How remove and replace a front bearing on a ford escape without losing alignment in the same vehicle. Como se remplaza un balero delantero y una maza en el mismo carro sin perder la alineacion en una camioneta Ford 2015
Пікірлер: 39
@johnm1901 Жыл бұрын
That poor brake caliper hose is the first thing I noticed when the video started.
@johnm1901 Жыл бұрын
It’s an excellent step by step video. Absolutely saved and liked. 👍🏽
@lewisellis760810 ай бұрын
Well done very helpful
@olveragarage10 ай бұрын
Thanks
@nexxusty2 жыл бұрын
Thank you. I am going to attempt this repair ASAP myself. Saved me from replacing the whole part.
@olveragarage2 жыл бұрын
Any time good look
@hairlesschimp479 Жыл бұрын
The caliper!…
@johnsanchez13482 жыл бұрын
Appreciate your video, had useful information I couldn't find in any other videos. Now if I can only get the hub off using my slide hammer lol. Been sliding that thing for an hour and it's not budging. Might have to use heat and some wedges with it. Thanks again.
@olveragarage2 жыл бұрын
Thanks
@jesusxocua1787 Жыл бұрын
Muchas gracias por su ayuda mi amigo, DIOS lo bendiga siempre 🙏🏽.
@olveragarage Жыл бұрын
Gracias igualmente
@crobinsfly99793 жыл бұрын
Appreciate the video, I did both sides of an Escape at 130kmi. The only improvement I suggest is to use a dremel to cut a small notch in the old bearing race on the hub(it doesn't even have to be completely through), then, using a chisel and hammer, smack the race a few times until it breaks free. That task shouldn't take more than about 5 minutes and it will save you >70 dollars because you can reuse the hubs. Hardest part for me was using the slide hammer, >45 minutes messing with that and I had to use some wedges hammered in between the hub and knuckle to finally break it free.
@olveragarage3 жыл бұрын
I will take your information into thank you
@icandoit203 жыл бұрын
I was wondering if the hubs could be reused. Good tip. Thanks!
@nexxusty2 жыл бұрын
This is huge. Thank you for typing this out brother. Respect.
@e.tylerwright34833 жыл бұрын
I'm going to have to do this soon and I thank you VERY much!!
@olveragarage3 жыл бұрын
Any time
@taylormorris7364 Жыл бұрын
Thank you very helpful
@olveragarage Жыл бұрын
Thanks for watching this video. Any time you have any questions please let me know.
@thestig1899 Жыл бұрын
Which Milwaukee impact you use ?
@olveragarage Жыл бұрын
Wrenches Milwaukee M18 FUEL ONE-KEY 18V Lithium-Ion Brushless Cordless 1/2 in. Impact Wrench with Friction Ring
@JoseFlores-kc9pu2 жыл бұрын
Que tal Olvera G. Exelente contenido 👍🏻, que sucede si solo se cambia el balero y la segunda pieza se coloca la misma que tenía el carro.. presenta algún ruido ?.. O es necesario cambiar ambas piezas .? Gracias .. saludos
@olveragarage2 жыл бұрын
Jose flores si la masa tiene desgaste es mejor cambiarla ya que tendrá juego y u balero no durara mucho tiempo por eso yo siempre cambio ambas saludos y gracias por tu comentario.
@jimroe54242 жыл бұрын
Another method to remove the inner race from the hub is to heat the ring with a torch, it will expand and slide off easily
@jesusxocua1787 Жыл бұрын
Excelente video. Donde puedo comprar la herramienta para sacar el bearing. Gracias amigo 🙏🏽
@olveragarage Жыл бұрын
Saludos Jesus en usa algunos o railes los tienen en renta pero si no en amazon otc 6575. Oem tools27213 o en harbor freight MADDOX Front Wheel Drive Bearing Remover and Installer Kit, 21 Piece.
@Doctor-lx9ed2 жыл бұрын
where did you get that tool i need one so bad such a life saver lol
@olveragarage2 жыл бұрын
Front otc 6575 hub grappler puller
@Doctor-lx9ed2 жыл бұрын
@@olveragarage thank you life saver
@rogeliovazquez912 Жыл бұрын
Esa herramienta para sacar el balero la rentan ? En auto zone ? Buen vídeo
@olveragarage Жыл бұрын
Saludos me parece q en solo algunos o raiies, la que yo tengo es otc 6575. Pero si esta puedes comprarla en harbor freight MADDOX Front Wheel Drive Bearing Remover and Installer Kit, 21 Piece.
@marianarodriguez2841Ай бұрын
Como hizo para meter el ring de metal que asegura después de haber metido el bearing ? El que va alreded del speed sensor. No logro meterlo 😢
@olveragarageАй бұрын
Lo puede acer con unas pinzas de punta o con unos desarmadores planos solo tengas mucho cuidado ya que se puede chispar y podria pagarle en un ojos asi que use lentes de protecion. Intense meter un lado donde empieza el seguro y con desarmador plano aga precion para empugarlo a la pocion. Si eso no funciona recomiendo consign una pinzas de seguros
@marianarodriguez2841Ай бұрын
@@olveragaragegracias
@CatRacer1A2A2 жыл бұрын
Just letting the brake caliper hang on the brake line huh? Mechanical 101.... don't EVER do that
@toddbob552 жыл бұрын
been doing it for 40+ years it wont hurt a thing.
@nexxusty2 жыл бұрын
It doesn't hurt anything if the caliper line isn't visibly messed up.
@nexxusty2 жыл бұрын
@@toddbob55 EXACTLY. Tell em'.
@CatRacer1A2A2 жыл бұрын
That's ok. If good enough is good enough for you guys, that's fine. There is a reason I get to work at the level I do... subtle details such as this. Always strive for better and never "good enough."