2013-2018 Ram 2500 Axle U-Joint Replacement Part 1

[@mcronnyvv]

Yea, so I wanted to see how it all came apart and or worked. Seemed like you FF past each of the key moments, IDK I feel like I have the exact amount of knowledge as before I spent this 14 minutes of my life LOL. great camera though. And thanks for putting yourself out there for dumb asses like me to complain about lol. All the best. Thanks for the show and tell.

[@manny9649]

For those wondering, you’ll want to do Spicer joints rather than junk moog. Great video though.

[@toolfan9763]

Greaseless always seemed to do well for me too

[@thordiesel6.7]

How long do the spicer ujoints last?

[@Da9guy1993]

got a part number?

[@brianpool2474]

You should change the wheel bearing at the same time

[@randallscott1915]

Changing my hubs and front axles joints today. Video says 40-50K is normal. I Guess como have been riding on borrowed time for the last 200K. First change out today at 241,000 miles.

[@jamesbloodworth4303]

Is there any kinda axle seal mine is making similar noise but is also leaking fluid behind drivers tire at the end of the axle.

[@richg.2579]

Thanks wasn't sure how to pop the shaft out after I got it all apart

[@mcronnyvv]

I still don’t know, How do you get it out ? It looked as if he just pulled it right out… is that what happened? PLEASE HELP. shite. He seemed to FF past each key point that I wanted to see how it worked. IDK I feel that I have the exact amount of knowledge as before I wasted 14 minutes of my life LOL. great camera though

[@richg.2579]

@@mcronnyvv yes it just pulls right out

[@dougthewelder]

40 to 69k miles? I'm doing my first rear u joints at 260k.

[@Storm.Cloudz]

Mine isn’t as bad as yours but mine clicks every time It rotates. I was able to wiggle it by hand and see it move

[@darienharm3364]

Whats was the part number?

[@jessemartin3996]

Do you have to do anything in the front diff to get the axle out and then back in? I was told you should tear it down. I have a 2014 that has a studder when the steering wheel is going back to center after turn.

[@HoldenPowell_]

I had to because of the passenger side but not because of the driver side, it’s to must to explain it hear but watch my part 2 of it and it will explain it way better and in detail. I think there’s a way to get around it to not have to thatI didn’t know at the time so I shared in that video what I learned to help you!

[@jessemartin3996]

@@HoldenPowell_ I saw what you were talking about but you don't have to tear the diff down to do it right? Just need to put it in 4 wheel drive?

[@HoldenPowell_]

@@jessemartin3996 that’s what I would try and I don’t see why it wouldn’t work because it’s slid onto the inner shaft instead of just the axle which is why mine fell off

[@garygriffiths5384]

Wonder if the #479s will fit the 2019 5th gen..

[@richg.2579]

Audio too low can't hear you

[@alexhazell4272]

Would have been an awesome video if you had done like you said and actually talked through one and not done a Timelapse.

[@HoldenPowell_]

@@alexhazell4272 would of been a 2hr video

[@devincox4889]

What size is the axel nut?

[@HoldenPowell_]

I can’t remember right off the top of my head but I’m pretty sure 1 3/8

[@devincox4889]

@@HoldenPowell_ thanks buddy. Doing mine in the morning

[@HoldenPowell_]

Your welcome and make sure the watch my second video to see the issue I had with the actuator coming about, I believe the way to not have that issue is to put it into 4wd before taking the passenger side out. I would be my solution but definitely watch part to to see what I mean!

[@curtishyde2]

1 5/16 just did mine today on a 2014.

[@HoldenPowell_]

@@curtishyde2 thanks for the info I couldn’t remember from when I did mine

[@stevezakis3274]

Hi speed video. You don’t show what you do!

[@briankohl9951]

You don’t explain anything. Your fast forward through whole video. Why have a how to video if you don’t explain anything