2003-2007 Honda Accord Throttle body cleaning

[@M0N0T0N0US]

DONT PUSH IT OPEN WITH YOUR FINGERS! , turn the key to power on, dont start it, power on. push the gas pedal and it will open. Wedge the gas pedal down or have someone push it for you. Open and close it as you spray the 2 sides where the butterfly spins. That’s where it gets sticky and needs to be sprayed while you opened and closed it until it loosens up and smooths out like new again.. apretiate the video for an example to send to a friend tho.. ✌️

[@stephenarling1667]

Why not push open with fingers? Will it damage the stepper motor?

[@brooklyn7941]

@@stephenarling1667 yep

[@crispa1861]

So when you do the procedure as you suggested, will idle learning procedure still need to be performed? Thx

[@ajmontgomery4564]

Ive used my fingers to push open on multiple vehicles for yrs and never once broke anything, just have to know the limit, also to actually clean it needs to be removed from the vehicle completely and thruoghly cleaned

[@terrywawro2951]

This did not work for our 2007 Accord. I had to manually open the butterfly valve.

[@terrywawro2951]

Thanks. This fixed the hard to find intermittent hesitation in our 2007 Honda Accord.

[@1eleven177]

Dude holy fuck!! That’s was so easy !! My car was acting up, thought it was transmission, so I took it to a shop just for the guy who works on transmission to say it was electrical, went to an auto body shop, said they couldn’t work on it till Friday, went home KZbin everything I thought could work and this was it!!! Thank you!!

[@1eleven177]

My shit wasn’t plugged in !!

[@npetzold]

all of your videos on 2006 honda accord... are so awesome.. it saves both time & money. i couldn't ask for better..

[@NutzAboutBolts]

+Npetzold Npetzold thank you! :) We didn't know it was such a common car haha

[@npetzold]

i didn't either... i thought i was exclusive..

[@rickyazarro1813]

Tell me why he sounds like Toby from the office

[@villafontananorte]

I did it two hours ago to my car and I did not touch the butterfly. Don't touch the butterfly, period! It did work. I removed the negative battery connector first before taking everything off. In the meantime, I also cleaned the mass air sensor with an especial spray. Let it dry for 5 minutes. Put everything together and boom, the engine light is gone! 10 minutes process. A mechanic wanted $120 dollars for that crap. I was like yeah right. It does not sound that hard! Total cost $9 dollars to do it yourself.

[@brickwal92tt]

So you only cleaned the front of the throttle body? What about the back of it, that's where the carbon gunks everything up!

[@sayuri_wrxsti]

If you want. I'm.not a tech for honda. You could remove the negative terminal You could then touch the butterfly.

[@prolly2stoned420]

I didn’t remove anything on my Chevy but the hose and I still cleaned the butterfly 🤷🏻‍♂️

[@artcore9886]

Just Go North! please tell us how you cleaned the MAS. Thanks

[@sayuri_wrxsti]

@@artcore9886 i think its lucky. What happened to me with what I did. 1. Unplug battery 2013 si navi dealer said no code needed to be pressed. 2. Unhook necessary components to access throttle body. 3. Me i pushed open the throttle plate. 4. Used wurth intake cleaner 5. Bolt everything one 6. Run like crap jump 1k to 2k. 7. Drive it hard nothing happen.. Bring home. Repeat 1. 2 step just spray outside the plate. With wurth again. And I spray directly on the mass air flow sensor Put everything back. It idle. For further cleaning. There is a intake manifold vacuum.hose. I hook it while running and quickly spray twice dont hold it Let rpm shoot up high. Check.engine light will come.on. after two shot. Plug it back or let the car stall and die. And unplug battery it turn off the cel :). And relearn the car again for 15 mins or 30 mins. After till this date from 7200 rpm was factory and I got 7400 something rpm. So extra 200 rpm. I hope it made sense.

[@TonyMontana-vw8dj]

Thanks 😊 excellent video. Changed my throttle intake hose today. Badly cracked in several places. Cleaned the throttle. Dash light goes out. Car running like new.

[@christopherhaak9824]

They all seem to crack after 10+ years, but you can get a new hose cheap.

[@LynWeeD]

Did you have the code p0171?

[@roadrunnercoyote4753]

​@@LynWeeDis that code for trouble with throttle body p0171

[@lenbata]

Just turn on ignition then have somebody step on gas pedal to the floor then the throttle will open, never open it manually 🤦‍♂️

[@ritchiedona94]

Not to manually open it is a good advice.

[@alvinlubis2226]

I thought it was recommended not to open the throttle body manually?

[@Teresag417]

Hi thanks for the video quick question at 1:14 min you mention the peace connected do you know the name of that part I need to replace it it’s broken on my car

[@musabidris7587]

Same here

[@fernandoluna7525]

Thanks to this video I was able to get my car going and make it to work on time.👍 Thank you

[@jayc3110]

Thanks... Nice informative Video. - But No link to the cleaner you used?

[@k_escobar917]

Did mine today 👍🏽just gotta do idle relearn thanks for the video very helpful

[@eddie_lo_gsr3692]

The easiest way to turn on the car on position put a brick or something heavy on the gas pedal to open the throttle body then clean it ....no need for throttle relearn if u do it that way

[@willpage79]

I got a code P0506 ..engine light off and on do you think throttle body needs cleaning..by the way since you had access already to take off the throttle body why didn't take it off completely and clean the other side better or that was enough?

[@ronking6966]

Need the name of the part at 1:20 please

[@icomba]

Try n find out wat tha part is after the maf sensor?

[@soap924]

I love My accord thank you for helping me keep her alive

[@NutzAboutBolts]

Np! Just becareful of cat thief

[@ChubbyPinoy]

Thanks you for this video. Will this fix poor or low idling?

[@NutzAboutBolts]

I would clean this and then EGR system.

[@NutzAboutBolts]

Also pcv valve, EGR system includes EGR passage and EGR valve.

[@hammar324]

That is one clean engine bay though! Good job!

[@NutzAboutBolts]

Thanks! We did an engine clean video before this video, so that’s why it looks clean. also a plus that we don’t live near the beach or anywhere near water. :)

[@Caliguy760]

@@NutzAboutBolts have you had a problem with your car shaking while at a stop in drive?

[@NutzAboutBolts]

Richard Rivera nope. I’d check for idle issues if that’s the case.

[@Caliguy760]

@@NutzAboutBolts ok what made you clean the throttle body? Was the car giving you problems?

[@NutzAboutBolts]

Richard Rivera part of a maintenance routine I usually do and recommend since over time the plate can be sticky due to carbon build up.

[@simoneware9530]

Thank you. Solved my problem ASAP!

[@flightramirez]

Does anyone know what part that is 1:23."whatever that is" may be marking code P0171 on my honda

[@flightramirez]

1:20

[@ronlam3654]

Is it drive by wire? My TSX needs the foot pedal pressed to open the throttle body

[@JohnSmith-el5mo]

Check the air intake tube, sometime it developes cracks which causes weird idling.

[@desertrider7295]

Yah....mine was cracked.

[@JohnSmith-el5mo]

Mine was under, which is hard to spot.@@desertrider7295

[@sergiosilva-xt8mh]

I want to know my accord 07 it’s accelerate and I cleaning mag sensor and throttle but no the tps this is the problem or what do you think please and thank u

[@LakayRicky]

clean as video irst after I took it for a test drive the car lack POWER, cleaned it again pulling the throttle body out of the car..... watched another video notice they mention not to touch the throttle body plate. because I might need to reset.

[@NutzAboutBolts]

You pulled the throttle body out of the engine. So you will have to do the idle relearn procedure. You can find that video in our playlist.

[@LakayRicky]

Thank you, more power to you

[@NutzAboutBolts]

No problem, also it's inline 4 cylinder so incase someone ask if your engine is V6 or inline 4 cylinder. We don't want you to get clowned on or made fun of :).

[@Zarosaki18]

Good sir does this type of throttle body have a AiCV? If there is where is it located? I need mine cleaned. Thanks.

[@normanrodrigues7887]

hey bud my eps lights turned on on my honda accord cl9 2004 some mechanics say its the alternator some say its the eps system but my alternator is kinda week at times i cant really figure out wats exactly wrong but the eps turns off n on sometimes its like it chips in n chips out just need some help

[@chriss8319]

Thanks for this video. I have a 2007 Accord just like this. I am curious does a 2007 have an Idle Air Control Valve? Does the Throttle Position Sensor ever need to be cleaned?

[@NutzAboutBolts]

+Chris S IACV is only on 03-05 year model. I think they went away with that on the 06-07 models. The 06-07 Models, they use the throttle actuator to maintain idle speed instead of the IAC valve. And the throttle position sensor only applies to 03-05 models, the 06-07 is integrated with the throttle actuator I believe.

[@terrythepion6181]

Could you please show me how to replace the rack and pinion on an 04 Honda Accord one of the boots have a whole in it

[@franciscopeirat8395]

I got an aftermarket hose, but the hole where the temp. sensor goes, it's closed! Do I need to open It, I mean, make a hole in it, right? I'm talking about the little hole on the LEFT part of the hose.

[@robertlisle9127]

I have a 2004 honda accord with p0300,p0301,p0302,p0303 and when car is warming up feels smooth but at operating temp the car shake like im in a rocket when im at a stop light. I put new spark plugs, ignition coil, and i check fuel pressure 50psi up to fuel rail. And engine compression is at 145-148 across all for cylinders. I cleaned egr ports but i did not clean throtle body or intake manifold. Will cleaning this help me?

[@kamilkhamisani8000]

hey guys. I have a Honda Accord 04 coupe 2.4L with a rattling sound coming from the hood. It's similar to putting a pebble in a soda can and shaking it. It starts at low speeds of 35+ and continues at high speeds. I've cleaned the hood, made sure everything is tight and snug. Recently got transmission fluid, new front tires, alignment and filters. Cant figure it out. Help much needed and appreciated.

[@renemoreno3194]

vaccum hose loose o broken check all hose around you see you will found also check inteck hose sometime is broken under

[@robertlisle9127]

Does is sound near the timing chain? Id so you meed new timing chain

[@danstump3686]

Check the passenger side axle vibration dampener. They come loose and start rattling on the axle shaft. Mine would start making noise at about 45 mph.

[@slozano142]

Lol that part he said what ever this is is the part I need does anyone know the name of that part I just need the black part it ripped the hose is fine

[@LakayRicky]

thanks for the video, ever since I clean the throttle body my idle is shaky and the torque on my V6 is gone.... pulls like a V4. did you reset your computer, ECU etc.

[@NutzAboutBolts]

No, we didn't have to reset te ecu. Did you happen to pull the throttle body out to clean? Or did you clean the throttle body plate like we did? We also have a idle relearn procedure video if things like that happens when you pull the TB out.

[@ulikemeb12]

Yeah, I wouldn’t have opened it. I messed up when I cleaned mine. Had to order the piece because the light came back on. Also, the car should be running when you clean it. At least when I did it. Hope this helps!!

[@staryjaszczur]

Hi there. What did you use to spray?

[@a.m-gh7876]

Hi my friend, I cleaned the throttle body and rest by scan tool but the problem after 2 days when I shift the gear to R or D the RPM low and vibration if A/C work the vibration strong, I do rest again, after 2 or 3 days the problem came again.

[@johnhiram1207]

Disconnect battery first!

[@andrewe.7907]

Good video... Got error message U0107 "Lost communication w/ Throttle Actuator Control Module" You think I need to replace the entire Throttle body.... Had the check engine light reset on car and going to see if it comes back on. Car stalled on interstate going up big hill. Thoughts? Thx.

[@robertradcliffe4223]

Andrew, did you solve your problem? Dealing with the same thing right now, same u0107 code. "D" light goes OUT as well (does not blink on and off) at times.

[@AspectExtra]

What is “that piece in the back”? Because I was driving with it not on and I didn’t know and I just want to make sure everything fine

[@smileyrod11]

CAN YOU DO A VIDEO ON HOW TO CLEAN THE MANIFOLD THANK

[@goodmandiad2713]

Look at the video on cleaning the intake runner, I found it by typing Honda CR-V IMRC replacement/ drag. P1078 P1077 2006 2.4L It s great video.

[@bobbymak6964]

Would you recommend changing the engine oil soon since the cleaning fluid cleans out the intake valves and it might get mixed with the engine oil or does it get burned off or does it have no effect?

[@NutzAboutBolts]

The cleaning fluid is too little to have any affect on the engine oil, it’ll probably be burned in the engine before it gets to the oil.

[@andreyv1]

Could you tell me what that hose is on the left side of the screen that's connected to the intake manifold? Mine is leaking and i'm not sure how to fix it.

[@rmg2344]

Please do a injen cold air intake install on this vehicle model 😊

[@NutzAboutBolts]

They only sell cold air intake for V6 engine. Short rams a waste of money lol

[@rmg2344]

Dammit

[@NutzAboutBolts]

wow, just found out they do sell them now... I guess back in the days they didn't have them. They are very expensive lol.

[@rmg2344]

NutzAboutBolts lol yea they are just food for thought tho no rush thanx for all the other great vids bro they helped me out alot over the years

[@MikeJones-jm5cs]

Toby from the office 👍 Good video.

[@ebertgermosen9700]

i got a question where its the intake air temperature sensor located at ?

[@NutzAboutBolts]

the 03-05 model has it on the throttle body housing, the 06-07 model has it integrated with the MAF sensor.

[@swong32]

my screws are in pretty bad shape - especially the screw that secures the hose clamp. any tips on getting this off if it is stripping the screw?

[@christopherhaak9824]

Use a 8, or 10 mm nut driver to remove the clamp screw, it is much easier than using the screw driver.

[@sergiosilva-xt8mh]

I have a problem I cleaning now throttled body and mag sensor but I have k&n intake. The problem it’s acceleration when I don’t do that, and ocsilated on 2000 rpm and 1500 when I on stop light

[@Loyal_Honda_Fan]

At 1:18 talk about that small thing i really have to find out what that is because i find oil in my intake hose drained from the engine via that little box, my car doesnt smoke i replaced pcv valve but still it burns oil, i have the k24a3 engine i used seafoam EVERYWHERE, i was 18 hours blasting seafoam in every hole of the car i changed x2 times oil to super clean the engine but still cant understand... 😔😢 please help me someone 😔😔😔😢

[@gunnerwagoner255]

Loyal Honda Fan purge valve ?

[@335iDom]

What is the size of the throttle body? Is it a 70mm?

[@elijahross1875]

What's the plastic tube/pipe in front of the battery

[@monkeymanx310]

why is my 2005 honda accord ex 2.4 not electronic it has a throttle cable still?

[@nandobelt8687]

@155k my check engine light came on . Thought it was the transmission would not shift pass 2500rpm. Quick trip to shop yup tps.. Well on 2007 accord TPS is built into throttle body, $950.00 to replace . They reset check engine light . Drove it 80 miles no check light 🤔 Well I had taking my car to dealer twice after 88k miles when I initially bought it used , they never did the throttle body because I cleaned it out today as per your instructions. Used 4 tough towels and they all crazy black buildup Boy what a difference. It idle at 950rpm now at 650rpm no shaking at idle when stopping . The check engine light came back on after initially cleaning and turning on engine . Is this normal , should I remove battery cables to reset?

[@nandobelt8687]

I did turn on ignition and used pedal to open up throttle butterfly not my fingers..

[@NutzAboutBolts]

Never happened to me before and I’ve cleaned many times like this. I’d get the code and see what it is, if it’s the same code for the tps, I’d bring it back to the dealership since they replaced the throttle body. Hopefully it’s still under warranty and have them service it.

[@nandobelt8687]

No I did not remove cable from negative post prior to removing intake tube and doing cleanse..

[@NutzAboutBolts]

@@nandobelt8687 its possible the throttle body detected an error while you open the throttle body plate to clean. I’d reset the check engine light and monitor it to see if it’ll come back on

[@hapetaa]

CAN YOU SHOW ME WHERE IS WIPER RELAY IN THIS ACCORD?

[@c.gdelacruz3044]

Hey I need some help over here. Ok so I did most of the steps that you've mentioned in the video except removing the intake filter's cover, I unclamped the hose to the housing instead. Getting to the issue, after cleaning it and putting the things back together, I noticed my rev goes really high when I start it say for around 2k until 3k rpm, and I also noticed that the idle stays at 1k. Lastly, downshifting of the auto tranny became jerky from 3rd to 2nd, I actually felt the deacceleration in an unusual way. Please help me out cuz I don't think it's normal for a car to do that. Plus it drinks alot of fuel now.. I have an 06 Honda Accord 2.4L i4

[@NutzAboutBolts]

+Christopher Gabriel Dela Cruz Check for air leaks, air leak will give you a higher than normal idle.

[@Mansquatchie]

Watched your video and cleaned the throttle body on my 2003 accord 2.4 today. As I opened the throttle, I noticed some coolant in the bottom of the intake plenum. Without removing the body, I just rolled up some shop towels and stuck them past the throttle plate to soak up as much as I could. Where do you think this coolant is coming from? I'm not running hot nor do I need to periodically top it off with coolant. It wasn't much coolant but it does have me concerned. Could the heater hoses to the throttle have corroded within the body and then leak into the plenum/manifold? Or should I worry about the manifold gasket. Asking you or anyone with experience on this k24A4. Thanks

[@official0227]

i think that this just means that you have a coolant leak somewhere. I'm no expert but my 07 started making boiling noises from the radiator more than it even should be and that was leading to coolant flowing to other parts of the engine. ended up being a leak in one of the hoses and a clamp fixed the problem.

[@Pexman-hu7zw]

i have exactly car like yours... doi you think it might change the tempo after u clean

[@NutzAboutBolts]

+Pex Man Tempo? once you clean it, there will be better air flow and the fuel to air ratio is better and your vehicle won't run rich to compensate for the lack of air coming into the engine.

[@tigaspinoypower]

+NutzAboutBolts Thank you very much...for replying me back...

[@NutzAboutBolts]

tigaspinoypower np!

[@FilnetMgnigon]

2005 Honda Accord 2.4L --- Does anyone know the screws and bolts for the ICV and throttle body? I heard they strip out very easy and I want to be prepared to use new screws

[@SpicyMcGeezak]

Did you figure it out? My recommendation would be to spray a little liquid wrench on them the day before attempting to remove them.

[@FilnetMgnigon]

@@SpicyMcGeezak I ended up not needing to do this. I was suffering from idle issues but was able to fix it after attempting to relearn idle procedure like a dozen times

[@baafuorawuahkofi850]

Baafuor Hi, am using a 2004 Honda Accord 2.4 and am facing a big problem nowWhenever am driving with my A/C on and I make and stop or stops in a traffic then the car beings to shake seriously but when I put it back to neural or parking it stops and the fire rises. Pls help me out quick

[@NutzAboutBolts]

+baafuor awuah kofi check your motor mounts.

[@skokomurliak]

Hello,can i use "Brake Cleaner" instead of "Throttle Body Cleaner"?

[@NutzAboutBolts]

Yes, spray it on a rag and use the rag to wipe away the carbon.

[@goodmandiad2713]

NO. Brake cleaner leaves residue.

[@almari222]

DO NOT use brake cleaner!!! Goodman is right. It leaves residue. Throttle body cleaner is different because it does not leave residue.

[@prolly2stoned420]

That screw you said is a flat head is not a flat head on mine. The part of the hose that attaches to the throttle body it’s some weird square that none of my tools fit. 😡

[@sbrave]

Just 2 sprays and that's it? Seems like you'd want to spray inside more and really clean it out?

[@nathanwright8208]

Lol

[@k.duncan5955]

Bro, Where in this specific model is the Throttle Positioning Sensor located?

[@CarlosPerez-mb1wn]

I'm looking for the Same thing If you find it lmk or send me a link if you can plZ

[@k.duncan5955]

@@CarlosPerez-mb1wn mine was on the inside of the hood, against the top right side in a little black compartment. If your car is left hand drive, it would be just behind the dash on the inside of the hood/engine bay. Some models are at the front of the engine, and others, like mine at the back of the engine bay. Hope this makes sense.

[@abdulsalamshar5601]

Hi sir, i would like an advise from you. I whant to change my 2.4 accord 2005 oem exhaust with 3.0 accord 2005 exhaust. Is it ok to do or it will harm my car. Thanks for your good work.

[@NOFLEXN912]

What's the cleaner you used?

[@NutzAboutBolts]

Throttle body cleaner, link in the description box

[@AK-pu2gm]

If viewers find that after doing this they experience high idle which doesnt disappear even after doing the idle learn:, try following these steps to do a reset and clear using the battery cable reset method: To do the battery cable reset- follow this: 1. Remove negative battery terminal. 2. Remove positive battery terminal. 3 Be sure you arent going to make contact with the battery, for later steps possibly even remove it from the car if needed 4. Connect the battery cables together either using a jumper cable or clamp them together if they reach. 5. Turn on your key to on (not ACC, to on) and yes there will be no lights on the dash. 6. Leave for 10 minutes. 7 Turn your key back to off, reconnect positive then negative and THEN follow the idle relearn procedure you will find pasted all over youtube (or just start the car rev 3k rpm until the car reaches temp and then leave it to idle 10 min). You will also need the radio code and possibly relearn your auto windows, for which there is good info for on youtube.

[@royal_await4150]

is this and an acura tsx 2006 the same or no?

[@NutzAboutBolts]

I believe so.

[@soheel88]

hi mate ive got a 2006 honda accord. it cuts of quite alot at first , say 2/3 times. and the tick over speed gets low too, any ideas

[@NutzAboutBolts]

+soheel88 confused what you're trying to ask...

[@soheel88]

+NutzAboutBolts my car cuts of like 2/3 times as I roll on.. plus the starting speed gets lower then 1 wen I put in gear which eventually engine cuts off

[@NutzAboutBolts]

soheel88 are you driving a stick shift? sounds like your clutch isn't engaging or your vehicle lacks air into the engine when stepping on the gas.

[@soheel88]

+NutzAboutBolts stick shift?? any ideas to fix the problem.. you reckon I should try this throttle body clean

[@soheel88]

+NutzAboutBolts it runs fine once started moving. just cuts of twice.. after that it drives

[@naimrf]

Will it remove error code p0123

[@vioera1]

What does it mean when my IMA light come on I have a 2007 Honda accord hybrid

[@NutzAboutBolts]

seems like it has to do with your hybrid battery.

[@goodmandiad2713]

It means your battery (anywhere from $1400-$200.00 if you do research and do it yourself.

[@grime4653]

good vid but u shouldn't spray into it spray the rag and those rags r not good for throttles leaves small red hairs

[@NutzAboutBolts]

yup, we read it online as well and we noticed it on some cars, but our rags barely have lint on them. I think it might be certain rags that have a lot of lint, ours don't have any or you can barely see them.

[@afterdark6822]

Noticed a difference between throttle body sizes between usdm, jdm.

[@bm0n3ybmg77]

is this the same way to change it on a 02 accord

[@NutzAboutBolts]

+Robert Jenkins what is the same? cleaning the throttle body?

[@bm0n3ybmg77]

Yea. You would do the same steps if you were to replace the assembly wouldn't you?

[@NutzAboutBolts]

+Robert Jenkins they're both different engine. The process of it is the same concept but removing it is different.

[@sagarswan2011]

Hey I was wondering if you can possibly help me out. I have a 06 accord and when I put it in drive(standing, not moving) it makes this rattle noise. When I take my foot off the brakes and give it gas, its fine after that but when I come to a light or whenever i come to a stop(still in drive) it rattles. Any ideas from your experience?

[@NutzAboutBolts]

+Sagar Swan something could be loose that's making the noise cause by the engine vibration from the idle. If there's no check engine light or performance issue, then that's what I would suspect. I've never experience that before besides the noise from the glove box... which the foam is worn out over time.

[@sagarswan2011]

+NutzAboutBolts ill check that out, could be something loose around the idle. There are no check engine light and only has 46k miles but ill keep looking. Thanks man, appreciate it

[@tele3phono]

i was having that kind of the same issue. turned out to be low oil (oil level was not low enough to turn the low oil light on). this accord generation is known to build up carbon on the piston rings and subsequently burn oil. my vehicle was burning about 1.2 qt per 1000 miles. engine was rebuilt under Honda's warranty at no cost. just paid for an oil change in order for Honda to determine how much oil it was burning

[@tele3phono]

+Andres Leon btw, Honda wont rebuild the engine unless it is burning more that 1 qt per 1000 miles which they say it is "normal" and your vehicle is still in warranty

[@NutzAboutBolts]

Andres Leon burning 1 quart every 1k miles is insane since the oil pan only holds 4.3 quarts... I would suspect just a bad engine. Luckily my vehicle hasn't been burning any oil or I haven't noticed any oil consumption... sucks that you had that problem, these vehicles are very reliable and shouldn't be doing that, glad you got it fix under warranty. Thanks for the info and I appreciate letting others know of similar problems as well.

[@MohammedElSanousi]

HI I got an issue today on my 2005 i4 Accord .. my rpm suddenly went on 4000 rpm ,, I was just setting on the car not moving ... do you think I need to clean the throttle?? thanks 😄

[@NutzAboutBolts]

sounds like you have a huge vacuum leak somewhere to have that high of a rpm.

[@rhdtv2002]

I thought that if you open and cleaned the throttle without completely removing it that it would easily damage.

[@NutzAboutBolts]

+Rich Lo Not that we are aware of, and we've been doing this many times.

[@rhdtv2002]

+NutzAboutBolts is this a electronic throttle. Those are the ones I heard to remove completely the clean and out back.

[@NutzAboutBolts]

+Rich Lo Yeah, you can remove it, and then reset it back to idle learn procedure. But we haven't tried that before and thought this was easier to clean.

[@tigaspinoypower]

+NutzAboutBolts what do you mean by reset idle learn? how do you do that sir!

[@aymannabil3044]

What is the small hose in the front of the intake manifold?

[@saginaw60]

Ya say Phillips screwdriver? Ever hear of JIS? Japan Industry Standard looks like Phillips but is different much plenty.

[@Bigbird845]

Oil change man , next vid what you think?i always wanted to know how to do that and thanx for that i bought 2006 honda accord but with 193.376 miles on it im clean that throttle lmfao!! But yeah thanx for Ur vids man

[@NutzAboutBolts]

+eric nieto we already have an oil change video, unless you mean something else?

[@SXFVE]

my air bag light just came on in my 2003 Accord. Am I in danger??

[@NutzAboutBolts]

I would take it to the dealership to have them diagnose it, you don't want the air bag to accidentally deploy since the light is on.

[@davidsteadyjr8243]

S1X F1VE air bag won't accidentally deploy lol only issue would be what ever fault it is for what air bag it May not go off. It won't deploy

[@pole_barn_builder]

S1X F1VE Nope, replace your driver's side seat buckle latch!

[@mhow7024]

there is a recall notice for my 04 accord for air bag. i think the same applies to you. so check on that and take it to the dealership. the replacement is free of charge

[@craigfeldspar2740]

imadvizinyounow it works? I have the same problem on my accord 2003

[@dbleezy805]

Nice shirt lol I see those Rasta colors!!

[@pilot2020]

I did this and touched the butterfly and had high idle after on my 08 crv had to go to friends shop and had to plug in the scan tool to go do the idle relearn because on 08 and up the steps for doing the relearn doesnt work it needs a scan tool so dont touch the butterfly the auto relearn wont work

[@oludashesamuel2850]

I hope this works for me

[@realtruth97]

You gotta take off the entire throttle body in order to clean it the right way bro. I just did that yesterday

[@SpicyMcGeezak]

Can you clean it good without moving the plate? What’s the best method after reinstall?

[@anyman6009]

Hello its me again, where can i find the sensor for P0135 honda accord 2005 2.4? Thanks

[@NutzAboutBolts]

it is the air fuel ratio sensor, its the sensor right after the exhaust and before the cat.

[@anyman6009]

So the same sensor to be change when u have a po157 right upstream?

[@frostbyte2153]

Is this a thing?

[@jennishagomes9790]

can this trigger the engine check light to stay on

[@NutzAboutBolts]

If you spray too much of the brake clean fluid, it can cause the engine to run rich, which can trigger the check engine light. We just spray if on the rag and wipe the throttle plate to clean it.

[@abubakarsadiq1248]

Great to see and learn from you.. MNY TNX

[@hasnatarshad7283]

Firstly why you not disconnected a battery wire?????

[@Danimaljmartin]

I see where he is trying to good. But first he has no clue you don't use shop rags to clean anything leading into the internal engine second never push open an electronically controlled throttle body Doing so can throw off its calibration causing sparatic idle loss of fuel mileage or cause damage to the internal components of the throttle body just to fill you on what that tube was that you said you didnt know its a ctsnke vase vent hose the square block that pushes into the intake hose is a filter you can solve all these problems by proper maintenance meaning chainging the Franke vase vent filter when you do tune ups assuming you take care of you vehical at all and remove the neg terminal before unplugging anything electrical that's just rule of thumb when doing any thing under the hood

[@thomassantorelli787]

and so if you push open the throttle plate and you get a code for the plate, what's the fix? It's been relearned and runs great except for the code.

[@mikeboudissa885]

OCD

[@permanadanwaktu7778]

When i saw you touched that butterfly.., i knew that you are not doing it very often

[@abdulloisaakoff870]

This video putting me to sleep

[@rmg2344]

Or short ram

[@jeffscomp]

Should've cleaned it more with the spray.

[@NutzAboutBolts]

+jeffscomp It was cleaner than usual, but if it was dark, we would've used more spray. :)

[@ivelisseivelisse5503]

Yo pensaba que se descontralaba si se acia de esta manera 🤔

[@raulhondaaccord2596]

Tengo la misma duda ya que es electrónico

[@BattlefrontZero]

I think 2003-2005 Accords actually have a throttle cable.

[@NutzAboutBolts]

yeah they do, its the same concept. Its a lot easier cleaning the throttle plate with the cable since you can manually move the plate back and forth to open and to clean it.

[@lancewilliams949]

My 2005 doesn't have a throttle cable, it's electronic.

[@DPNY-qm4ix]

I have an 03 exl v6 with no gables. All electronic. I took the whole TB out and cleaned as well as the IAVC, I had a code P0506, which caused me to clean both extremely well..

[@JaimeGarcia-vd8tb]

Wow!

[@hayelgaraibeh7906]

NEVER CLEAN THE THROTTLE WHILE THE BATTREY IS CONNECTED. YOU MIGHT CUT YOUR FINGERS.

[@markantonicasarez9834]

Pork mi carro camina un rrato y seme apaga es honda accord 2003

[@luismacros]

Talvez se desprogramo el cuerponde aceleración