2006-2010 Jeep Commander/Dodge Dakota/Durango/Aspen AC compressor (4.7L V8 engine)

[@vicky20477]

Thanks! Was able to replace a/c compressor with your directions.

[@lestergill9877]

Good work and directions of removal a/c compressor.

[@patrickkirby7612]

A shop in Nashville installed a new compressor it took 3 guys, 2 hours non stop, THEN they said the new one was bad, and got another, THEN they ciuldnt get it to be cold so whats the problem? Day 2 now. What could be the issue????

[@HelpingHandAutoRepair]

Not sure but please find a new shop. Those guys clearly don’t know what they’re doing.

[@johnfritz3792]

I have a 2008 with the 4.7

[@damanimcclain2065]

Was this a compressor only change and if so is it still running strong. Pep boys says if I don’t replace it all I’ll have to do it again in a few short months and I’d be fine with a few months because it’s summer here in az and it’s 117 today

[@HelpingHandAutoRepair]

Just compressor. Have an ac shop vacuum out the system for 15-20 mins and then charge it to the correct level. Please don’t use that can stuff from the part store. Go to an actual shop.

[@damanimcclain2065]

@@HelpingHandAutoRepair should I have them vacuum first then replace or replace and just have them vacuum and fill

[@HelpingHandAutoRepair]

If the air doesn’t work now, chances are the Freon has leaked out. Proper procedure would be to vacuum the system first, replace the compressor then charge the system.

[@robinminter5353]

dude love your video very instructive but can you evac at home with a kit

[@HelpingHandAutoRepair]

Robin Minter There May be a way to do so but there is a specific machine that will suck everything out of the system.

[@tyler646432]

Thanks for the video. Did you reuse the o rings for your high and low pressure lines to the compressor or did it not have any?

[@HelpingHandAutoRepair]

Tyler O I reused the o-rings if I recall. Unless the new compressor came with new ones. You’re good either way.

[@raishun15]

I’m having a hard time what size bolts and how long are the bolts for the mount I lots mine

[@VesselFitterguy]

Can I just fill it back with freon after the install?

[@HelpingHandAutoRepair]

I would strongly advise you to bring it to an AC shop and have them pull a vacuum to check for leaks and to recover whatever might be left in the system and then have them charge it to the appropriate Freon levels if it passes the leak test.

[@jaeramirez6872]

hey bud! thanks for the video. what are the options if i cant remove the stud bolts using a torx e8 socket on an impact driver? my hands are tiredddd

[@HelpingHandAutoRepair]

If you have the correct torx socket, simply get a longer handle to give you leverage to break them free. Alternatively, you may be able to buy these ac port studs at the parts store but I never have (I just transfer them over) so I am not sure if that’s possible.

[@jaeramirez6872]

@@HelpingHandAutoRepair Man they were stripped. Assuming the last person who tried didnt have the righr tool so i gave up. now in search of these studs. Thanks so much lol you saved me a kidney, arm and a leg!

[@jaeramirez6872]

BUT if by any chance you have any more info of finding those studs or rather the specs on the bolts pleaaaaase let me know! been searching for days to no avail

[@HelpingHandAutoRepair]

www.tascaparts.com/oem-parts/mopar-a-c-compressor-stud-6509443aa This is as close as I can find. Might work.

[@jaeramirez6872]

@@HelpingHandAutoRepair i can cry! this heatwave is insane. you my friend. have a well rounded fan 😄

[@amaliocalderon2036]

Hi, Do i have to change the condenser? Many of the AC manufacturers recommend changing it? Also did you flush the system from the oil?

[@HelpingHandAutoRepair]

AMALIO CALDERON It is recommended to do so however auto repair shops won’t do this. They will just replace the compressor. Unless there was some other catastrophic failure.

[@hilarylapke5007]

What are the tools you used throughout the whole video?

[@HelpingHandAutoRepair]

Don’t remember them all. If you follow the video, I try to tell you which size socket or wrench is needed.

[@davebutler95]

15mm socket (or wrench) 13mm wrench 10mm (or 11mm) socket Extension/breaker bar Flat-head screwdriver Torx E8 socket

[@sidneysanders5726]

They made the 4.7 V8 from 1999 to 2011. And the way that belt is routed is messing with me a little bit lol.

[@AirWalker23]

you didn't add rag oil?

[@HelpingHandAutoRepair]

You mean pag oil? The ac shop adds that in when it’s charged.

[@AirWalker23]

@@HelpingHandAutoRepair lol I hit the r instead of the p.... Do you know how many ounces they added by any chance?

[@HelpingHandAutoRepair]

I don’t recall. It was some time ago and this is a customer’s car. I don’t have an ac machine myself. I just handed it off to my buddy who owns a mechanic shop. I let them use their machine to figure out all that information. Most systems don’t require much oil but you would have to find out that information from the manufacturer of the compressor.

[@EHUnlucky7x9]

@@AirWalker23 7 ounce. Pag 100

[@sdedios76]

What about the refrigerant oil?

[@HelpingHandAutoRepair]

You would need to get it charged at an ac shop like I did.

[@sdedios76]

For the compressor?

[@HelpingHandAutoRepair]

Yes. Most are shipped with the correct amount of oil in them already. However if you aren’t sure, take it to an AC shop and have them use their machine to put the correct amount in when they recharge the system.

[@ronaldhernandez7323]

Can you tell me the name of the bracket on minute 8:21 my is missing can you tell me where can I find it

[@HelpingHandAutoRepair]

There doesn’t seem to be a listing on Jeep’s online parts catalog. I am unsure of what to call it.

[@aldumas3517]

​@@HelpingHandAutoRepaires exes t4 rye a2n we t b tz6😮6rr as at

[@carreonnorteno2244]

🙏🏽

[@RamiAq]

I'm about to replace the compressor on my Dakota 2007 on Sunday hopefully. I got a used compressor from LKQ which had only 45k miles on it, so hopefully it will last awhile. The guy at autozone told me they have freon mixed with oil. Do you think it is a good idea to use that or just oil the compressor and then add regular freon? Thank you

[@HelpingHandAutoRepair]

Rami Aqrabawi Is the used compressor completely drained? If so I would use the appropriate oil type then have the system charged

[@RamiAq]

@@HelpingHandAutoRepair it is totally drained out. What type of oil do you suggest? And how do I know how much oil do I need to add? Thank you for your help

[@HelpingHandAutoRepair]

Rami Aqrabawi You will want to use PAG 46 oil. In most cases you will End up using 1.5 to 2 OUNCES of oil. Nothing more. There may be a sticker in the engine bay that will specify how much oil to add but if there isn’t then 2 OUNCES or slightly less will work fine.

[@RamiAq]

@@HelpingHandAutoRepair at the parts shop they told me I need PAG 100. should I use that?

[@HelpingHandAutoRepair]

Rami Aqrabawi You can. They picked that because they really don’t know which one your car takes and PAG 100 is universal.

[@mohammedali-ge2ly]

Old one have namber 20 A new one have namber 17 .what difrent

[@HelpingHandAutoRepair]

Don’t know what stamp you are referring to.