2015 - 2019 Mustang GT Borla S-Type Installation EASY - DIY

How to install a Borla S-Type Exhaust Mufflers on a 2016 and newer Mustang GT . 5.0 , Sound clips vs stock This Borla Stinger S-Type Axle-back exhaust system is designed for use on 2015-2016 GT Fastback Mustangs equipped with the Coyote 5.0L V8 engine Stinger muffler MPN# 11887 387464. I also show you exhaust sound clips and drive by's. Included is how a mustang sounds with no mufflers too, you will be surprised!
Come check out my other videos linked below for more auto mechanic how to's.. I am the only klown in the world that can show you how to work on cars! I have something for everybody, from race cars to regular street DIY small projects..
Heat door actuator replacement:
• How to Replace a DRIVE...
Changing a mechanical Fan to an electric Fan:
• Mechanical Fan To Elec...
How to Convert a Stick Shift Car To a Modern Automatic Transmission:
• How To Convert a Stick...

[@willkeen5010]

Jacking up from the control arms, sounds like a better idea than trying to reverse up onto ramps. Thanks for the video!

[@klowny1969]

Thanks for watching

[@randallcunninghamjr.9270]

Awesome video. Ever since I bought my brand new Mustang 2017 GT fall of 2017 I began searching exhausts. When I finally decided on Borla Sport Axle back I then found your video. I’m 48 and for the most part very handy. I sometimes have trouble with my hands / wrists. Something I was born With. In March 2019 I ordered the mufflers from a Borla re-watched your video a few times. It came out PERFECT! looks like a professional install and sounds great! thanks to you! 🏁

[@klowny1969]

Glad i was able to help..don't forget to subscribe

[@Krisp97]

This is a perfect sounding mustang IMO. Not too obnoxious like most lately, but has great sound. Great choice bro

[@klowny1969]

Thanks..dont forget to subscribe and hit that bell

[@private7384]

This is the only clip i've seen of the Borlas that dont sound like crap.

[@klowny1969]

private lol

[@jayb4261]

Thanks for the video. I installed mine today without any problems.

[@klowny1969]

Jerry LaRue awesome!!

[@willkeen5010]

Great video, getting ready to do this on my v6. Quick question for you. I have rhino ramps but was worried about backing up on them till I found your video. When you jacked up from the control arms, did you go full height on the drivers side put the block under the tire and let the pass side just hang there and then jack up the pass side that was in the video or did you use 2 jacks?

[@6spd85notch]

sounds awesome. I have the same car but a 15. now if you buy the ford racing x-pipe you basically have the whole borla catback and you saved a few hundred bucks.

[@klowny1969]

kool thnx for watching and commenting

[@Mave242]

nice sound! nice video! thx! getting my pony in january 2018

[@klowny1969]

Mave242 cool

[@Mave242]

cant wait for it. cant wait to drive it on our german "autobahn" :-P well..how is the sound of Borla-s inside the car? i dislike it loud or to much bass-like. i prefer the sound more dirty.

[@klowny1969]

Mave242 this was a customers caf

[@klowny1969]

Mave242 car

[@nicholaszvalentine9765]

"Lets cut this bitch!" Love it lol😂

[@klowny1969]

Yeah baby..don't forget to subscribe

[@nicholaszvalentine9765]

@@klowny1969 will do!

[@nikolzew]

very informative instruction on how to do it your self ,

[@klowny1969]

thanks for watching

[@Bruce6001]

Sounds great 👍🏻

[@klowny1969]

Thank you

[@dennisasheim8328]

Very nice. Sounds great!

[@klowny1969]

Thanks for watching

[@ahmedsabah787]

sounds better without a muffler !

[@klowny1969]

+The chosen one i agree lol thnx for watching

[@Network-Mike]

Wow, that sounds pretty awesome without any mufflers!

[@klowny1969]

+Mike Adkins Yes it did lol

[@mervynguintu8064]

fast work bro 👍

[@klowny1969]

thanks for watching

[@goomaan]

Great Logo!! As always clean work!!!

[@klowny1969]

+Glen Ohringer thanks for the logo gleany

[@125sm3]

Loud is best !!!

[@klowny1969]

125 SM yes

[@ortiz630]

Great DYI, going to work on mine

[@klowny1969]

Eddie Ortiz thanks for watching and commenting

[@MustngRydr]

Thanks for this video! Helps me know that I can do it without a Lift! Im getting the Roush Axle-Back exhaust though!

[@klowny1969]

+Justin Diaz (MustngRydr) great.thanks for watching

[@AntLive29]

love those jack stands!

[@klowny1969]

thanks

[@Fireship1]

They sound great Manny. Best time to chop off stock exhaust is when it's brand new! No rust to deal with. Going to do the same on my new f150 5.0 with borla or flowmaster. Thanks for the vid.

[@klowny1969]

+Fireship1 thanks sir! That f150 will sound awesome! Good luck!

[@thegreatest8112]

It sound better before, still cool tho

[@klowny1969]

Thank you

[@jonathanrowe7587]

Can't believe you have to cut on the newer body styles! I have a '14 and put a corsa xtreme axle back on and it just bolted up!!

[@hatterz9548]

Great video. You should should put an x-pipe on it.

[@ams914]

Sounds nice. Not too loud either right? Not over the top.

[@klowny1969]

ams914 i dont think it was too loud..dont really remember

[@SteveRobReviews]

Terrific vid Fred, could the owner feel any performance benefit ?

[@klowny1969]

+Steve Rob My name is Gerardo..no performance benefit ..just louder lol thanks for watching

[@SteveRobReviews]

+klowny1969 Ha ok I'm writing it down , you have a good night .

[@klowny1969]

+Steve Rob its Manny lol thanks u 2

[@SteveRobReviews]

+klowny1969 man your as twisted as I am, ha I know you name , your awesome buddy LMAO

[@klowny1969]

+Steve Rob :D

[@fpelinity]

I also have the 2016 GT but in yellow with the black accent. Will changing the exhaust void the warranty?

[@klowny1969]

+Pikachu GT probably not..but i would still inquire with ur dealer

[@ps31871]

sounds better with no mufflers haha! but roush exhaust sounds better!

[@dustinmartin8038]

ps31871 no it doesn’t. Roush is raspy and sounds like garbage. Moron.

[@GhettoWagon]

It sounds good with no mufflers! alot of cars sound bad w/o them! Exhaust on your back in the driveway, never fun! Where did you get the band clamp? I need one like that.

[@klowny1969]

yes it did lol..the band clamps came with the mufflers..ur local auto parts store should have similar ones though..thanks for watching

[@GhettoWagon]

Naww those band clamps are hard to find. Auto parts stores sell nada like that. I have stepped lap joint clamps now, they are not too hot, I like that style better. Alot of OE's are using them now on new cars, Stainless too. Finding them on the aftermarket is tricky. klowny1969

[@klowny1969]

+Ghetto Wagon These are pretty much them..believe it or not..there are auto parts stores by me that have these lol www.jegs.com/i/PYPES/958/HVC24/10002/-1?CAWELAID=230006180000134041&CAGPSPN=pla&gclid=Cj0KEQiAvuWyBRDO_Yzhpv_4nvEBEiQANBdXMmkSrS4V6bvLI4-mrr5Ahv2FSGh_23hQ_XE-PUSsykYaArzQ8P8HAQ

[@GhettoWagon]

Oriely's seems to stock alot of clamps but the closest sore is 80 miles away. I found some walker stainless ones on amazon, they look like that. Thanks klowny1969

[@willkeen5010]

Finally getting ready to do this on my v6. I have a set of rhino ramps but was worried about trying to back up onto them. I see that you jacked up on the control arms and put blocks under the tires. Quick question for you. Did you use 2 jacks or just jack the drivers side to full height and just let the passenger side hang there or did you support the passenger side with another jack or stand?

[@klowny1969]

Post a comment Below..lemme know what you think of the video...Thanks

[@enrique19az]

para que suene vonito hayque cambiar toda la tuberia no nomas el cilenciador jajajaja

[@klowny1969]

no habla Español

[@enrique19az]

+klowny1969 frame change all piping

[@everardocamacho5063]

great lightting on the old mustang, do you a set for 89 toyota truck?

[@klowny1969]

sorry im not sure i understand

[@lebronblew5finalsnottop5ne22]

I have a question I'm restore my 1970 Cutlass supreme And I wanted to know how I can take off the fender emblem. I hope you can do a video to help me out. I can't find any info anywhere on how to. thanks !

[@1239-k8p]

The full name and description of the jack?

[@ccbusa05]

Nice video. I just would like to double check; is it OK to use that jacking point as shown at 0:50 into the video?

[@deedee6950]

Did you get a h / x pipe with the exhaust pipe or did you stick with stock pipe

[@klowny1969]

not my car..it was a customers car

[@deedee6950]

+klowny1969 ookk....

[@LynxStarAuto]

Ahh see now you are working on the man stuff... Fords! None of those chebby boy toys

[@klowny1969]

lol

[@realmuzafarumarov]

nice install. car is from Sterling Koon's. where in VA are you?

[@klowny1969]

+Muzafar Umarov Thanks..im in New york

[@theoneandonlyslickrick4132]

I have a 17 GT and I love my stang!! You keeping yours for a while or what?

[@theoneandonlyslickrick4132]

Bro where do you live? I am coming over so you can help install mine.

[@klowny1969]

Slick Rick sorry im backed up for couple months..thanks for watching and commenting

[@xevious2501]

no exhuast sounds best, and a heck of a lot like the GT350R with exhuast full open. hmmmm

[@gorillazgarage7482]

When did you start a blogging channel Stallone??

[@klowny1969]

Joseph Ojea about 4 years ago

[@gorillazgarage7482]

klowny1969 haha classic bro 😄✊️

[@klowny1969]

Joseph Ojea 😆

[@gorillazgarage7482]

klowny1969 real talk.. I'm getting ready to order up a s type cat back.. what do you have to say about it after having it for a while? I'm trying to pick between that and corsa or roush.. but I can't make up my mind.. so think I'm just gona pull the trigger on the borla and try it out..

[@klowny1969]

Joseph Ojea this was a customers car..as far as i know he was happy with it

[@jcbeatz5596]

Better to weld instead of clamps. I got roushe

[@romeohi7940]

mustang 2015 sucks