-t8r2 жыл бұрын
What stamp does my car have? Ford escape xlt 02 3.0
@ag74648 жыл бұрын
great videos. I need some help on a 03 ford expedition 5.4L keeps saying check ADVTRAC and can't find to see if I need to replace a sensor or a cable.
@Cdjmwilson402 жыл бұрын
Do I need to purchase a seal also once the bushing has been replaced?
@eddiehaskell1957 Жыл бұрын
Yes
@tbone113816 жыл бұрын
Mine spit the bushing out going down the road it was stuck on the Axel is that common or should I look for another issuse
@FordTechMakuloco6 жыл бұрын
They can get pretty loose when they fail yes.
@tbone113816 жыл бұрын
@@FordTechMakuloco so Axel failure then the wieght of the axle just pulled it out I'd hate to buy all the parts to find out the trans is bad it still drives tho
@StStephen727 жыл бұрын
Tks, I just ordered everything. Hoping to try this repair next week.
@bobbymolak33642 жыл бұрын
Would this same process work on a 2013/2014 escape ? Any help would be much appreciated. Thank You ✌️🙏
@FordTechMakuloco2 жыл бұрын
The 6F35 already has a bushing kit available from Ford.
@bobbymolak33642 жыл бұрын
@@FordTechMakuloco , Yes my apologies, I should have emphasized the process in which you removed and installed with the chisel .let me know. Thanks for the response and Have A Great 4th 🇺🇸🇺🇸🇺🇸
@FordTechMakuloco2 жыл бұрын
You can use the special chisel but it is best to use a blind bearing remover set.
@fernandomorales52193 жыл бұрын
What size of metal bushing does the Mazda tribute take
@32jetjet8 жыл бұрын
a different topic I got a new fuel tank install on my 13 f150 ecoboost and now engine light code P0430 codes is showing you think having the new tank has something to do with the code
@chrisniebuhr88347 жыл бұрын
Very Nice Video! my daughter 2006 Escape has that issue put two seals in it and still leaks Looking for the Part # Shaft and Seal and bushing or anything else you would need when it is tore apart and where do you recommend getting them? Thanks for your Help!
@FordTechMakuloco7 жыл бұрын
Everything you need is linked to in the video description.
@blueexpresstv54012 жыл бұрын
I followed this instruction and replaced my leaking front driver shaft!
@snw568 жыл бұрын
Super job on this one!
@Bump-mw6vk7 жыл бұрын
are doing the rear brakes with disc the same as the front on a 2006 escape with automatic 4 wheel drive?
@Niterider734 жыл бұрын
I think this is what happened to my 05 escape. I just pulled the knuckle along with the axle out and the bushing it's just hanging on the axle shaft.
@tamarabomia3820 Жыл бұрын
Thank you for taking the time to do that in rel time
@bayfieldmurphy12873 жыл бұрын
Anyone know if you can replace the pump cover on these mines rusted out
@denyceberard39792 жыл бұрын
Mine was a 2013 Ford Escape and the bearing didn’t have a notch. My part number from Ford for the: kit 9L8P-7H260-AC Which includes Tool 9L8P-4N206-AB Bushing DV6P-7E110-AA Half Shaft Seal 9L8P7H260-BB
@zioncurran59115 жыл бұрын
I have a 06 ford escape and am having a knocking noise on acceleration and decelartion on turns. I have replaced both CV axles and noise has continued. My guess is it is this bushing 96060 which is allowing the cv shaft to move around in the transmission. I can see movement on the inward joint on the drivers side.. I don't want to take it to a transmission shop if this is whats causing the issue.
@zioncurran59115 жыл бұрын
Cant wait to try it.
@zioncurran59115 жыл бұрын
The last tip of the video was very helpful.
@redroofretriever8 жыл бұрын
Why not freeze the bushing before install? Would make the pressed fit faster, with less chance of inadvertent damage.
@FordTechMakuloco8 жыл бұрын
+redroofretriever it was a mobile call but yes otherwise it would definitely help
@wilE67646 жыл бұрын
redroofretreiver..what do you mean by freeze the bushing?
@hardcoretrout Жыл бұрын
Amazing job there Good Sir.
@ДаулетМолдакасов-в4т3 жыл бұрын
Привет не знаю английский язык, знаю русский. Привод начинает болтаться в своем посадочном месте при износе этой втулки? Я правильно понял...
@fairbornCCF6 жыл бұрын
I have replaced my seal a couple times now. Usually holds for a couple years. I now suspect the bushing is also bad, but am wondering if bad motor mounts are the cause.
@OABrown4 жыл бұрын
I would think that the CV needs to be replaced as well.
@ozzmann32178 жыл бұрын
Chey man was wondering if you have any suggestions... I have a light clunking sound when power goes to the rear end of my 2014 mustang gt, rear end seems fine, but I'm curious if something in the drive line has become loose... let me know if you have any suggestions have any questions to help I'll supply the answers
@christianmorrissey78397 жыл бұрын
Hi mate, I just watched your other video on this seal. I am in Australia and have a Mazda Tribute 2005 3.0 and I have fluid leaking from the right hand side seal where the CV Drive shaft enters the transmission. Is it the same deal left or right? Also where can I get this seal repair kit with bushing if its the same as the left?
@Andrew-xw2xj6 жыл бұрын
wow thanks thats just what my mazda is doing and after pulling the axle the bushing came out with it didn't know what it was till i saw your post awsome can you tell me where you got the bushing and does the passenger side have the same kind of bushing if so where did you get the chissle you used and the bushing tool thanks alot very informative and useful
@alejandrodelacruz94196 жыл бұрын
How do you change axle seal on passenger side
@alow23238 жыл бұрын
Really need ur help on a 2014 Taurus sel strut removal can't find anything similar
@anthonyfili118 жыл бұрын
i believe those are the style where you have to remove the lower control arm to allow the knuckle to slide down far enough to fully slide off the strut
@alow23238 жыл бұрын
Anthony Filice I appreciate that! Have you came across any video?
@anthonyfili118 жыл бұрын
No I just know because I am a ford tech as well
@alow23238 жыл бұрын
Anthony Filice ok cool
@kirkd.29976 жыл бұрын
Thanks for the video! Where are you located and how much would you charge to do this?
@wesleymatthews34443 жыл бұрын
Awesome video, especially thanks for posting up parts numbers!!
@joonajks4 жыл бұрын
Is this Transmission reliable for daily driving use with proper fluid change? Looking at a used 2002 Ford escape with over 200,000 miles!
@Clamjammer4 жыл бұрын
Joon kinloch these cars are shit. I know this is old and I hope you didn’t buy one. Get Japanese instead. Honda Toyota hell even Kia hyaundai
@OABrown4 жыл бұрын
my 08 escape hybrid passenger side is leaking fluid like a mofo, i guess i'm looking at something like this >___< I can't seem to find a CVT specific exploded guide or walk through.
@pedrowalter4 жыл бұрын
I remember the mechanics in my town use to punch scar the surface where the bearing or bushings will fit. So they won't move.
@ysrpilot8 жыл бұрын
Would it be a good idea to freeze it first to make it go in easier?
@djr34858 жыл бұрын
Being a mobile call it probably wasn't practical I guess. But yes, using the physics of temperature when removing/fitting interference parts reduces much of the struggle.
@ysrpilot8 жыл бұрын
DJ R True, but I would've had the bag of them in the freezer the night before (or outside in the Chicago area during winter) and stuck them in a cooler in route. Still worked out.
@hailblue2217 жыл бұрын
OK I just called a transmission shop they said if all my fluids on the driveway which it is and it's bright red and he thinks it came from the upper bushing so he said the trans will have to come out over $1000 repair does that sound right to you
@FordTechMakuloco7 жыл бұрын
+Joe Thomas upper bushing? not sure what they think they are talking about
@FordTechMakuloco7 жыл бұрын
+Joe Thomas if they are referring to this oh axle bushing then no they can do it in car as shown.
@hailblue2217 жыл бұрын
I'm new to this stuff! I just talked to another shop and he said if there is minimal play in the shaft that I probably just need a new seal, he also mentioned that the bushing always doesn't go bad. Boy I wish I could talk to u live lol
@hailblue2217 жыл бұрын
FordTechMakuloco The guy said that there is another problem area that can leak something upper!! And trans would have to come out this was probably someone trying to scam me
@FordTechMakuloco7 жыл бұрын
+Joe Thomas yup unless they can specify a bushing number run!
@joncart58346 жыл бұрын
Is it possible for the right side to leak also or is it common
@derfstang4805 жыл бұрын
I'm on a Ford Escape forum and have been for many years. I have yet to come across this type of leak occurring on the passenger side axle from the same cause.. The reason the left (drivers) side gets this leak is that the CV shafts inner joint articulates within this bushing. The right (passenger) side has an intermediate shaft that doesn't articulate so you have significantly less wear. I'm not saying it's impossible for this to happen to the passenger side but, it's not very or not as likely.
@ladonnad.steele24708 жыл бұрын
Love your videos!!! Good clear and concise.
@joncart58346 жыл бұрын
Will this repair work for a 2003
@BatteryGeekReviews7 жыл бұрын
Hope the works for my 06 mazda tribute
@roadking9517 жыл бұрын
that was the best video ever very good job, with all info you need TY Brian really knows what he is doing and can explain it well