2013 - 2017 Honda Accord Strut Mount or Strut Replacement, front end noise

Рет қаралды 30,528

Romy-WhyPay-DIY

Күн бұрын

Пікірлер: 43

@ChukwuOhagu Жыл бұрын

I'm changing my by morning. Thank you so much. This video was enlightening

@whypaydiy Жыл бұрын

Your welcome

@AlexisHernandez-eg1oq Жыл бұрын

Explain everything very well 👍 more vids like this

@whypaydiy Жыл бұрын

Thank you

@Kig211 8 ай бұрын

thank you for this post, my dude. very helpful. 💯

@whypaydiy 7 ай бұрын

Your welcome

@alexalonso2807 Жыл бұрын

Thanks for the 411, brother!

@whypaydiy Жыл бұрын

No problem

@nunezhgo Жыл бұрын

thanks the best video so far even though you didn't change the strut but is exactly the same thing lol 😂

@martinsearchinternational3889 2 ай бұрын

So, did the clanking disappear; would you do a follow up video, car ride to demonstrate a lack of clanking, maybe a before and after. Normally, we as an audience try to diagnose things by hearing, seeing, or touching and that would be a great closure-follow up video to this one. Many thanks for considering it.

@whypaydiy 2 ай бұрын

@martinsearchinternational3889 yes the nose stopped and you are correct about the following up vid. However, it did not make it at the time and I never had that issue again, sorry.

@josecomparan2426 5 ай бұрын

Perfect video,thanks 👌 👍

@gaddygaddy2473 11 ай бұрын

Great tutorial!

@libertyforall5117 Жыл бұрын

Nice vedio but putting a vice grip on the strut pole is a very bad idea, if you as much as scratch the pole it will cause the seal to leak and secondly, if the strut pole is sliding down inside you pushing up you have a damaged strut. Quick tip. A bent strut pole will damage the mount.

@whypaydiy Жыл бұрын

You are right and that's why I did not move it at all or spin it, it was just to hold it.

@treyhatton2195 2 ай бұрын

@@whypaydiyjust clamping vise grips onto the strut like that creates marks that can cause a leak ultimately ruining the strut.

@luispagan6549 9 ай бұрын

How did you get the bolt for the strut mount not to spin?

@whypaydiy 9 ай бұрын

Have to use an impach wrench

@theripper121 Жыл бұрын

You make me a little nervous sliding your feet under the car when you only have it up with a floor jack. Never get any of your body bits under a car if it's only supported by a jack and not jack stands...

@whypaydiy Жыл бұрын

That's true, i have 4 jack stands and I was just lazy and said it would be quick. It is always best to use jack stand with jacks.

@abcdefghij27224 24 күн бұрын

What is the name of the black part that sits below the bearing on the spring called?

@whypaydiy 24 күн бұрын

@@abcdefghij27224 Strut rubber boothe or the bump stop

@caudao7756 7 ай бұрын

What’s the tool used to pop the tie rod end out?

@whypaydiy 7 ай бұрын

Ball joint removal tool, get it on amazon cheap like $20

@drailo1669 11 ай бұрын

How'd you get it back in?

@whypaydiy 11 ай бұрын

Its in the video

@nicolaslopez3301 8 ай бұрын

What model/torque is that Rigid?

@whypaydiy 8 ай бұрын

Model # R86212B-AC87004

@Slowcr.2 Жыл бұрын

is it difficult to pop the cv axle back in?

@whypaydiy Жыл бұрын

No, it is not. It's a tripod bearing that slides in a slot.

@Slowcr.2 Жыл бұрын

I wish you showed that part a little more but ty

@whypaydiy Жыл бұрын

@ackeem Smith it did not come out on the booth. So it is show in the vid. Just don't remove the both and you good

@careful7951 9 ай бұрын

To do this job properly you have to take the lower ball joint out and separate it from the knuckle and take the axle out of the knuckle. Remove the knuckle from the strut and the strut will come right out . This is not a job you should do on the street. You see he doesn’t show how he got the strut and knuckle lined back up. It was probably him and two other people.😂😂😂

@Yoman6767 5 ай бұрын

I tried doing it his way and you are right. I had to ask my friend for help and we STILL struggled with 2 people to get the strut back into the knuckle. I will try your way now for the other side. Thank you 7951!