Rob Merry Christmas and a Happy New Year. Thanks for all the time you put into making and sharing your videos. Have an enjoyable holiday 🎄
@RobertDotterer2 жыл бұрын
I appreciate you taking time to watch them. Merry Christmas!
@franciscoxaviergonzalezrom46482 жыл бұрын
What a video Rob! I'm just wondering ... why at the beginning the scanner did not do the full scan? when you put your breakout box everything went back to life...... I wish you the best 2022... nice diag!
@RobertDotterer2 жыл бұрын
I'm not sure why I didn't. I really only needed Engine data at the time.
@jays13593 ай бұрын
Hi. I realize this vid was from quite some time ago, but i've run into the same problem with the roller being reversed. How did u get that out? Thanks in advance.
@RobertDotterer3 ай бұрын
I pulled it out with pliers. It was really stuck.
@jays13593 ай бұрын
@@RobertDotterer What is the part called. I'm fairly certain it will get damaged along the way....
@jays13593 ай бұрын
@@RobertDotterer i've been trying all day to get this out...any other advice or technique you could pass on?
@gcmd58522 жыл бұрын
Never seen one put in backwards, Nice find! That pump lifter usually gets left out during engine swaps and run on low side fuel pressure just not very good.
@RobertDotterer2 жыл бұрын
Thank you for watching. I did not even know it could be put in backwards.
@andrewa.800 Жыл бұрын
Backwards from factory? Or during a repair?
@CarlosRamirez-qw3ne27 күн бұрын
Mine does the same but gave me a code for the fuel rail pressure sensor. Would that be the cause?
@donovanmarable45952 ай бұрын
Hi 2015 ats car first started with stability. Trak and traction control then started to idle rough and gear down rough pulled over turned off on nothing came back hour later came back misfire cylinder four changed sparks coils in all afterwards ran fine idled better then next morning came back Same codes idle rough wanted to dies realized Pcv lines were cracked changed both cleared codes traction back and stability rough idle again misfire four again
@yassmoney56gaming1911 ай бұрын
Hi rob I have been looking for videos that similar issues with the same exact car and your video told me a lot about my car and but still I haven’t been able to find the exact issue with the car would it be possible if I could contact you on email or number so I can send you the codes it’s throwing at me and how the car sounds when it’s running idk if this to much ask please I need help with this car
@RobertDotterer11 ай бұрын
youtube@dotterersautoservice.com
@MrApresmoiledeluge Жыл бұрын
Why isn't it possible to replace the piston directly unless it has scored the crap out of the cylinder, even still could maybe be sleeved right? IDK new motor would fix it but das expensive.
@RobertDotterer Жыл бұрын
Till you get done tearing the motor apart, buying new bolts, gaskets, honing the block, new timing set, checking everything, and buying new pistons and rings for each cylinder, it just isn't worth the money versus buying a new block. I haven't checked in a while but new long blocks used to only be $1600-$1800 from GM
@blakeamerica Жыл бұрын
How did you get the plug out? Got one seems to be seized in there.
@RobertDotterer10 ай бұрын
I pulled it out with pliers.
@blakeamerica10 ай бұрын
@@RobertDotterer i ended up removing the valve cover. Apparently the person before me put it in backwards.....
@oscarcee683111 ай бұрын
You can remove the pump without removing the intake ?
@RobertDotterer11 ай бұрын
I don't remember the video but if I did it in the video then yes.
@dwinters89 Жыл бұрын
So a fuel pump could make it misfire bc mines saying cylinder 4 but I change everything
@RobertDotterer Жыл бұрын
It can, you have to be careful throwing parts at a car without diagnosing it. You can create other problems
@loading...75832 жыл бұрын
So it needs a new engine?
@bartscave2 жыл бұрын
Desired fuel psi 0?
@RobertDotterer2 жыл бұрын
Where in the video did you see that? It may command zero when not cranking.
@bartscave2 жыл бұрын
@@RobertDotterer It was on the scan tool (11:51)but later I noticed a second pid below it with a plausible number
@RobertDotterer2 жыл бұрын
I think the pid just didn't update or something happened.
@dislikebutton4759 Жыл бұрын
My car sounds the same 4th cylinder what do I do ?