Taking out And cleaning the two shift solenoids and doing transmission drain and fill
Пікірлер: 116
@falkononskiis45492 жыл бұрын
Thank you so much for the detailed video. This cleared up the delay in shifting. Testing the solenoids with 12v power before you reinstall them is a must - there should be a clear, audible clicking sound, nothing "muddy" or "plugged up" sounding. Cleaning out the tiny filter cylinders as well as the valve body will help tremendously.
@671DDA Жыл бұрын
I replaced the transmission dual linear solenoid pack. Problem solved. My 2004 Honda CRV with 147,500 miles shifts normal. Thank you for the video.
@stephanielosh20125 жыл бұрын
Thanks for the video. I've been looking for quite a while for something that showed me just what I needed to remove. Thanks again.
@MapleMarmite5 жыл бұрын
Great video - nice and clear to see what needs to be done! I will have a go at this on my 2004 CR-V. I've done the triple fluid change already but not the solenoids. Thought it would be more difficult than this but it looks straightforward from your video. Got a hard shift from 1st to second and occasional delays in shifting further up the box, too, now. Good vehicle otherwise so I want to keep it going, although a new transmission would probably be more than it is worth so hoping this will do the trick. Thanks for posting this.
@ROMEYYOUROCK5 жыл бұрын
Did it work?
@MapleMarmite5 жыл бұрын
Unfortunately it didn't work on mine. It came apart easy enough and I was able to reuse the same gasket but she still does the hard shift 1st to 2nd. I have got a set of used solenoids from a CRV that was junked because of rust - it ran and shifted fine so I'm hoping that might fix it. Otherwise it's a transmission and I don't think I can justify the expense on this rig. Shame because it's not too rusty for an East Coast Canada car.
@IzaguirreC5 жыл бұрын
@John Doe same, the seal was stuck on both solenoid and transmission. Took me a while to clean it up. Its shifting way better. I only replaced the top one since it was such a hassle to clean it.
@khat17 Жыл бұрын
Many thanks for this info. My specific issue: Was getting P0750 and P0780 when scanned. When warm there was occasional hard shift to 2nd and it wouldn't always shift to lower gears when you step on it. Cold start and reverse worked, but drive would delay with hard shift then the drive light would flash constantly and each subsequent shit would be hard. A switch off and start again would correct that. It hasn't been 2 days yet but the instant performance boost in shifting was seen after cleaning up. No more DTCs either. Only issue is I had to reuse my gaskets as I couldn't find replacement ones online. Many, many thanks!
@tatialo373 жыл бұрын
Cool video!!! Thanks for the update!!!
@671DDA Жыл бұрын
I'm doing that procedure on my 2004 CRV. I appreciate these videos. I just have one comment. Before working under the hood, the first thing to do is disconnect the battery!
@eaglerider945 ай бұрын
And power wash, at least the area one is going to work around
@opinionsvary31322 жыл бұрын
Cheers mate... 4 bolts on top solenoid and "6" on side one.
@Bigjamez20114 жыл бұрын
Don’t forget to clean the magnet end of the drain bolt off .
@Mrpdids14 жыл бұрын
So if you’re watching this video number one do this at your own risk. Most of you are here because someone before didn’t change their transmission fluid on time. For those of you doing this or attempting to do this you could just change the fluid and drive around for 500 - 1000 miles and change the fluid again until it’s clean. Save you some time. This is last attempt and if you do this and it ain’t right, it’s cause you didn’t do it right. I wish you luck and gods speed.
@MarketingCoachKen4 жыл бұрын
I have 04 Element. Super hard 1-2 shift. Found vids about dual solenoid. Changed it today (OEM) and now 1-2 shift like butter. But! 3-4 started to shift harsh/slip/hesitate, and harsh slow downshift into 1st gear. Going to try solenoid on top tranny and see what happens.
@howtofrank5024 жыл бұрын
EZ20NOWTurboCharged with the harsh 3-4 shift I’d try replacing your pressure switch.
@TedLynchMusic3 жыл бұрын
@@howtofrank502 Why do you say change the Pressure switch for a slipping 3-4 shift? WHere is that located? That's exactly what mine is doing as well.
@jacksonevans9378 Жыл бұрын
So I have been concluding this is what is wrong w mine. It is HORRIBLE when cold. But when it gets warmer is not as bad but it still doesn’t shift well as I know it should. Would that still be consistent with a bad solenoid? Thanks JP
@saginaw60 Жыл бұрын
There exists something called a shift improvement kit, with special springs and drills to enlarge oil passages. Be nice to know if this is any good.
@mrbino1112 Жыл бұрын
What’s the name of those skinny tubes after removing the solenoid? Where you specifically said to take them out one by one it may be sticky?
@Official_C.G.1 Жыл бұрын
When your transmission solenoids are bad do they normally throw a check engine light code?
@samettuon353 жыл бұрын
Would that be an issue for my 2004 crv as well it drives well then sometimes it feels as if the brakes where being held down and won’t move sometimes I would floor it to move it till the temp goes up as well i was thinking the brakes were locking up but this seems more logical help please thanks
@angelisone4 жыл бұрын
Please share on 2005 CR-V 2.4L gaskets & O-rings numbers for both Shift Solenoids?
@8754roberto3 жыл бұрын
Hello if you could help me, I have a 2007 Honda Civic lx, in only has trouble shifting when going uphill , and on 4 to 5 ⚙️ it doesn’t hve any codes , only once it gave me a shifting solenoid stuck open .. but for now no codes
@chamirf Жыл бұрын
Any idea as to where to find the gasket for Solenoid A? The smaller one on top
@mikon32703 жыл бұрын
Did you have to replace any o-rings on those little cylinders?
@josemanuelsilvasanchez8151 Жыл бұрын
My honda accord has just the same solenoids but all I need to know is what is the resistance in ohms they should have, right now the measurement with the multimeter is 6.6 ohms but i don't know if it's okay or not I couldn't find any information anywhere. Please, help :(
@michaelmasocha35552 жыл бұрын
Hello i wanna ask my crv model 2005 sometime when i drive for constant speed of 80km/h or any speed constant for long distance when i speed the car reeves as it it on neutral what may be the problem
@ozzydoop14733 жыл бұрын
My HONDA CRV 2002 sport started thumping into the gears change & eventually it began slipping & now it won’t engage into 1st gear : I am trying the LUCAS transmission slip fix fluid & so far I have had minimal success : & when in drive it goes ok under 2000 RPMs : I also have the D light blinking at times : still testing now so I’ll keep this post updated if anymore success or fixing from the Lucas fluid :
@starkeymorgan41422 жыл бұрын
What ended up happening?
@beachwave2 Жыл бұрын
Any updates ? Anything worked for you ? I have really hard shifting in 2nd and 3rd :( Please let me know.
@lisacrawford6948 Жыл бұрын
Me too hard shifting second and third gear 05 element
@alliemercado3825 Жыл бұрын
JP I am having trouble getting the second one off can you please explain that better I got the top two bolts off and the two middle ones off but the bottom ones I can't find them
@anthony2009accord Жыл бұрын
Can you tell me what shift solenoid controls 1st-2nd shift?
@santanaduran97022 жыл бұрын
Hey when you took the shift seal off did it leak any fluids
@schmidt76ful2 жыл бұрын
Which solenoid is first going into second is it the dual solenoid
@rupeshbadgujar20023 жыл бұрын
My crv 2004 model gear not shifting if i put it in Park mode. The car needs the key to free the gear from park mode to drive mode
@menyar44443 жыл бұрын
I have a 2004 Honda Jazz while I'm on the road and the automatic transmission shuts off. Can you help me solve the problem
@FcDominick5 жыл бұрын
Did it actually fix the problem?
@cheddarballs8642 жыл бұрын
Mine was low on trans fluid. Transmission gasket had a slight leak
@Juanimo75 ай бұрын
Is this what the problems is when I slow down to come to a stop… the last downshift into 1st gear jolts the car and almost dies?? Is this the cause?
@franciscoesparza41010 ай бұрын
My accord 2003 ex 2.4 liter I think my transmission is giving out but I’m going to replace all Sensors can some sensor from transmission pop up a code
@Huss300Ай бұрын
Please help... I have a honda accord 7th gen 2.4L automatic i have problem from shifting 1 to 2 , i think it is this dual linear solenoid as it only shifts from 1 to 2 if i only let off the throttle but it shifts perfectly when it shifts to 3 4 5 So i have a doubt that will the solenoids of 8th gen 2.4L accord will work on the 7th gen 2.4L. Can anyone help me by seeing whether the 8th gen accord solenoid will work on 7th gen accord 2.4L Note: the part numbers of 8th gen and 7th accord Solenoids are different but they appear the same (Sorry for my bad english and a huge discription)
@eddycoronado83813 жыл бұрын
👍
@pooddescrewch87182 жыл бұрын
Don't these so,enoids have to be torqued down ?
@michaelpincavitch52452 жыл бұрын
Its a good idea to use compressed air first to clean any loose debris first so none ends up in tranny !
@richr10292 жыл бұрын
my 2011 CRV LX has this issue.. just ordered and OEM part with gaskets to replace....
@xing280910 ай бұрын
thanks
@lisacrawford6948 Жыл бұрын
Where can I find a dual shift solenoid?
@vinnyf66353 жыл бұрын
Does the transmission have to be drained before changing the solenoids?
@fidelrivera47802 жыл бұрын
El chicote se sale al momento que meto cambios y ya no regresa se queda duro la palanca y manual lo tengo que regresar para que los cambios den es automática Honda crv 2007
@alliemercado3825 Жыл бұрын
Is there like a part 2 or something?
@lawrencedabney5580 Жыл бұрын
I got a 2004 CR-V 5speed having hard shift and the clutch is low
@briang8964 жыл бұрын
What about a hard downshift 2nd to first? On an newly rebuilt AT transmission. Shifting up is super smooth
@wilbert34904 жыл бұрын
Brian G u need replace the one on the side of transmission
@phoenixdickey24984 жыл бұрын
@@wilbert3490 on the side, or on the front
@abdullahazeez27333 жыл бұрын
I have same problem
@ketchupmustard54653 жыл бұрын
Its been a year. Did you try this to your crv? Or can you tell me what it took to fix it?
@briang8963 жыл бұрын
@@ketchupmustard5465 I had taken it back to the place I had the work done, since I have a 3 yr warranty. They opened back up, replaced some small part they thought it could be. But issue is still there. I took it somewhere else, they even said it’s not a big deal 🤨 but like I told them it wasn’t doing it b4 I had the work done originally.
@jessicagrigsbatompkins162611 ай бұрын
i have an 06 CRV that has the blinking D and will NOT shift at all. changed the top solenoid and now throws a solenoid low voltage code. What could that possibly be? I have asked a couple people and several different option including changing fuses.......any comment would be appreciated
@mtjm5 ай бұрын
Did you use oem or aftermarket part?
@raging_carnut4 жыл бұрын
I did this exactly alone with the iacv cleaning. It shifted horribly afterwards and it would knock and move forward on idle park neutral etc. Had to take it to the dealer to get it fixed. Just did it because it would drop from 3 to 2 roughly
@MarketingCoachKen4 жыл бұрын
How much dealer charge and what was diagnosis?
@ellocotron83584 жыл бұрын
My 2004 CRV shifts hard from 1st to 2nd but only does it sometimes. I replaced the solenoid on the side of the transmission and it was shifting perfect for the first 5 minutes of driving it then it started doing it again. Should i replace the top solenoid also? Idk what to replace next to try to fix this problem
@chardthomas51404 жыл бұрын
Whats is the code p0748?my D light is blinking and looses power when climbing hills?first gear,2nd gear and drive all av the same power
@j4n83benja3 жыл бұрын
Did changing the top solenoid worked for you?
@renzrenz34653 жыл бұрын
I have same problem.do your problem fixed already?
@davidcarrera61783 жыл бұрын
good friend greetings I have code 5 in D4 that will be that failure honda accord 2000
@Mrpdids15 жыл бұрын
Of course it fixed the problem, I’ve done this on many Honda’s not just CR-V’s, lol
@MapleMarmite5 жыл бұрын
Thanks for listing that video - just watched it so I can test my junk yard solenoids before fitting. Still hoping I can save the car - trans rebuild or replacement would be too costly. Cheers!
@MapleMarmite5 жыл бұрын
That may have been the case with mine but not sure. It was very well looked after in other respects but most people don't even think about changing transmission fluid.
@glasser28194 жыл бұрын
the screens are here to protect contaminant pieces from jamming the solenoid plungers. Course screens are not designed to be particulate "filters" for clutch material. 😊
@rupeshbadgujar20023 жыл бұрын
Plz give solution i need it very urgent
@65gtotrips8 ай бұрын
Well ? Did it fix it ?
@thexflexclan4 жыл бұрын
Hey did you really have to remove the battery tray ?
@juangaytan84673 жыл бұрын
Don’t have to if you have the patience but it’s makes it a lot easier and gives you the extra room
@coryd91554 жыл бұрын
What’s the torq spec for solenoids
@stevelehman39693 жыл бұрын
8.7 ft lb
@pooddescrewch87182 жыл бұрын
I looked it up and 8.7 is spec but advise to go 8.0 first and start engine to see if leaks apparent . Appernently over torqueing is a huge no no ...every thing I have read advises to creep past 8lbs if need be and stop on the smallest number that doesn't leak .
@xMrBlack Жыл бұрын
Anyone else have the issue where when slowing down it feels like the brakes almost take over on their own and makes it feel like you tapped them too hard or like it's suddenly dropping into a lower gear while slowing down?
@johnathanolmo8198 Жыл бұрын
Yes did you find out what was causing it?
@xMrBlack Жыл бұрын
@@johnathanolmo8198 unfortunately not yet. A family member has an 05 crv and she says it does the same thing. I'm wondering if it has something to do with the stable track
@johnathanolmo8198 Жыл бұрын
I had a code P0845 just drained and refilled the Trans fluid and changed out the 28610-RAY-013 pressure switch on the trans problem seems to have been fixed
@xMrBlack Жыл бұрын
@@johnathanolmo8198 the only code I'm getting right now is for the vtec solenoid rocker arm crapping out. I didn't have a code prior to that though. I'm sure it could use a fluid change at this point, I'm sure it's never been changed. I'll look into that and the pressure switch.
@Eddie312. Жыл бұрын
@@xMrBlack sir that issue is your vvt solenoids (based off the code you mentioned). Switch those out (very easy) and reset the code a long with a oil change and it’ll drive like new.
@lebronjordan8025 жыл бұрын
My 2002 crv has p0750 code shift solenoid A, Cel and blinking D drive. Which one is solenoid A ? Should I replace the selonoid or just clean it? ...thanks
@davidgutierrez82974 жыл бұрын
Just replace them both. If ones failing the others not far behind.
@lebronjordan8024 жыл бұрын
david gutierrez thanks
@glasser28194 жыл бұрын
expensive guessing...
@Mrpdids14 жыл бұрын
Replace
@ctopseuge94734 жыл бұрын
Is it okay to drive?
@MrBigal1231235 жыл бұрын
Problem fixed?
@glasser28194 жыл бұрын
since the shifting valve screens were clean... then it is just like an ATF change alone, right?
@dan98094 жыл бұрын
Please list part #s for gaskets, provide links or official names for the gaskets needed for this process
@dan98094 жыл бұрын
Mine is a 2004 CRV EX, 4 speed automatic transmission and 4 wheel drive
@Mrpdids14 жыл бұрын
28262-PRP-000 Is the gasket for a 2005 - 2006
@lisacrawford6948 Жыл бұрын
Do u take out the solenoids our and clean them?
@dan98094 жыл бұрын
2004 CRV sometimes slips between 1&2 gear then shifts really hard into 2nd. I recently did a transmission fluid flush (changing 3 times in a row) but it didn't fix it. It only intermittently shifts hard into 2nd gear. Will this fix it? Please, thank you
@Mrpdids14 жыл бұрын
Check Solenoids and replace or you might need a new transmission
@dan98094 жыл бұрын
@@Mrpdids1 thanks
@renzrenz34653 жыл бұрын
Did you fixed the problem?
@williammize82703 жыл бұрын
My fluid is past due to b change😂😅🤣🌞😳😲🙈d but its still shifting ok
@aungsoemoe5242 Жыл бұрын
Honda CRV2002 Shift Malfunction
@moisesaberjedo548811 ай бұрын
Aaà.aaa.à ..
@ericmadx30633 жыл бұрын
This doesnt work all the time been there do ne that even put new solenoids and nothing
@danielmilbourn36493 жыл бұрын
What was your fix?
@ronettetyson8564 жыл бұрын
Hit a deer now the car want shift out of second gear