2005-2010 Chevy Cobalt Engine Removal

We will be pulling this engine out of a 2008 Chevy Cobalt to rebuild it.
😎If this video has been helpful consider supporting us with a cup of coffee! 🙂
www.buymeacoff...
🛒PARTS LIST:
➦ Piston kit with rings: amzn.to/48P05hi
➦ Rod bearings: amzn.to/3Si0TUZ
➦ Crank main bearings: amzn.to/3Ugn1Bp
➦ Lower gasket set: FEL-PRO CS262231 (currently not available on Amazon)
➦ RTV sealant: amzn.to/3U9TYj8
➦ Assembly lube: amzn.to/3ua1pMD
➦ Timing kit: amzn.to/3HyKHJN
➦ Water pump: amzn.to/3UcAPNz
➦ Head gasket set: amzn.to/3ujd37P
➦ Head bolts: amzn.to/3HzbQMJ
➦ Coolant: amzn.to/3SiIAyT
➦ Break in oil: amzn.to/3Ubxcr6
🛒TOOLS:
➦ Piston ring compressor: amzn.to/3Sbfq4G
➦ Valve spring tool: amzn.to/3Z557Bm
➦ Pick set: amzn.to/3u9AdNZ
➦ Torque wrench 3/8: amzn.to/3SuqHN6
➦ Torque wrench 1/4: amzn.to/3Z3k8n5
➦ Torque wrench 1/2: amzn.to/3AgaOB2
➦ Ratchet and wrench set: amzn.to/4b6K8ob
➦ Impact socket set: amzn.to/3Hy3fKi
➦ 32mm socket: amzn.to/3Z7x8Iv
➡️I am part of the Amazon affiliate program and get a small commission when purchases are made through the links provided.
🔺DISCLAIMER
The information provided by Valley Mobile Automotive (“we,” “us” or “our”) on this video is for general informational purposes and entertainment only and does not replace professional advice.
All information is provided in good faith; however, we make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability or completeness of any information on the video.
By working on your own vehicle, you take responsibility for the outcome.
Under no circumstance shall we have any liability to you for any loss or damage of any kind incurred as a result of the use or reliance on any information provided on this channel. Your reliance on any information on the videos on this channel is solely at your own risk.
----------------------------------------------------------------------------------------------------------------
Thank you for watching this video, click the "SUBSCRIBE" button to stay connected with this channel.
🌟 Subscription Link: cutt.ly/YTtPqv4

[@thebeez9487]

3/8 fuel line disconnect tool and there's 9 bolts that bolt the engine and tranny together. You're welcome.

[@dws2313]

Looking forward to the next video!

[@ValleyMobileAutomotive]

Thanks DWS! This was a fun project 🙂

[@Mr2004MCSS]

Nice video. My daughter owns a 2010 Cobalt with this engine. Luckily it still runs good with about 135,000 miles on it. A shift solenoid in the transmission went out at the end of last year but she had it fixed. That job was more than I wanted to attempt so she had to take it somewhere for that repair.

[@JCGible]

Now, why can't I separate the engine from the bellhousing. Yours just slipped out.😡

[@ValleyMobileAutomotive]

Double check that you got all the bolts. There are at least two that are easily missed. Sometimes the two dowels that line up the tranny can be stuck and just need some persuasion.

[@JCGible]

@ValleyMobileAutomotive I missed the two lower motor to transmission mount. Had to jack the car back up to get them. Thanks for the videos 😊

[@ValleyMobileAutomotive]

@@JCGible Sweet! Glad you got it 👍

[@clarktolson7001]

How many bolts are there??

[@skyknightking0]

I want to replace my 2.2 L in my 06 Chevy cobalt LS 5spd but it's becoming a hassle trying to figure out which cobalts I can get the engine from and my coil pack is all-in-one so I don't know if that makes a difference and I don't know if it makes a difference if the engine comes with a automatic transmission I would think I could just take off the automatic parts and I could just bolt up my transmission if you can give me some tips it would be much appreciated because I'm going to have to go that rebuild route and just get a part one at a time and put together the engine before something else happens

[@willischristmasshowwillis7362]

Great video as I will be tearing down a 2.2 Ecotec. What was the tool you used to decouple the fuel line from the rail?

[@nathandeetz6557]

Fuel line wrench. It's a 3/8

[@estlhm805]

Everything you forgot to remove I had to do the same thing.😂😂😂

[@edwardotorres8183]

@valleymoblieautomotive for the final bell housing bolt behind the exhaust, how would you recommend removing the bolt it the bolt strips, could I use a it’s extraction socket to remove the bolt? 12:45

[@DefundtheIRS1776]

I rounded that bolt because of the extreme angle. Curious if anyone figured it out

[@mistermetalman]

Did you evacuate the refrigerant before removing the compressor?

[@ValleyMobileAutomotive]

Fortunately It's not needed. The lines can stay attached to the compressor 👍

[@mistermetalman]

@@ValleyMobileAutomotive nice!

[@luciangelone]

I have to take a decision in the next three days...I have a 2010 Chevrolet Colbat, the motor is finished and my garage suggested to replace it with a used motor which he claims has a 72000 km...the garage guaranteed the motor for 6 months...I am a little bit scared about the 72000 km motor we have no life span of this motor...the job asked 2300$ +taxes... CAN YOU PLEASE GIVE ME YOUR OPINION IF I DECIDE TO REPLACE THE MOTOR IS THERE A CHANCE THAT IT MIGHT NOT WORK? WHAT IS YOUR OPINION PLEASE THIS WOULD HELP ME A LOT MAKING THE DEVISION... WOULD YOU GO ALONG REPLACING THE MOTOR OR NOT? WOULD YOU THAT STEP? SI CE YOU ARE A GOOD MECHANIC ? thank you very much for your help and hope to hear from you soon witho the next three days...God bless

[@ValleyMobileAutomotive]

@@luciangelone $2,300 seems like a good deal. I would ask a few questions like do they guarantee it will run after installation? If it doesn't run do you still have to pay them labor anyway? What does the warranty cover? Make sure everything is in writing. Also how is the rest of the vehicle? Body, suspension, transmission etc... you'd hate to put in a new engine if the rest of the car is falling a part.

[@nicolecook2024]

Now that it has been a year since you have apparently removed the engine, was it worth it? I have a 2008, looks similar year, it is having engine problems, would you recommend, did it last a year?

[@ValleyMobileAutomotive]

This car is still running great! Rebuilding engines is fun but a lot of work. If you plan on keeping the car for a while it may be worth rebuilding but if you're not sure then just doing an engine swap with a known good used engine may be a better choice.

[@johnnybotz]

Not A huge order of removing things Your hilarious.... Id bet that screwdriver with the fork on itlol(fatener remover is prolly in the last engine you rebuilt

[@kirklandhannah3401]

Where is the VVT silonoids?

[@ValleyMobileAutomotive]

This engine did not have variable valve timing.

[@kirklandhannah3401]

@@ValleyMobileAutomotive thank you very much for the response!

[@Mr2004MCSS]

@@kirklandhannah3401 I was wondering the same thing. My daughter's 2010 Cobalt with this engine has them. I guess I thought that they all had them.