2010 Camaro Turbo Exhaust Cutout

I've made this short video explaining where its located and how a 3" electric cut out sounds on a Turbonetics turbocharged Camaro... feel free to comment and ask for questions.

[@Lio88]

Damn bro that Definetly made a difference in the spooling.

[@rjunior2003]

Lio88 yeah bro, I really Like the sound. But I like more the lack of it! push of a button and I can drive in total peace. I actually only drive the car LOUD for a few mins.. 99.9% is quiet mode hahahaha Cant say the sama about your car now....

[@robertstinman7814]

awesome thank you for all the feedback, . not too far from my cam sounds like ...just pulled the trigger on the turbonetics t76 kit..

[@rjunior2003]

Congratulations! Your going to love the kit... Boost is addictive! Hope you have some suspension work and sticky tires hahahaha if you have questions let me know :) I'll be happy to help if I can :D

[@emeraldblaziken]

I am in love with that camaro bud

[@MrAirgunfan]

Did you install the H.U.D on your vehicle if yes from where did you order it and was it a bitch to install it?

[@rjunior2003]

Hey buddy, yes I installed it my self. It was ordered from Gen5DIY.com I've been meaning to upgrade to the color one, I suggest you get that one. If order from there it comes with the plug and play harness :) Installation is not hard but it does take time. You'll remove all the dash including airbags and steering wheel. Don't take short cuts and make sure you have a power cutting tool and a steady hand. It's worth every minute of your time :) I love that thing :)

[@MrAirgunfan]

+Rodolfo Santiago the color hud? So it all comes in a kit to install it? And on the zl1 bumper do you know if it will fit with the heritage grill?

[@rjunior2003]

+Arturo Vasquez yeah there is a color HUD for the 14 plus I believe. It fits the 2010 too :) the kit has everything you need including the plastic bezel. My buddy has that grill. It fits the zl1 bumper no problem.

[@flyby613]

Is it possible to do the QTP electric cut outs and have a MRT v2 exhaust? On my 2015 v6 camaro

[@rjunior2003]

yup, the best place to install them is right after the header collectors. get a muffler shop to install them in place.

[@DopeAssGamers]

I want cutouts but I'm scared I won't pass smog when I have to take it to get smog checked. Sounds so sexy tho lol

[@rjunior2003]

+DopeAssGamers It will not affect the smog check at all. just dont drive in with the cutouts open lol the guy would never know the difference.I drive the car with the cutouts closed 99% of the time. car is nice and quiet, only when some one pisses me off do I let them have it. the look in their faces? priceless!

[@coreyjackson207]

What suspension upgrades are you running and what would you change if you wanted more grip?

[@rjunior2003]

My car is setup for road racing, but most of these mods can be cross-reference for drag too.1. Solid Sub-frame Bushings (removes rear end "loose whip" feeling under hard acceleration.)2. aFe rear Toe & trailing control arms (keeps car straight and reduces wheel hop.) 3. Polyurethane bushings all around (increases steering response and reduces over-steer)4. BC coilovers adjustable damping and rebound ( Hard rear soft front for drag, road racing is a bit more involved and varies from track to track)5. Sway bars ( no upgrade required for drag, but very important for road racing, reduces body roll.)6. drag alignment, rear - as close to 0 camber .15 toe IN, Front -1 to -1.5 camber, 0 toe6. road alignment, rear -.8 to -1.2 camber .12 toe IN, Front -1.2 to -2.4 camber, 0 to .05 toe out (these settings vary from track to track weight distribution, road condition etc. 7. and most important: good rubber! best street tire in my opinion Michelin Pilot Super Sports $$$ bring your walletcurrently running Continental Extreme Contact WS6 & is a happy compromise between performance and $my size setup 315-35-20 rear, 275-40-20 front. this setup hooks about 600 WHP from a dig with proper alignment.anything more than that and you'll need to start looking a M/T tires drag on a small 16" wheel for serious competitive performance.

[@coreyjackson207]

Extremely helpful. Trans build?

[@rjunior2003]

Manual trans has been pushed over 1000hp without mods - axels, output shaft & differential will pop at around 600rwhp with aggressive launch from weakest link all the way to the tranny. that's assuming your not slipping the clutch. I have a twin clutch Center force on mine capable of +1000 torque.from a roll they seem to do just fine, I've seen people pushing +800 with easy launch. ticking time bomb in my opinion. wheel hop will kill your axels even with less HP.Auto is easier on the axels and output shafts but only by a slight %. you'll need different torque converters as your HP goes up.

[@robertstinman7814]

do you have to run two different tunes open vs closed? you dont lean out with them open? im thinking of picking up a turbonetics kit but i dont want to lose my cam chop and open header sound haha. also are you running catless ? i think i saw another post that said you were tuned by jannetty .. did you find that to be worth it over the kit canned tune? thanks!

[@rjunior2003]

No it's the same tune, I have a mass density tune and it compensates :) spool is increase dramatically with it open do. Traction is a real issue 1st 2nd and sometimes 3rd depending on road and weather conditions. The sound of the car does change a lot. If you look at my videos I had long tubes with flowmasters before the turbo and I loved it. After the turbo I didn't like it until I added the cutout. With the turbo there was rasp that I didn't like. That's why I added the resonated magnaflow X pipe. With the cut out I can hear my cam chop real nice still :) I don't have cats... Over all I love the setup now. Sleeper, and when I need to beast! People don't expect it it's awesome :D

[@robertstinman7814]

Awesome that's exactly what I was hoping. I'm cammed with headers / cut outs now and it's hard to think of having a quite car again which is inevitable with the single turbo set ups I feel like .. untill I saw this haha

[@FerRod2113]

Can you put the link where you bought it?

[@rjunior2003]

Smoky m.summitracing.com/parts/qtp-qtec35cp?seid=srese1&cm_mmc=pla-google-_-shopping-_-srese1-_-quick-time-performance&gclid=CN61m4fL8s8CFU9afgodWzYMnA

[@rjunior2003]

Smoky or google QTP 3" electric cutout

[@robertstinman7814]

what cam are you running . if you dont mind me asking?

[@rjunior2003]

It's a custom ground cam from CompCams 222/236, 114 LSA and a 0.6" lift

[@kinomendoza6797]

How do you like the turbo?

[@rjunior2003]

I love the thing bro! Best Mod I've ever done... $$$ expensive... But puts a smile on my face every time I get on it. Plus there are so few turbo camaros in my town it breaks necks every time that turbo spools lol

[@AbeSpec]

Where did you buy it?

[@rjunior2003]

I got mine on ebay, about $100 and had a muffler shop weld it in place. Only thin I had to do was use red lock tight on every bolt so that it doesn't vibrate loose. Had it for a year now, no issues. You can get higher quality ones on jegs or summit racing.

[@kevinlemus5028]

Would you sell your Camaro ss ?

[@rjunior2003]

that's funny, just told a guy on Instagram I would sell for 35k

[@BlackRecoil]

this gotta be oxnard lmao