2001 Honda Odyssey P0325 Knock Sensor Repair, Solved

[@Cthulhuman]

Just did this to my 2000 Honda Odyssey. Same exact problem rat nest and chewed wires and all. Thanks for the video keep up the great work

[@Alex_Justified]

I need to do this for my car in a couple of days. Imma head to harbor freight to make sure i have all the right tools. Thanks for the video

[@thomasbriansavingmoney]

you got it, thanks for watching.

[@Alex_Justified]

@@thomasbriansavingmoney I had to end up taking a piece of the engine to get to the sensor because I wasn't able to fit anything through the hole with the swivel. There was some very annoying bolts around it, but I finally got it done and was able to smog my van.

[@johnb2614]

Like your method....... I did it myself too and saved over $425 that it would of cost me if I hired a mechanic to install the knock sensor. Its the Labor that costs the most because the knock sensor only costs about $27 - $39 dollars depending where you buy it. My knock sensor cost me $27.00 It took me a total of 3.75 hours from start to finish....but well worth it.

[@thomasbriansavingmoney]

thats great ! good job ! thanks for watching.

[@haileysimmons663]

Thankyou for your video, do you know if the sensor is in the same position on a 2006 model odyssey.

[@ZellenoffBloWZ]

Great video , have same job broken wires and knock sensor broke in my hand , I actually was able to get my hand under the plenum chamber rather easily , so no removal of the intake or fuel lines at all

[@golfish8589]

Did tor TCS light come on withe the knock sensor problem? Thanks

[@WICKEDWINGSNSPICE]

How did you get the pigtail out?

[@jekks296]

Thanks for the video. Is this the same location for a 1999 and does the wire go under or over the metal part?

[@shanewhite5870]

Hello... what type of lube used for injectors? Thanks

[@rdjhm]

thanks my amigo for the video

[@raymondchapman5990]

I have a 1998 Honda Accord 3.0 V6, is the knock sensor in the same location ? I have looked and cannot see one. Thanks.

[@WICKEDWINGSNSPICE]

Ok i did everything but, how do I get the sensor out of there??? What tools to use? I see it but can't get to it???

[@fredcarrado9146]

The crayon idea is great

[@SG-gm6zo]

Curious how you got the sensor back in and aligned with the hole?

[@thomasbriansavingmoney]

It should just slide right in. thanks for watching!

[@chazzy97akm]

What type of socket u used? I have u 1/2” drive 24m/6pnt but can’t fit through hole to get to

[@jcfel5136]

@@chazzy97akm same problem here as you need deep socket to be able to fit around plastic top of sensor. Did you ever figured it out?

[@mariasebastian4260]

What size socket was used to put the new one in

[@thomasbriansavingmoney]

i used a 13/16 deep socket. thanks for watching.

[@mrh0ck3y]

Is your magnet the magnet of a speaker? 😂😜 genius. Those magnets are stronger than the ones on magnetic trays

[@h20dies]

You didn't even show how you got the pigtail out

[@josealfaro9514]

Poor job on the pig tail connector.

[@HighMXHubby]

You left out the hard, important parts...

[@thomasbriansavingmoney]

sorry it didn't help you.thanks for watching!

[@فيصلالمطيري-ط8ر7ذ]

هلا ارجو اضافت الترجمة العربية الى المقاطعة

[@thomasbriansavingmoney]

نعم يمكنك ، شكرا للمشاهدة. nem yumkinuk , shukraan lilmushahadat.

[@h20dies]

You didn't even show how you got the pigtail out