2006-2010 Ford Explorer ABS Light Tone Ring Failures

[@chuckmike]

Did 2 tone rings today on my 06 explorer. Without this video, I would have never gotten them done, let alone both back rings in 1 day....Thank you so much for the information....

[@FordTechMakuloco]

Good to hear!

[@melwilliams6485]

What is the proper name for the compression tool to position the ring?

[@chuckmike]

I used a piece of steel pipe and a heavy hammer

[@nathankaradimos8338]

Helpful video, just did this on my 2006 Ford Explorer. Took me much longer than I hoped. Be prepared for the 3 screws on the inside of the wheel. They're extremely difficult to reach and basically cemented on. I spent 2-3 hours alone on those and even used an impact gun with a U-joint. I had to use a breaker bar on 2 of them at different points and put all of my strength into it a dozen times. Not sure I would do this again :)

[@nathankaradimos8338]

But my traction control light and ABS are both gone - this was also giving me transmission problems with a really really rough shift that appear to be resolved.

[@brianreed5686]

Some times the ring will move to one side. I have done a couple that somehow shifted out of perfect alignment. Used a punch to gently put it back in alignment with the sensor and it was good to go. Some will even work when cracked. The crack let's it open and shift position so the sensor doesn't read the ring. Try to put it back in place and Use a dab of epoxy to hold in place. (For emergency repair only)

[@robertrenton8898]

Thank you very much . Just bought my 2008 explorer mint condition couldn't figure it out.

[@lorijackson9208]

Thanks for the informative vids. The first "expert" I've seen who doesn't direct ABS problems to the rear end sensor (That never seems to solve the issue) I think my 2003 F150 might need this repair, but it looks like a different set-up. Internal ring maybe? Would the repair be similar? Thanks again.

[@Kinghoot1974]

I just want to Thank You your videos have helped save my family a lot of money they are step by step and extremely thorough. Question if you have the time , I recently purchased a 2007 expedition limited that had rear air ride. I just put in Arnott strut conversion and didn't get a chance to put the bypass switch in yet. But today a steady traction control light and abs came on. Can that occur because that bypass switch isn't installed yet,or could that be the tone ring and if so would it show up in freeze data on scan tool. Thanks again

[@quartermilelife1568]

thanks alot i got rsc now and truck wont start i did the front hubs they were old anyways, still wont start, this is all after son caught some air driving thru a roundabout at 50mph. so would the tone rings in the rear cause the car not to start?

[@coachmac9029]

Replacing the ABS Rear Center Speed Sensor on my 2005 Explorer with AdvTrac I was able to locate the bolt on top of the differential as described. However there is no connector and no sensor anywhere to be found. Instead the bolt seems to be holding some sort of plastic plug instead of the sensor. Is it possible there was a manufacturers modification eliminating the rear center ABS wheel sensor? Any feedback from subscribers also welcome. Thanks. Coach Mac

[@josephklapiszewski6114]

Great video, as always. Didn’t see one for an expedition. I have 07 Expy with a C1236 code (and both ABS and traction control lights on). Replaced the sensor, reset and it lights came back on? At low speeds the lights will go off but once I get moving they come back on. Could it be a tone ring issue too? It’s the driver side rear wheel. Thanks!! Joe

[@JerryB67]

i have a 2007 ford explorer and the abs and traction control light keep coming on , but there are no codes . checked both speed rings in back ( 2wd ) they are both tight and didnt see any cracks , any idea what it might be ?

[@nomation]

I'm receiving the C1236 Code for the front right side. Do you have a video showing how to replace the Tone Ring for the front axels?

[@robbierob123654]

Love how it's Chevy commercials and your a Ford guy... Too funny..

[@FordTechMakuloco]

I know I saw that too, but hey what are you gonna do.

[@RMyly]

Was hoping this would be less work.....How many labour/hrs does dealer charge for 1 ring. Want to figure out IF it is worth it for me. You're the BEST btw!

[@eegg6954]

$2755 replace tone ring in New York/Long Island at dealer.

[@robbierob123654]

2For 2.....rad now tonner ring...... Thank you Sooooo much... I followed u to the tee, works out great..... THANK YOU SOOOOO MUCH!,!

[@FordTechMakuloco]

Good to hear!

[@Wagohowardhanahou]

I’ve got a 2005 that used 2006 wheel hub assembly I’m replacing right now. I am getting the ABS LIGHT and feeling the advanced track go on and then off.. thusly throwing off the 4x4 high low and all.... so SAME ISSUES. Problem is I don’t have power going up a small incline and probably not towing... Question- when I replace the rear hub I hope to fix the issue... how hard is replacing the tone ring.. does it matter the year 2005-2006 for ring ?

[@steviem5279]

The 06 Escape/Mariner has a similar problem but with the tone rings on the front, what will end up happening is the 4x4 light will flash eight times and the ABS light comes on and most of the times its a cracked and loose tone ring. What I am wondering is when you replace it, it better to just replace the entire axle or just to tone ring is enough?

[@aljack9924]

Also Brian can i disable the sensor for now???

[@alansmith9174]

I have a 2004 taurus that the abs and brake light comes on at random. Code b1342-20. I replaced the abs module and it still has the lights coming on, what else could it be?

[@6514284531]

I have a 2010 ford e350. The dash screen will say service advanced traction control. And the swerve tires dummy light comes on. But then they both turn off. This doesn't happen ever day driving. But when lights turn on, they will do it many times in a row intermittently. Sometimes it seems like a loose wire just disconnecting and reconnecting, but then one time while cleaning van out, it did it..... So that's where I am.

[@razr199]

Thanks for the video bud. I have a 04 Explorer. Pretty sure mine just cracked.

[@joeserencsics1052]

Why remove the caliper, can't that stay attached while lifting it out of the way. Is it too much pressure on the brake line?

[@tonylorenz9853]

What is the part number of the ford service tool for the ring install? Or what did you use instead?

[@FordTechMakuloco]

Tony Lorenz The Ford tool number is from like 1978 just use a little heat and tap it on as shown in my other videos. An oven to heat the ring evenly is a good idea also.

[@1micYT]

I think I am having this problem with my 2006 Explorer right now. ABS, traction and wrench light on.

[@xXBEERCULESXx]

What did your problem end up being because I have an 08' that's doing the same thing?

[@draftking77312]

But does this problem cause your battery to drain Maddie out while driving ?

[@n310ea]

Do customers ever take their Ford/Lincoln/Mercury vehicles to you for strut replacement? I'd love to see a strut replacement video.

[@FordTechMakuloco]

No not really a few here and there. The struts don't fail too often.

[@onemale70]

Thank you for this video, that is the exact same problem I'm having. I will head out there today to try and repair it once I order the tone ring. Do you think anyone rents that ailment tool for the tone ring installation?

[@FordTechMakuloco]

onemale70 Not likely, but you may be able to find something similar once you have the new ring in hand.

[@itslocal8716]

Could this be the cause of my rsc sensor popping up

[@johnfabian4936]

Great video with step by step instructions to replace the tone ring on an Explorer! Any additional tips or tricks on how to remove the 3 bolts that hold the knuckle to the trailing arm? It's pretty tight getting a socket in on the bolt head closest to the lower control arm and I'm guessing you would need to use an extension, thoughts?

[@FordTechMakuloco]

John Fabian Yes you will need an extension, I show all the tricks to get to and align each bolt.

[@manny3164]

my ford expedition advanced track system came on. also it says to check it. the awd 4x4 dont work at all, do you have any clue what might causing it?

[@FordTechMakuloco]

+manny3164 The code will tell you what is causing the system to shut down.

[@manny3164]

thank you for the response. i took it in and they said the sensor had to be reatored by a ford dealer...

[@melina3213]

.

[@onlywenilaugh6589]

My 2005 Front tone ring cracked. Had to replace it due to rust build up under it.

[@aljack9924]

Hi Brian, I am getting a similar problem with my 2005 explorer whoever I can not move the car and the 4X4 high keeps activating and the abs as well. it feels as though it is coming from the front because I hear a bit of a grinding noise. What could it be. Need your help thanks

[@FordTechMakuloco]

I would jack up the fronts and check the bearing to see if they are loose causing erratic abs signal. You can disable abs by pulling fuse 5 and 10 from engine fuse box and fuse 22 from the interior fuse box.

[@aljack9924]

Thank you so much you are the best I fixed my temperature control switch watching your video. Where are you located?

[@FordTechMakuloco]

Chicagoland area.

[@aljack9924]

I removed the fuses and the truck is running normal what do you think? Is it the sensor or the tone ring. I did have the bearings change once before. Sorry for all the questions but you seem to want to help us every day guys. I can not thank you enough.

[@FordTechMakuloco]

An 05 was more common for the rear abs sensor in the diff but it sounds like yours has RSC and should have these tone rings on the rear anyway. Anyway like I showed in the video inspect the rear rings for cracks or looseness and you will need a scan tool to check for codes and most likely the tone ring pattern as shown in the video if not visually evident.

[@zacchop9997]

Is it bad to keep driving with it on?!?!

[@tamyboy1]

Great video!

[@llopezlapl]

Hi, i have a 2006 ford-explorer im having a lot problems with it, all the lights on the dashboard come out very often, and then lately the check charging system turns on as well do you have any idea what it could be ?

[@FordTechMakuloco]

certainly sounds like either a cluster or alternator problem. I would check the alternator first.

[@pasleyford1437]

All these videos are for the rear are there tone rings on the front

[@KevinCumberton]

would this apply to a 2012 as well?

[@Mustangmike232]

If you don’t have that tool to press it on don’t bother! I tried heating it up and everything, no use, going to ford now

[@emehlig7842]

Great video ! Really appreciate the torque Specs !!

[@dukeman7595]

Weld it and forget it!

[@FordTechMakuloco]

um no

[@grantsimko]

What is the software you are using in the video?

[@FordTechMakuloco]

Grant Simko Ford scan tool called IDS.

[@grantsimko]

I had the wrench, abs, and traction control icon all come on at the same time (06 explorer advance trac). I haven't had a chance to investigate rings yet...if no damage is visible what do you recommend?

[@grantsimko]

I just looked at both rears and neither is loose or broken, but the right rear is full of dirt and rust. Can that cause a problem? Is it ever the fronts?

[@grantsimko]

I couldn't even see any in the front. Well, thank you for the help, i appreciate it!

[@FordTechMakuloco]

The fronts almost never fail the mud will cause an issue yes.

[@nemss11]

Is that important to change??

[@keilatravels1790]

hi...what do you mean when you talk about foot pounds? thanks

[@FordTechMakuloco]

+Ulises Salazar That is a measurement of torque applied to a nut or bolt.

[@keilatravels1790]

+FordTechMakuloco thank you! Mechanic told me the whole axle needs replacement because of ring. ordering the ring from your link....thank again

[@Goodpatron]

Video starts at 4:15. Thank me later.

[@frankmc5112]

Great video but it's cheaper to buy a new axle than it is to get that fuckin' tone ring tool.

[@MartinRodriguez-gx9cs]

Need help! I have a 2010 Ford Explorer, that started to stall when I would make a right turn. Yesterday I was driving it and it and the truck just kept stalling like the abs or traction control kicked on. Weather condition was sunny with 70 degrees out. Once I pulled over the traction control light and the 4x4 came on. I turned both switches off and the truck continued to drive but with the stalling. I removed the abs and the 4x4 fuses and I was able to drive it home with no problem. I installed the fuses back and the issue started all over again. I checked the tone rings and they seem to be fine. Is there anything I should be checking. If anyone can help I'd really appreciate it!!!

[@blueeyedbb7777]

Hey did you ever figure out this problem sounds like what in going through now.. thank you in advance

[@alvinsingh7842]

Have you guys ever fixed this??

[@MartinRodriguez-gx9cs]

It turned out to b one of my wheel hubs. The way I checked it I lifted the front end and I grabbed the front wheel while it’s in the air top and bottom then tried shaking the tire. There was a little play on my driver’s side so I figured that was the bad one. I ordered both hubs with the abs sensor and I started with the one I thought was bad. Once I replaced it the problem went away, then I proceeded to change the other side. If ur truck is stuck somewhere with the issue I had. The way I got it home was by removing all of the abs fuses. All the lights on the dash came on but the truck drove home with no issue. Hope this helps, good luck and let me know if u have any other questions!

[@eegg6954]

@@MartinRodriguez-gx9cs Thanks for sharing that! You saved my day.

[@MartinRodriguez-gx9cs]

No problem, glad I could help!

[@tomascharles5080]

That's a lot of work for a tone ring.

[@Benbenford]

Good work

[@nataliegarcia3915]

what is the replacement ring Things ñame

[@FordTechMakuloco]

+Esperanza Garciakj Tone ring link is in the description.

[@cj10211982]

WHAT ABOUT 917-532?

[@WILSON.1]

203 ft lbs holy cow!

[@WILSON.1]

260, also, wow!

[@pito4141]

I live in the Chicago area and I would like to know how much would you charge me to do this same job on a ford escape 2001 v6?

[@FordTechMakuloco]

I don't do side work unfortunately.

[@TheKing-nu4fk]

@@FordTechMakuloco I gaurantee you get tired of telling people this over and over and over