2005-2010 Chevy Cobalt Engine Installation

Finally this engine is being reinstalled in this 2008 Chevy Cobalt!
😎If this video has been helpful consider supporting us with a cup of coffee! 🙂
www.buymeacoff...
🛒PARTS LIST:
➦ Piston kit with rings: amzn.to/48P05hi
➦ Rod bearings: amzn.to/3Si0TUZ
➦ Crank main bearings: amzn.to/3Ugn1Bp
➦ Lower gasket set: FEL-PRO CS262231 (currently not available on Amazon)
➦ RTV sealant: amzn.to/3U9TYj8
➦ Assembly lube: amzn.to/3ua1pMD
➦ Timing kit: amzn.to/3HyKHJN
➦ Water pump: amzn.to/3UcAPNz
➦ Head gasket set: amzn.to/3ujd37P
➦ Head bolts: amzn.to/3HzbQMJ
➦ Coolant: amzn.to/3SiIAyT
➦ Break in oil: amzn.to/3Ubxcr6
🛒TOOLS:
➦ Piston ring compressor: amzn.to/3Sbfq4G
➦ Valve spring tool: amzn.to/3Z557Bm
➦ Pick set: amzn.to/3u9AdNZ
➦ Torque wrench 3/8: amzn.to/3SuqHN6
➦ Torque wrench 1/4: amzn.to/3Z3k8n5
➦ Torque wrench 1/2: amzn.to/3AgaOB2
➦ Ratchet and wrench set: amzn.to/4b6K8ob
➦ Impact socket set: amzn.to/3Hy3fKi
➦ 32mm socket: amzn.to/3Z7x8Iv
➡️I am part of the Amazon affiliate program and get a small commission when purchases are made through the links provided.
🔺DISCLAIMER
The information provided by Valley Mobile Automotive (“we,” “us” or “our”) on this video is for general informational purposes and entertainment only and does not replace professional advice.
All information is provided in good faith; however, we make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability or completeness of any information on the video.
By working on your own vehicle, you take responsibility for the outcome.
Under no circumstance shall we have any liability to you for any loss or damage of any kind incurred as a result of the use or reliance on any information provided on this channel. Your reliance on any information on the videos on this channel is solely at your own risk.
----------------------------------------------------------------------------------------------------------------
Thank you for watching this video, click the "SUBSCRIBE" button to stay connected with this channel.
🌟 Subscription Link: cutt.ly/YTtPqv4

[@alexgonzalez2338]

Thank you very much for your videos, my son’s car engine failed and we replaced it with no issues thanks to you ! Appreciate all the help!!

[@ValleyMobileAutomotive]

Awesome! Glad this video was helpful 👍

[@JRobert111111]

You're a brave soul working on that small front wheel drive vehicle. I'll stick to my V8 rear wheel drive where things are much easier to access. That head gasket "blows", having to do that over again; but FelPro is the only brand I'll consider other than OEM. That was a very good tip on die-electric grease on the hoses, I've never thought of that. Also, very good idea using anti-seize on the exhaust bolts, which I have always done. Great job, and I thoroughly enjoyed this series you did on this engine.

[@ValleyMobileAutomotive]

The head gasket fiasco was terrible! I learned a huge lesson. Fortunately this is my own vehicle and not a customer's. Thanks for watching the whole series 🙂

[@modquad18]

Really appreciate this series! Getting ready to swap a 2.2 in an ‘08 that my son ran low on oil. Found a new GM long-block for $1450 and hoping to get ‘er done this week. Your vids will really help 👍🏽

[@ValleyMobileAutomotive]

Great! It should be a pretty easy swap. If you have any questions feel free to shoot them in the comments 👍

[@modquad18]

@@ValleyMobileAutomotive Thanks!

[@haniballecter7605]

You did a great job 👍

[@johnharty5757]

Great video I do disagree though about why the 2000 to 2500 some would say 3000 RPM break in for 20 minutes this was originally done with cam in block flat tapet engines and was to splash the cam lobes with oil as the only lubrication the lobes get in a cam in block engine is slash from the rods and the splash patern changes between 2000 and 3000 thus the reason for the variance in rpm to make sure all lobes are covered thiis is the same reason some have said to vary highway speed driving for the first 500 miles In my opinoon still not a bad idea to perform this initial break in however the highway miles I would do some full throttle to the rev limit pulls as this is the best way to break in rings wich unfortunately us flat tapet cam fans cant exercise unless we want to chance wiping a cam lobe

[@chrisalsup3912]

Hi I have a ‘06 cobalt and it’s a 5-speed and the throw out bearing started making a-lot of noise. My question for you is would it be easier to pull the engine or transmission? Unfortunately I don’t have access to a car lift….

[@andrewsmith7445]

But that head gasket thing is hilarious. 😂 I know how you feel, where you just sit in the car and look out the window.

[@andrewsmith7445]

That's the trouble with getting a motor rebuilt. I definitely think mechanics would have more work if it was video documented because I definitely want that motor knowing how well it's been rebuilt.

[@advancedleveldiagnostics]

Nice series, Thanks!

[@ValleyMobileAutomotive]

You're welcome! Glad you liked them 👍. Rebuilding engines is a relaxing experience... Until something goes wrong lol 😂

[@adamgonzalez4393]

Awesome job on everything you did in your videos on the Chevy colbalt how much do you charge to do mine? I need someone like you that has very good experience with working on a Chevy colbalt.

[@warrenbenson7970]

Where does that first ground wire run to?

[@MeaHeaR]

I Noticé this particular Veee-Hikull has No A/C Kompressor or Any Alternator. Was this Omitted for thiss Veee-Hikulls ????

[@ValleyMobileAutomotive]

This has both alternator and AC compressor. 9:38 has the torque specs 👍

[@MeaHeaR]

@@ValleyMobileAutomotive oh thanks I need to change my ac compressor und was looking forward for you to show how it done 🤔 Alas No 😞 😢 😔

[@ValleyMobileAutomotive]

@@MeaHeaR Oh I see. I don't know if there is enough information between the engine removal video and this one. Sorry

[@charlesroybal4764]

In your experience is a Chevy cobalt LS 2006 a decent car?

[@ValleyMobileAutomotive]

I think they are great little commuter cars. The biggest issue I see with these is that they lose oil in between oil changes. Because of this it is easy to run them out of oil. That's what happened to this car. You need to be good at checking your fluid levels regularly.

[@johnharty5757]

​@ValleyMobileAutomotive Agree completely people ask me if the 2.2 Ecotec (l61) is a good engine and I say well they consume a little oil and they will not tolerate dirty oil as the timing chain tensioner will plug and fail Keep clean oil in them and don't let it run low and they will last a very long time Currently driving a 2005 cavalier with the l61 with 262000 miles on it and still healthy This is my fourth l61 and highest mile l61 unfortunately I have not been able to find out just how many miles one can get out of one because the other three were wrecked two of them due to loaning out and one of them my was my bad pulled out and missed seeing a car

[@modquad18]

I really like the Cobalts. Bought my son a 2008 new and just now getting ready to swap the engine as he let it run low on oil and it jumped time. Before the motor swap, I renewed all of the suspension and the lower steering shaft and it was super easy. Great, easy to work on vehicle in my opinion. Decent fuel economy too!

[@ceballosmarcos1]

Where do you purchase an engine for a cobalt?

[@BobSwagget]

where are you located? id like to have my 2005 chevy cobalt engine checked out and repaired if possiable!

[@JayLo413]

2 torque bolts by the cam sprockets weren't installed.

[@behnammohajeri7047]

Hey you're talking too much